Another grip tip: try using hairspray... spray down the bar and the inside of the grip... it slips on easy and after the alcohol evaporates the remaining adhesives provide a great lock onto the bar.
Tip 4 - to speed this up further, put your air gun in the hole you made at the end. It also saves you from twisting grips with patterns or designs on. Also with regards to tip 4, the vast majority of the panels and even some components on my AJP rat bike are held on or in place with lock wire :P Tip 2 - they're cable ties...mine are, wait for it, cable tied to the frame! Using 2 of the cable ties mean you can put the whole pack on the frame, or anywhere else, if you want, and as you use more, you just tighten the one holding them in place.
I filled my handlebars with silicon to compensate for the loss of bar-end weights, and it melts in the summer and gets under the left grip making it very difficult to stabilize. Regret putting it in there. Not sure if the vibration is less or if I just got used to it, either.
Saw this video and 2 weeks later my engine started knocking on a trail ride. I got off the bike, started spitting on it furiously, and it worked! Sold the bike a few days later as “almost new” thanks man!!
What brand seat cover is that? Black bird? I recently put a Chinese cover on and it was a bit short,and I screwed it up,no more Chinese parts for my Japanese bike
Brad, what abut redirecting vent tubes from carb to air box??, I´m surprise works bikes don´t do that to prevent water into the carb....it´d be a great problem during a race, for ex Spanish round 2019 I always do that to every bike I own, surprise factory bikes without that trick
@@bradfreeman7916 is your clutch master cylinder stock? I have the 300rr racing 2020 and the nut and washer that connect the clutch hose are visible. In your bike everything is under that rubber thingy.
Not to be pretentious but you inspired me to get my 2020 Beta 300RR RE. Do you normally run your throttle so far up (rotated back) like that? I struggle with a little bit of arm pump because of wrist mobility issues and I'm always trying to figure something out with the throttle. Any tips? Thank you!
Thanks dude! Yeah you can do a few things...rotate the throttle back a little like mine...try thinner/softer grips...loose fiting gloves...try also having the front brake a little more sharp (less travel on the lever) hope this helps!
Hoe have special fibre for around you exhaust that keeps the heat inside the exhaust and away from your tubes and also doesnt warm the kooling water inside the tubes
If you put glue on your head then put your helmet on you put a little spit on it to make it look nice that's a really great hack for your helmet and also if you spray paint your goggles black it helps with the Sun make sure you put a thick layer then put some saliva to make it look nice
There was a big hole in the back of my bike that was puffing air so I siliconed it up
Ha that’s funny
I really hope your joking
Did u put a bit of spit if not it wasn’t done correctly...
Master Jcp only joking 😂
"A bit of spit" ?? Holy hell! I've seen Wet Willie's given with less spit than that! 🤔🤢
😂😂😂
You are a spitting cobra!ahahah😂🤣
Need a top end rebuild? Silicon and some spit should do the trick 😂😂😂
These videos are honestly some of the best, please don't stop.
Not many factory riders share these little tricks, thanks Brad.
Glad you liked it! Thanks man 🤟🏼🔥
For the grips, you can also use spray paint and they slide right in and are pretty solid after they dry
Nice try 😂😂
Playground Beefs I am being for real. Lmao. It works.
Hairspray 👌🏼
No it really works. Just use clear spray paint so u never know its there. Spray it insinde the grip and slide it on. Once it dries its solid.
cTatham 36 it works tho he wasn’t joking just has the clear one
Another grip tip: try using hairspray... spray down the bar and the inside of the grip... it slips on easy and after the alcohol evaporates the remaining adhesives provide a great lock onto the bar.
Brad, where can one get the 8 mm brake pad pin? And I see you use a bolt and nut configuration for the rear brake lever clevis as well.
You can find them easily on the internet 👍🏻
Love the videos, keep it up!
Thanks!!
Very nice! never stop learning tips!
thank you
Tip 4 - to speed this up further, put your air gun in the hole you made at the end. It also saves you from twisting grips with patterns or designs on.
Also with regards to tip 4, the vast majority of the panels and even some components on my AJP rat bike are held on or in place with lock wire :P
Tip 2 - they're cable ties...mine are, wait for it, cable tied to the frame! Using 2 of the cable ties mean you can put the whole pack on the frame, or anywhere else, if you want, and as you use more, you just tighten the one holding them in place.
Brad’s first aid tips...
Bit of a scuff, just use some spit. Nasty gash, silicon first then smooth over with some spit
Thank you very much for te foam tip bc my seat does not fit perfecly at the back and watet keps geting in my air box
I filled my handlebars with silicon to compensate for the loss of bar-end weights, and it melts in the summer and gets under the left grip making it very difficult to stabilize. Regret putting it in there. Not sure if the vibration is less or if I just got used to it, either.
Great vídeo bro!! Awesome bike 😍🔥
Saw this video and 2 weeks later my engine started knocking on a trail ride. I got off the bike, started spitting on it furiously, and it worked! Sold the bike a few days later as “almost new” thanks man!!
For grips I use regular gas no pre mix and You put it in the grip dump it out and then put the grip on the bike
He likes a cable tie or two 🤣🤣 nice
Why did you remove the clock that came stock to strap a watch on the clutch?
What brand seat cover is that? Black bird? I recently put a Chinese cover on and it was a bit short,and I screwed it up,no more Chinese parts for my Japanese bike
Brad, what abut redirecting vent tubes from carb to air box??, I´m surprise works bikes don´t do that to prevent water into the carb....it´d be a great problem during a race, for ex Spanish round 2019
I always do that to every bike I own, surprise factory bikes without that trick
I have done that trick in the past! But haven't had a problem recently with the 2020 Beta...maybe for the future though 👍🏻
Great videos bud, keep them coming 👍😎
Thanks man!!
