This is the only tutorial I’ve found that doesn’t involve destroying the inside of the mold. Plus, using a jigsaw as the vibrator is brilliant! Thanks for taking the time to make this video!
You just need to oil your containers before pouring concrete. It prevents the concrete from sticking to the container and makes it easier to detach later. It’s just a construction technique. As an architect we actually do this to all shuttering for concrete before pouring in the mix. You could use any oil for the matter. Would have saved you a lot of time, buckets and a video 🤗
Oiling doesn't work all the time and demolding the mold from a comparatively thin concrete wall is bit risky. Oiling the mold for thicker concrete elements in the construction field is a different thing.
Get a tub of paste wax and rub a light coat of it on your buckets before pouring the concrete, makes them separate much easier. Also, to go to the next level, you can mix your own concrete blends, just buy Portland cement and sand, mix 1:3, add water that’s 1:5 latex primer paint and water. Will cast much better - less air holes and smoother finish without any aggregate.
Thank you so much for creating such a detailed tutorial! These planters look super sleek. I think I'll definitely be making these for my plants. I also really appreciate the eco friendly and reusable sentiment behind the entire project. Your enthusiasm is infectious!
Seeing how much detail you put into this is inspiring! You clearly make these videos so detailed because you’re very passionate about what you do. And that’s awesome. Keep up the good work!
DRAINAGE hole---yes! Today, I've been looking at many DIY for concrete planters --and you're the 1st to address (& allow) for drainage hole(s). Thanks!
Thanks for the video. This inspired my new method, which is working well for me: -slit the outer bucket down to 1" above the bottom, and drill a small (1/8") hole at the bottom of the slit to help prevent it spreading further. No slit needed in the inner bucket. -install schrader air valve nipples in the bottoms of both buckets. Place a small piece of tape over the concrete-facing side of both air nipples to prevent the concrete from fouling the valve. -After the concrete is cured, hook a bike pump up to the inner bucket's air nipple and pump. The inner bucket immediately separates from the concrete and can be lifted clear. - urn the outer bucket on its side, remove the tape from the side slit, and attach the bike pump. The combination of pumping air in the bottom and flexing the bucket sides quickly separates the outer bucket
your method is excellent. Thanks. I used a different method to easily take out the molds. Be it cut like yours or using original pails, I wrap the inner mold or smaller pail with newspaper, and on top of it, a layer of shrink-wrap to keep the newspaper dry. With that, the pail can be easily removed as it doesn't in direct contact with the cement.
You are definitely a genius! I have been wanting to make big cement planters but didn't know how. Now you know what will keep me busy come Spring. Thanks a bucketful!!!
Great video! The alignment blocks are great for the top. Perhaps you could use a 1/4" pipe nipple/tubing piece through the bottoms of the buckets to align the bottoms and build in your drainage? Also a larger bottom could be made to sit the planter on with 3-4" all the way around for polished rocks, marbles or rock chips. That way you can bottom water your plants. Thanks again!
You are making far too much work for yourself! Here's a tip: First coat the inside of the bucket with silicone or WD40 or plain old cooking oil, before you fill it with cement. Then when the cement has hardened, spin the bucket over and pour boiling water over it, the cement pot will slide out nice and easy! :)
You have some great BRILLIANT tips and tricks! THANK YOU! I need to find something to help supplement my income. I thought about concrete pots. But wasn’t sure. But you have worked out all the issues! I am so grateful. And you give such great instruction, without being too long winded!
Often times when building forms for concrete you can add oil and that will make it easier to remove the forms and finish the concrete surface before it’s completely cured. If you change the oil on your car you can save it and use it for forms.
Your planters turned out great! They look awesome!😎 👏🏼 👏🏼 👏🏼 I’ve made about a dozen and I use inexpensive dollar store coconut oil or vegetable oil as a mode release. It makes life so much easier!!🙂👍🏼
I used a marking gauge (like this: amzn.to/3sMM0kJ), but honestly just using a combination square and marker would work just as great (and a combination square is a more versatile tool to have on hand).
Awesome man thanks I've been looking for something to make planets with great work And poring hot water can help loosen up the plastic and make it easier to remove 👍
You don't need special things to hold the inner bucket.. Fill it with water, problem solved! also, I make these too and I don't cut my bucks at all because I oil the outside of the inner bucket as well as the inside of the outer bucket. The final thing I do is make a handle I can grab and use to release the inner container. I also drill a drain hole and hod it open with a piece of pipe. It's flush and it's oiled so it will come out when I pull it out from the bottom. It all works and I didn't cut anything.
