Best explanation on Failsafe with practical exercise. Keep making such videos. Looking to this video I want from you a solution to my problem. This is my story.I am using Radiolink pixahawk flight controller.I build it myself on S500 frame.intially I was using 3s lipo battery of 11.7 volt and it was working properly.Now I am trying to use 4S lipo battery of 5200 mah. Battery monitor is setup asper guidelines.But this drone trigger failsafe too early even battery is good. Hud shows Battery voltage 15.7. Failsafe i set at 14.8 voltage. Will you give me solution to this.
@karthikstechtime0910 Thanks my settings are same.But failsafe activation is premature.I am using Qgroundcontrol app as GSC. Is failsafe tab GSC enable RTL may be the reason for premature failsafe. again I need your help.
How do we come out of Failsafe? The failsafe was triggered and the failsafe on the mission planner isn't going and when ever we connect MAV link the ESCs starts to beep like anything and the motors also starts to spin on their own!
PLEASE HELP : Hello Sr, firstly Thanks alot by your videos. please could you help to me? I have all configured for RTL with radio off fail safe, all check in the computer and also with my radio, all seems work well, but when I switch of the radio it does not apear the red big letters message in the meddle that says ( FAIL SAFE , NO RC Receiber ) altough it appear down below in the rigth corner the fly modes where the system advise that RTL mode is ON, I think it is working all, but I have fear to make my first fly because I dont see this big letters in red about FAIL SAFE , NO RC Receiber
First, check the THROTTLE FAILSAFE parameter in the full parameter list to confirm that it is enabled and set to the action RTL. Remove the propeller, arm your copter, keep the throttle in the middle position, then power off your RC. Check the HUD on the mission planner for the displayed message. Ensure that you have a strong GPS signal during this test.
@@karthikstechtime0910 i would have set the drone for some mission(waypoints) and due to some reason the drone isn't able to follow the path , then how to switch to manual mode so that i can take the control of it. Is it that we have to do using the switch provided or else can we program in such a way that if it fails , it will immediately give the control
so informative karthik bhai thank you, i have learn alot from this video
Thanks.
Super ji... Thanks for sharing...
Welcome..
Good job, Karthik..
Is this will work with tradheli running arducopter 4.5.7 ?
Best explanation on Failsafe with practical exercise. Keep making such videos. Looking to this video I want from you a solution to my problem. This is my story.I am using Radiolink pixahawk flight controller.I build it myself on S500 frame.intially I was using 3s lipo battery of 11.7 volt and it was working properly.Now I am trying to use 4S lipo battery of 5200 mah. Battery monitor is setup asper guidelines.But this drone trigger failsafe too early even battery is good. Hud shows Battery voltage 15.7. Failsafe i set at 14.8 voltage. Will you give me solution to this.
Two voltage failsafes:
1. Low voltage, at 4S × 3.7V.
2. Critical voltage, set at 4S × 3.6V. Initiate landing upon activation of the first failsafe.
@karthikstechtime0910 Thanks my settings are same.But failsafe activation is premature.I am using
Qgroundcontrol app as GSC. Is failsafe tab GSC enable RTL may be the reason for premature failsafe. again I need your help.
Hi bro this Ranjith can you put a video for RTL for high wind fs
Thanks for this instructive video! Did you try failsafe with rally points?
Yes, that video is also on my list. Please check it out.
hi karthik , in cube orange using holybro power module there is no sensing current value and percentage . how to fix this issue?
docs.holybro.com/power-module-and-pdb/power-module/digital-power-module-pm-setup
Without data cable connect kaise hoga
How do we come out of Failsafe? The failsafe was triggered and the failsafe on the mission planner isn't going and when ever we connect MAV link the ESCs starts to beep like anything and the motors also starts to spin on their own!
Could you please provide more details about the issue you encountered with ArduCopter?
PLEASE HELP :
Hello Sr, firstly Thanks alot by your videos. please could you help to me? I have all configured for RTL with radio off fail safe, all check in the computer and also with my radio, all seems work well, but when I switch of the radio it does not apear the red big letters message in the meddle that says ( FAIL SAFE , NO RC Receiber ) altough it appear down below in the rigth corner the fly modes where the system advise that RTL mode is ON, I think it is working all, but I have fear to make my first fly because I dont see this big letters in red about FAIL SAFE , NO RC Receiber
First, check the THROTTLE FAILSAFE parameter in the full parameter list to confirm that it is enabled and set to the action RTL. Remove the propeller, arm your copter, keep the throttle in the middle position, then power off your RC. Check the HUD on the mission planner for the displayed message. Ensure that you have a strong GPS signal during this test.
how to connect the controller to ardupilot for manual operation?
Could you explain in detail?
@@karthikstechtime0910 i would have set the drone for some mission(waypoints) and due to some reason the drone isn't able to follow the path , then how to switch to manual mode so that i can take the control of it. Is it that we have to do using the switch provided or else can we program in such a way that if it fails , it will immediately give the control
@user-eh4gq4er5z You can cancel while flying in auto mode by flipping your mode switch twice (stabilize or althold or loiter)
@@karthikstechtime0910 oh ok, thank you ☺
Hi, thanks by respond
I did all this previously of my message, but this red big words not appear
There are no concerns. Is everything functioning properly?
hi this is harish iam building apm2.8 drone and iam facing issues in that how can i contact u sir?
karthikaeromodeller@gmail.com