I didn’t think gimmicky bits (like Atomic and Bearing) would work in X until this video. It’s a very neat concept and I’d like to see them make a return.
I think most players do not want equalizing beys. Everything else you said is on point. In all seriousness, however, in my opinion, Takara Tomy creating a balance between old and new types of bits is good.
For my ONLY opinion, I do not agree adding bearing nor Atomic since there's a lot of Beyblade x Blades that are heavy and mixing these Parts in a future competitive play might making the meta so unfair unlike Burst tournaments, There's alot of bladers that still use Bearing parts since the Type Meta is unfair.
Blow is just taper. I mean look at how much wider flat tips are in general in x taper is just blow after it’s been carried over to x proportions (same with point being the x version of the fusion driver)
@@richardtaveras3593 basically if you think about it, the gears are in a position where they can align perfectly with the rails. By changing the height on the middle part, it doesn't alter how the gears interact with the rail. However if the bottom of the tip changes height, the gears will get affected and it might hit the middle part instead of hitting the gears
@@Thunderdransword here's an example. If you decide to cut off a bit of the driver like Flat to try and create like a low Flat. That won't work cause the gears no longer align with the rails and are more likely to hit the middle part than the gears itself
I didn’t think gimmicky bits (like Atomic and Bearing) would work in X until this video.
It’s a very neat concept and I’d like to see them make a return.
Why would they not work?….
Atomic still probably won't work as the purple ring is free spin, making it unable to use x dash
@@moomoo189 just make the ball free spin, with another layer cap to the gears
Variable with Beyblade X speeds would actually be amazing, imagine how fast the rubber would wear down
Imagine a Quest Bit. 😂
my man predicted Rubber excel
I think most players do not want equalizing beys. Everything else you said is on point. In all seriousness, however, in my opinion, Takara Tomy creating a balance between old and new types of bits is good.
If they would put BB drivers in X, fans would just complain about Beyblade X not being very original
OP Bearing would be possible for X just like all the other gens
Unless it's as tall as disc ball then it would be too op which is terrible for healthy gameplay
Bearings weren’t meta breaking in other gens… just burst because of the weight creep
This video predicted the new whale bey bit :O
you can probably launch a burst bey with volcanic in an x stadium and it would work completely like an x bey lol
For my ONLY opinion, I do not agree adding bearing nor Atomic since there's a lot of Beyblade x Blades that are heavy and mixing these Parts in a future competitive play might making the meta so unfair unlike Burst tournaments, There's alot of bladers that still use Bearing parts since the Type Meta is unfair.
imagine making the bearing bit concept into bearing drive from phantom orion lol
Part 2 please !! I like it
I’m a simple man I see unite I click
Blow is just taper. I mean look at how much wider flat tips are in general in x taper is just blow after it’s been carried over to x proportions (same with point being the x version of the fusion driver)
How can I get some of thouse tips for me
The BEYBLADE X bits are only concept arts
Just look at HMS Bey's running core all the gimmick are there but without the gear
Amazing
Awesome🎉
I don't think the bits that change their height is good. (The variable and nothing you said) It could ruin how the gears interact with the rails
Don’t low and high bits already alter height?
No the tip and the gears are unchanged it’s the ring in the middle that changes the height
@@richardtaveras3593 basically if you think about it, the gears are in a position where they can align perfectly with the rails. By changing the height on the middle part, it doesn't alter how the gears interact with the rail.
However if the bottom of the tip changes height, the gears will get affected and it might hit the middle part instead of hitting the gears
@@Thunderdransword here's an example. If you decide to cut off a bit of the driver like Flat to try and create like a low Flat. That won't work cause the gears no longer align with the rails and are more likely to hit the middle part than the gears itself
@@Applreminiscen Ik I’m talking about the part in between the tip and gears part and the shaft
BEANS
tell me what kind of black and pink this is beys
Ahh sweet if this really happened!!!