Great Video! Everything was so well explained and easy to follow. Gotta check out some of your other videos, my friend! This was so well done! Thanks for your time and effort!
Thanks for the video, very informative - I’ll definitely give this a try! Also, just wanna say that you’re a natural educator. You look pretty young, so I’m assuming it’s not years of practice - but seriously, you’re really good at getting your point across without me ever losing interest - and even more impressive is that when I thought myself a question about something, you were answering the question I had in the next segue Really impressive my man. Just sub’d, look forward to checking out your other videos, and I definitely wish you and your career choices all the best. Xiao
Great looking planters. The base looks real high end. Definitely can use cheap cooking oil to alleviate sticking but fabulous problem solving, entire video and end product. ✨🫶👏🏼👏🏼👏🏼🪴
nice job!! question: have you ever tried making the concrete just a bit less thick and then pouring? You could probably drill the holes 20 minutes later, yes this would make another place to tape, but as thick as you have it, I wouldn’t think any water or concrete would come through. Thanks for sharing. 🌿
Great video! I have an idea for part two! Do a search for dry pour concrete on youtube. All the trouble you are having with this project all involve wet concrete. If you dry pour, you won’t have any trouble at all. Ha! Then you can do a comparison of wet pour vs dry pour planters to deal with all the haters.
Bro you don't need to cut the bucket. Just apply old engine oil on the inner surface of the bucket before pouring concrete mix. And after the concrete is set just invert the bucket and add boiling water on it. The heat will expand the bucket and the pot will fall off. But your method looks really cool 🔥
Hi! Thanks for this tip, I’ve for sure seen quite a few people do this rather than cutting and taping the buckets. Just wondering what you mean when you say to “invert” the bucket? Do you mean that after you get the inner bucket out you flip the “outer” bucket upside down and pour hot water over the outside/bottom of the bucket and it will release? Hopefully you see my comment as yours was posted 6 months ago l😬 Thanks so much!!!!🤗
@@charliblake8551 Hi, yes you are right. Just turning it upside down and pouring hot boiling water on outer surface of bucket. Also few gentle strikes with a rubber mallet will help. But removing the inside bucket could be troublesome sometimes. Thats why I follow dry concrete mixture method to make pots. You can refer "how to make cement pots" from "urban gardening" yt channel. Hope it helps 👍
Good idea with the precuts in the buckets! Remember to wear gloves when working with any cementious material such a concrete because it is acidic and can cause skin problems. Also, pre-made concrete mix is great but you can also make your own with a cement bag and aggregates of your choosing for more customisations and strenght! Cheers!
If you're worried about cutting yourself, there are gloves available that fit closely but have some steel filament woven through it. They help to prevent cuts. I use them when cutting up glass. I don't know how well they work as I've never cut myself but they're worth a try.
👍🎖🏆🏅Excellent Presentation, Thank you for your detailed explanation for completing the DIY project, please do make more detailed videos to help people like me who are not good handymen.
hi! would you happen to know where I could purchase the alignment blocks online? I don't have a machine to be able to cut out the shape accurately. Any help would be super appreciated :) Thanks so much for the video btw! so helpful!!!
thank you ...excellent video...I would make a rope pull for bottom of inner bucket.. dirll holes and loop twine or chord through two or for holes, making a handle to pull the bottom up also filling that lower cap with stones makes it easier to keep from floating up ... get a "FUNNEL to pour in the remainder of the cement... I will be using this. except I will put my weep holes 2 inches from the bottom around the outside... long story.
🌎❤️🕊😊 😊 Hello! Thank You So Much For Sharing Your Skills! This is my first time Watching You On UA-cam! I Love Your Ideas & Video. I hope you will make more different sizes of Planters . God Bless. Stay Safe!
1.Drill a hole in the large bucket 2.seal it with clay 3. place pvc piece in middle where small bucket will sit on. Pour concrete , weigh down small bucket let sit for 3 days. When ready remove clay from bottom of large pot and BOOM NO SUCTION !!!
This is the only tutorial I’ve found that doesn’t involve destroying the inside of the mold. Plus, using a jigsaw as the vibrator is brilliant! Thanks for taking the time to make this video!
Not using it to cut the buckets tho lol 😅
Sir you are heaven sent this is the best video on concrete planters on youtube
You just need to oil your containers before pouring concrete. It prevents the concrete from sticking to the container and makes it easier to detach later. It’s just a construction technique. As an architect we actually do this to all shuttering for concrete before pouring in the mix. You could use any oil for the matter. Would have saved you a lot of time, buckets and a video 🤗
Use wd40 in the containers before applying the concrete
spent cooking oil will work great, and is technically recycling
@@spod32827 I used cooking oil and I still cant get the container out of the middle.its stucked. What do o do please
I used cooking oil on the container to be placed in the middle and Istill cant remove it .please help
Oiling doesn't work all the time and demolding the mold from a comparatively thin concrete wall is bit risky.