This is probably the best "bike hacks" type video I've seen so far 👌 I'm all about stashing tools and zipties in weird places on the bike.
Hi Brad! I just wanted to ask, how do you fix that foam under the seat and under the battery? Is it sticked with some glue?
2:30 damm my left fork leg cover always rubbing on the fork cause the brake line is attached to the cover and it pulls it in
Hey man great tips cheers from California
Also what is your bike? I’m looking forward to getting a ktm 450 or 500 what do you recommend
Great tips, much appreciated!
Thanks!
@@bradfreeman7916 is your clutch master cylinder stock? I have the 300rr racing 2020 and the nut and washer that connect the clutch hose are visible. In your bike everything is under that rubber thingy.
Yes the clutch is completely standard...we just use the rubber to stop mud and water getting on to the hose connection 👍🏻
@@bradfreeman7916 Thank you for taking the time answering my silly questions!
Awesome tips man 🔥 Appreciate it.
Not to be pretentious but you inspired me to get my 2020 Beta 300RR RE. Do you normally run your throttle so far up (rotated back) like that? I struggle with a little bit of arm pump because of wrist mobility issues and I'm always trying to figure something out with the throttle. Any tips? Thank you!
Thanks dude! Yeah you can do a few things...rotate the throttle back a little like mine...try thinner/softer grips...loose fiting gloves...try also having the front brake a little more sharp (less travel on the lever) hope this helps!
Thanks for these tips!
Muy buenas sugerencia Brad
Gracias por el video.
Saludos desde Argentina 🇦🇷
just one question , who made you characther in the begining of the video?
Good tips 👍
Great tips!
Ciao campione perché metti il silicone nella leva del cambio? E perché metti le fascette nei raggi?? 💪🔝
Der Schokoriegel Tipp! Beste.
Thanks! 🤟🏼
Goods tips thx Brad !
Glad you liked it!
Nice video!!
Thanks! 💪🏻
Spot on cheers mate 👍
Glad you liked it 🤟🏼
these ate great
Very informative
Great vid!
Thanks!
Great tips ! Cheers From France ✊🏻🔥
Thanks mate!
I'm from France too mate !
If your engine blows up silicone and a bit of spit if you bend your bars silicone and a bit of spit
Original dude
@@bradfreeman7916 just a joke mate sorry if your offended keep up the good vids mate
Wouah it’s very cool. You are the best. Cheers from France 🇫🇷 👌👌
Thanks man!!
Hoe have special fibre for around you exhaust that keeps the heat inside the exhaust and away from your tubes and also doesnt warm the kooling water inside the tubes
nice video bro
need amazon link for spit can’t find it
Keep looking bro
Whats the wire for
That mustache is mean bro! 👨🏻🦰
Thanks mate 😂
Looks like something the missus left behind...
If you put glue on your head then put your helmet on you put a little spit on it to make it look nice that's a really great hack for your helmet and also if you spray paint your goggles black it helps with the Sun make sure you put a thick layer then put some saliva to make it look nice
Hilarious
@@bradfreeman7916 thank u bro
Was expecting another banger reply from you
@@bradfreeman7916 sorry bro it's 2:00 a.m. in the morning I'm playing some call of duty in the garage taking a break with the bubbler lol
If you know what I mean😳
I’m currently 20% bike, 30% silicone and 50% cable ties. Works well
Sure does
Thanksss
No problem 🤙🏼
Hola Brad,saludos desde Argentina... eres mi ídolo☝🏻✊🏻✊🏻.
Puedes poner subtítulos en español??
¡Intentaré!
just saying hi in Australia
Please stop spitting on your bike 💔
why not wear the watch instead of on the bars
Excelente 🇵🇦
Buy a bike made in Italy and all it needs added is some silicone and wire-ties
Up next! How to fix a broken leg wit zip ties, silicone and a bit of spit
Great idea
Thanks man. From Canada.
You forgot to add spit to the cable ties for good measure.
wtf is energy gel???
👌👌👌
Bro used 4cents of silicone on 1cent shifter
BETA POWER !!!
💪🏻💪🏻💪🏻
“Noice” after every hack 😂😂
Bro! Give him a break! LMMFAO!!! 😂😂😂🤣🤣🤣
noice ;)
Best part of that video was the gold bar strapped to the bars.. genius, bad boy biscuits them.
💪🏻😂
Did he really just spit on his finger
Sure did
@@bradfreeman7916 woah
@@bradfreeman7916 you replied
Dafaq is that intro so loud for?
Turn it down then
@@bradfreeman7916 turd
@@V2_Dre you’re a turd
80s footballer look
That's the look I was going for 🤙🏼
Should have left the spit part out 🤮🤮
noice
Bruh the spit like wtf
That was the most disturbing spit I ever saw !!!
I got 28 seconds in and had to turn it off .
Sorry it wasn’t up to your standard
just get a KTM. Solves all your issues 😉
chegey
"I want the spit!" - Charlie Harper
😂😂
MAKE YOUR BIKE LOOK LIKE SHIT *TUTORIAL* NOT CLICKBAIT!!!
Bruh.. the whole spit thing is super cringey
Can barely understand you through all of that mumbling.
5:10 wtf man
Banter
Just spit it for good meusure
You got it
What is it with you and spit it was unnecessary
Sorry if I offended you
I appreciate the Beta/Hitler youth look.
Ffs