Help Glen! Is there a setting on the Easy Start for infinity. We want to avoid the 120 min max setting. We have a camper with a separate thermostat but we don’t know the setting for the espar controller.
We have several of these in our trucks. But one unit will not go into dark mode after setting programs. Panel stay lit and 3 squiggly lines stay flashing. What’s up? Appreciate your help.
Have been searching a lot, and this is the best explanation on the operation of the Espar Easy Start timer that I've found. Thanks. I have the same timer you're showing in the video. I want to extend run time to the maximum 720 minutes. As you show in the video, I go to settings/workshop, advance through to 4.1 but there is no value and I can't change anything. There are two dashes beside 4.1 (not a number value as shown in the video). When I tap the lower right button to change the value, nothing happens. I'm completely stuck. Any suggestions?
I get a no signal from my H3 with east start timer. 3 wire from heater red brown and yellow. Connected to red brown and blue white in easy start timer. What did I miss? It won’t let me set run time in 4.1 service menu. Heater runs if I power the yellow wire up with power probe.
There is such a program clock in the motor home. It has an internal temperature sensor, but it does not switch off at the set temperature. Can you help?
My Easy Start Timer has 10 wires, but we only need to hook up three; RD/RD, BN/BN AND BU/WH/BUWH? You're saying to also hook up the yellow as well, is this right? I have the Airtronic L. If so, what do we do with the other wires, just insulate them?
If you can tell me the model number of your heater. On the sticker it will be a number that starts with 25-XXXX for example 25-2325. I can tell you if it's 12 or 24 volt.
Curran. In the video starting at 7:25 going to 8:25 it describes the #10 setting. If it is set for “On” the heater will come on at the time you set for the heater to start. If #10 is set for “Off” The heater will start before the set program time, with the goal to be to have the heater up to temperature and ready to go at the time you set. Check you #10 setting and if you’re still having an issue give me a call. Polar Edmonton 780-465-5068.
Thanks I matched yellow to yellow and became dirty fellow ...
Saved me a lot of hassle...
Thanks much! That number 10 setting info saved me! U da man
Yup me too. Mine was off, now works like a damn
Thnx for the great and detailed info. Wanted to check a setting and now i can.
Thank u so much for this video.
So much info really helped me out!!!
May I ask you how you secured the controller to the plastic? Some installers use sticky-backed tape or Hook & Loop. Thanks
thanks my setting where off that's why the heater woun't start got it now couldn't figure out how to change the language either lol thanks again
Help Glen! Is there a setting on the Easy Start for infinity. We want to avoid the 120 min max setting. We have a camper with a separate thermostat but we don’t know the setting for the espar controller.
You can change the run time up to 720 mins for when you run a program.
Can you do all the initial setups with the heater running? If not how do you power the control separately?
Do you know what may be the issue why the heater doesn’t turn on but the pump they pumps the coolant turns on ?
Ps: DE is Deutch as in German haha. NL is dutch as in from the Netherlands (my country)
We have several of these in our trucks. But one unit will not go into dark mode after setting programs. Panel stay lit and 3 squiggly lines stay flashing. What’s up? Appreciate your help.
Have been searching a lot, and this is the best explanation on the operation of the Espar Easy Start timer that I've found. Thanks. I have the same timer you're showing in the video. I want to extend run time to the maximum 720 minutes. As you show in the video, I go to settings/workshop, advance through to 4.1 but there is no value and I can't change anything. There are two dashes beside 4.1 (not a number value as shown in the video). When I tap the lower right button to change the value, nothing happens. I'm completely stuck. Any suggestions?
When you’re on 4.1 did you press the bottom right? It should show numbers.
@@glenlemke6252 Yes, I press bottom right and the 2 dashes next to "4.1" don't change, nothing happens.
Very informative,thank you
Great video
Would it be possible to see the codes with
This timer or it would be only with the pro version
Would it be possible to run through setting the temperature from the start of installation not on a programme as mine won't go past 6°c
Does the setting for 12 volt heater is different?
Which settings do you refer to?
I get a no signal from my H3 with east start timer.
3 wire from heater red brown and yellow. Connected to red brown and blue white in easy start timer.
What did I miss?
It won’t let me set run time in 4.1 service menu.
Heater runs if I power the yellow wire up with power probe.
Здравствуйте! Подскажите как отключить автозапуск ниже +5 градусов ? Она сама включается в холода, хочу отключить !
There is such a program clock in the motor home. It has an internal temperature sensor, but it does not switch off at the set temperature. Can you help?
The 2 options for temp are 360 F° or -273 C° which do you want it set on
My Easy Start Timer has 10 wires, but we only need to hook up three; RD/RD, BN/BN AND BU/WH/BUWH? You're saying to also hook up the yellow as well, is this right? I have the Airtronic L. If so, what do we do with the other wires, just insulate them?
Florie, the Airtronic L generally uses the Easy Start Pro timer.
@@glenlemke6252 My Hydronic S3 uses 3 wires only therefore I can not connect Easy Time Pro (has 4 wires) but only Easy Start Timer. Weird.
ontroller says no signal have the same unit as you show, wont allow me to get into any of the settings ?
Excellent!
How do I know if my heater is 24 or 12 volt
If you can tell me the model number of your heater. On the sticker it will be a number that starts with 25-XXXX for example 25-2325. I can tell you if it's 12 or 24 volt.
I have a couple questions about this heater how can i contact you
My Espar is flashing no signal when I set up , any clue what I did wrong
What model heater do you have and what controller/timer? How have you wired it?
That timer doesn’t work the way you have described.
If you set the timer at 07.00 and set heating time at 60 minutes, the heater starts at 06.00 hrs.
Curran. In the video starting at 7:25 going to 8:25 it describes the #10 setting. If it is set for “On” the heater will come on at the time you set for the heater to start. If #10 is set for “Off” The heater will start before the set program time, with the goal to be to have the heater up to temperature and ready to go at the time you set. Check you #10 setting and if you’re still having an issue give me a call. Polar Edmonton 780-465-5068.
How to reset codes.