Oiling the mold for thicker concrete elements in the construction field is a different thing.
Get a tub of paste wax and rub a light coat of it on your buckets before pouring the concrete, makes them separate much easier. Also, to go to the next level, you can mix your own concrete blends, just buy Portland cement and sand, mix 1:3, add water that’s 1:5 latex primer paint and water. Will cast much better - less air holes and smoother finish without any aggregate.
After looking at dozens of videos like this I can say that the process is the best.
I love this video. Details without it being overbearing or under informed. Thanks dude.
10 minutes in and I'm convinced you're a genius!! Those spacing blocks!! OMG!!
1 minute in and I had the same feeling
I gotta say, this video surpassed my expectations. Interesting process on making the molds reusable!
Thank you so much for creating such a detailed tutorial! These planters look super sleek. I think I'll definitely be making these for my plants. I also really appreciate the eco friendly and reusable sentiment behind the entire project. Your enthusiasm is infectious!
Seeing how much detail you put into this is inspiring! You clearly make these videos so detailed because you’re very passionate about what you do. And that’s awesome. Keep up the good work!
Dude. You killed it. This is the best concrete demonstration.
You've added alot of value here. Thank you😇😊
DRAINAGE hole---yes! Today, I've been looking at many DIY for concrete planters --and you're the 1st to address (& allow) for drainage hole(s). Thanks!
Looks awesome!
A cork, piece of round wood/Bamboo or drain pipe in the bottom will make your drain hole. That way you don’t have to drill it after.
Thanks for the video. This inspired my new method, which is working well for me:
-slit the outer bucket down to 1" above the bottom, and drill a small (1/8") hole at the bottom of the slit to help prevent it spreading further. No slit needed in the inner bucket.
-install schrader air valve nipples in the bottoms of both buckets. Place a small piece of tape over the concrete-facing side of both air nipples to prevent the concrete from fouling the valve.
-After the concrete is cured, hook a bike pump up to the inner bucket's air nipple and pump. The inner bucket immediately separates from the concrete and can be lifted clear.
- urn the outer bucket on its side, remove the tape from the side slit, and attach the bike pump. The combination of pumping air in the bottom and flexing the bucket sides quickly separates the outer bucket
How does this only have 1k views?! This is so awesome!!
Very detailed explanation 👍
your method is excellent. Thanks. I used a different method to easily take out the molds. Be it cut like yours or using original pails, I wrap the inner mold or smaller pail with newspaper, and on top of it, a layer of shrink-wrap to keep the newspaper dry. With that, the pail can be easily removed as it doesn't in direct contact with the cement.
You are definitely a genius! I have been wanting to make big cement planters but didn't know how. Now you know what will keep me busy come Spring. Thanks a bucketful!!!
I appreciate your attention to detail and explanation. That can be rare
Great video!
The alignment blocks are great for the top.
Perhaps you could use a 1/4" pipe nipple/tubing piece through the bottoms of the buckets to align the bottoms and build in your drainage?
Also a larger bottom could be made to sit the planter on with 3-4" all the way around for polished rocks, marbles or rock chips. That way you can bottom water your plants.
Thanks again!
You are making far too much work for yourself! Here's a tip: First coat the inside of the bucket with silicone or WD40 or plain old cooking oil, before you fill it with cement. Then when the cement has hardened, spin the bucket over and pour boiling water over it, the cement pot will slide out nice and easy! :)
Also make a tiny hole in the bottom part. It will allow air in to release it easier
exactly
This is EXACTLY what I've been looking for.! Finally found a video that is easy to follow with awesome results. Thank YOUUUUU.
wow! this is the coolest video about concrete planters making! Thank you for such attention to detail, it's priceless.
You have some great BRILLIANT tips and tricks! THANK YOU! I need to find something to help supplement my income. I thought about concrete pots. But wasn’t sure. But you have worked out all the issues! I am so grateful. And you give such great instruction, without being too long winded!
Best ever tutorial on concrete planters...!
Often times when building forms for concrete you can add oil and that will make it easier to remove the forms and finish the concrete surface before it’s completely cured. If you change the oil on your car you can save it and use it for forms.
Does this stain the product?
Do you add oil to the concrete mix, or oil the plastic tubs?
@@kimmystardust6030 Have you ever tried to remove oil from a concrete driveway? Yes it stains it.
Thanks Moser. I ordered my supplies from Lowes while watching this video and printed out your template. Hoping to make a few later this upcoming week.
This is a well done video. Very thorough. I wish all tutorial videos where like this.
I’d definitely by the spacers if you ever decide to sell them. Great video. 😀
Your planters turned out great! They look awesome!😎 👏🏼 👏🏼 👏🏼
I’ve made about a dozen and I use inexpensive dollar store coconut oil or vegetable oil as a mode release.
It makes life so much easier!!🙂👍🏼
Do you just rub it around the buckets before hand
Yes.
A fair amount of it. Don’t skimp, a light coat won’t be as effective.
What is the name of the measurement tool you use to cut off the bottom of the buckets please? Awesome vid. Thanks so much!!!
I used a marking gauge (like this: amzn.to/3sMM0kJ), but honestly just using a combination square and marker would work just as great (and a combination square is a more versatile tool to have on hand).
You are a born engineer, my friend. Great job! :)
Awesome man thanks I've been looking for something to make planets with great work
And poring hot water can help loosen up the plastic and make it easier to remove 👍
Top tip: multicutter is the easiest way ive found to cut plastic. No cracking of the plastic and no nearly cutting your fingers off.
Amazing. Great video with lots of details to help you along.
Wow 🤩 seriously amazing video! Thorough and excellent use of your camera and editing!!! Loved the video as much as I (will) love my planters!
You don't need special things to hold the inner bucket.. Fill it with water, problem solved! also, I make these too and I don't cut my bucks at all because I oil the outside of the inner bucket as well as the inside of the outer bucket. The final thing I do is make a handle I can grab and use to release the inner container. I also drill a drain hole and hod it open with a piece of pipe. It's flush and it's oiled so it will come out when I pull it out from the bottom. It all works and I didn't cut anything.
These are all helpful and clever tips my man. Keep these coming.
I really appreciate your videos! Only watched two so far this one and the workbench build but they both were pretty top notch.
Good explanation of handy tips. Inspired idea for getting out the air bubbles. Excellent video!
THANKS FOR THE VIDEO. LOVE FROM KERALA
Using cooking oil spray allows for an easy separation thanks for the video
Great Video! Everything was so well explained and easy to follow. Gotta check out some of your other videos, my friend! This was so well done! Thanks for your time and effort!
You’re simply amazing and keep up the good work god bless you! Your video not only help me but it will help million others for sure 😊🙏🏾👏🏽
Curious about drainage holes? How/when would you add this?
Have you tried brushing cooking or motor oil onto your molds? Makes the release much easier .
Thanks for the video, very informative - I’ll definitely give this a try! Also, just wanna say that you’re a natural educator. You look pretty young, so I’m assuming it’s not years of practice - but seriously, you’re really good at getting your point across without me ever losing interest - and even more impressive is that when I thought myself a question about something, you were answering the question I had in the next segue Really impressive my man. Just sub’d, look forward to checking out your other videos, and I definitely wish you and your career choices all the best. Xiao
hey man this is a great job and well put together. Thanks for the template. Exactly what I was looking for.
This is exactly the video I have been searching for. Thank you.
Well done! You are an excellent teacher
Great technique! The wooden bucket clips are genius. Would bricks or sand in the smaller bucket achieve the same effect?
That's absolutely great man! Quick question, what's the name of the plant on the left side on 14:38 ????
I think it’s either a young Monstera Deliciosa without fenestrations, or possibly an elephant ear.
@@elizabethj238 Thank you very much!
Great looking planters. The base looks real high end. Definitely can use cheap cooking oil to alleviate sticking but fabulous problem solving, entire video and end product. ✨🫶👏🏼👏🏼👏🏼🪴
That was just amazing! I've never seen a better instructional video anywhere. Thank you.
Great video! I see how I’m going to spend the weekend!
nice job!! question: have you ever tried making the concrete just a bit less thick and then pouring? You could probably drill the holes 20 minutes later, yes this would make another place to tape, but as thick as you have it, I wouldn’t think any water or concrete would come through. Thanks for sharing. 🌿
great tutorial, how heavy did the end product with saucer come out to be?
Great video! I have an idea for part two! Do a search for dry pour concrete on youtube. All the trouble you are having with this project all involve wet concrete. If you dry pour, you won’t have any trouble at all.
Ha! Then you can do a comparison of wet pour vs dry pour planters to deal with all the haters.
Beautiful! Thank you. Please keep sharing 👏🙏
Good idea with the wood pieces! Never saw that before! 👍
Thanks! Very useful for a variety of applications.
If you put a soda cap in bottom makes drain hole.
Bro you don't need to cut the bucket. Just apply old engine oil on the inner surface of the bucket before pouring concrete mix. And after the concrete is set just invert the bucket and add boiling water on it. The heat will expand the bucket and the pot will fall off.
But your method looks really cool 🔥
Hi! Thanks for this tip, I’ve for sure seen quite a few people do this rather than cutting and taping the buckets. Just wondering what you mean when you say to “invert” the bucket? Do you mean that after you get the inner bucket out you flip the “outer” bucket upside down and pour hot water over the outside/bottom of the bucket and it will release? Hopefully you see my comment as yours was posted 6 months ago l😬
Thanks so much!!!!🤗
@@charliblake8551 Hi, yes you are right. Just turning it upside down and pouring hot boiling water on outer surface of bucket. Also few gentle strikes with a rubber mallet will help.
But removing the inside bucket could be troublesome sometimes.
Thats why I follow dry concrete mixture method to make pots. You can refer "how to make cement pots" from "urban gardening" yt channel.
Hope it helps 👍
Outstanding. Especially loved the alignment blocks. Wow!
They're beautiful!
Good idea with the precuts in the buckets!
Remember to wear gloves when working with any cementious material such a concrete because it is acidic and can cause skin problems.
Also, pre-made concrete mix is great but you can also make your own with a cement bag and aggregates of your choosing for more customisations and strenght!
Cheers!
Wow this technique is much smarter than what I tried to do 😅 Wish I would've watched this video first!
I would love the spacer template. Is it available for down load?
What’s the purpose of rinsing with water first and then seal? Thanks
Thank you for your video 😊 Can you recommend a sealer for the inside of the pot?
If you're worried about cutting yourself, there are gloves available that fit closely but have some steel filament woven through it. They help to prevent cuts. I use them when cutting up glass. I don't know how well they work as I've never cut myself but they're worth a try.
Very nice video. Very detailed and informative. thank you!!
LOVED your vid! Genius. Liked and subscribed.
Great instructions & insight!! So grateful! Thank you!!
👍🎖🏆🏅Excellent Presentation, Thank you for your detailed explanation for completing the DIY project, please do make more detailed videos to help people like me who are not good handymen.
hi! would you happen to know where I could purchase the alignment blocks online? I don't have a machine to be able to cut out the shape accurately. Any help would be super appreciated :) Thanks so much for the video btw! so helpful!!!
Can you use these for different size containers, great idea and love the video 👍👍👍
Great tutorial. Thank you 👌
Great demonstration, I learn a few tricks from you..well done…waiting to see more of your work.
These are awesome, you’re great at explaining 🔥🔥🔥
He goes into every detail👍👍👍
Excellent tutorial 👏🏻 Thank you!!
Use plastic or scrap around the smaller bucket. Stick a dowel in the center of the smaller bucket for a draige hole.
Excellent video... you did a great job!
you're brilliant man!! thanks for this!
thank you ...excellent video...I would make a rope pull for bottom of inner bucket.. dirll holes and loop twine or chord through two or for holes, making a handle to pull the bottom up
also filling that lower cap with stones makes it easier to keep from floating up ... get a "FUNNEL to pour in the remainder of the cement... I will be using this. except I will put my weep holes 2 inches from the bottom around the outside... long story.
Thanks for sharing your valuable ideas
Great
Would placing the smaller bucket into a trash bag allow you to remove the little bucket easier?
Beautiful work and thanks for the complete . I will to make this too
Great video dude. You have good info and nicely presented. Could show some projects you buggered up and more jokes.
Cheers
Mario
Thanks for the awesome vid, dude! I’m making some planters today!
Can you use cooking spray/oil instead of cutting the bucket?
how about putting oil in the bucket surface?
Those look awesome. I’ll have to try that
I’m sooo excited about this video
Reallly reallly great video!
Great tutorial!
🌎❤️🕊😊
😊 Hello!
Thank You So Much For Sharing Your Skills! This is my first time Watching You On UA-cam! I Love Your Ideas & Video. I hope you will make more different sizes of Planters .
God Bless.
Stay Safe!
1.Drill a hole in the large bucket 2.seal it with clay 3. place pvc piece in middle where small bucket will sit on. Pour concrete , weigh down small bucket let sit for 3 days. When ready remove clay from bottom of large pot and BOOM NO SUCTION !!!
Very clever technique . I also like how simple and modern the planters look👍
The concrete mix is sand and cement or it also has gravel in the mixture?
A great idea to create cement pots from recycled materials!!!!!
I will try it
Thank you so much 👏🏻
What good is a concrete drip tray when concrete isn't waterproof?