Repair Treadmill Error Code E02 | Control Board Faulty
Вставка
- Опубліковано 17 жов 2024
- This video shows how to troubleshoot and repair treadmill error code E02 control board or motor faulty. If you find this video helpful, please subscribe to my channel. Thanks
Tools/Components:
1. Electrolytic Capacitor 470uF 450V - s.click.aliexp...
2. Resistor Kit 1W 5% - s.click.aliexp...
3. Screwdriver Set - s.click.aliexp...
4. Cutter - s.click.aliexp...
UA-cam: / mycreativ3
Facebook: / mycreativ3
Twitter: / mycreativ3
Blogger: my-creative-en...
Music:
Carefree Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0 License
creativecommons... - Наука та технологія
I had a similar treadmill and the problem was the same 220k 1w resistor. Even the board is different,the problem was the same.
Thanks a lot for the tip. Great work!
Hi guys in my case I had to replace de 450uF cap and a 1Mohm/1W resistor. And it works! Thanks for the video!
Thank you very much for your good video. I had exactly the same problem with E02 error and it was the resistor absolutely disconnected, replaced it with a new one and everything is working now. thanks again
What resistor may cause the problem?
can you teach what resistor can replace for that problem
1st of all, Thanks for the great video and great knowledge.
I got help from your video and found 1 MOSFET short circuited. I replaced that MOSFET but treadmill only worked for few minutes and again similar error-02 started coming. What else could cause this issue in circuit. Please advise.
I also found that previously my Transistor was easily traced and found out that it is short but this time, it is not short this time. MOSFET Product number is: IRF460.
Please advise @creative engineering.
Same problem bro
This is around 2 years ago after multiple times replacement of MOSFET. I increased the MOSFET rating and installed 1 with higher current ratings but issue kept coming on. Later on found that there was high friction between the belt and board which caused the burning of MOSFETs. Lubrication plus replacement of belt resolved the issue for me.
قد يكون الموسفت من نوع igbt واستبدلته بموسفت عادي ذو اطراف sdg او كان العكس واستبدلته بموسفت igbt ذو اطراف ceg
on a Buffalo with a Chang pcb M3218CE-2A motor stoops after few seconds. do you know the adjustment of the Torque. If I turn on the hex switch it stops directly.
Hi, MOSFET all good I changed the capacitor to just Incase still e2 error could it be cause my a bad treadmill dynamo ? If you have the time please advise me thank you
Brilliant thanks mat was looking just for this just need to know what MOSFETs to get it is a Evo helthstream 321t hope you can help me out cheers Eddie 👍
I had the error 02 change 40N60 igbt it’s short, change new one as soon as motor start ,igbt short . Happen twice.i don’t no what’s going on any help welcome thanks
قد يكون لايتحمل اضف igbt fgh60n60smd بشرط ان يكون صناعة ممتازة بجودة عالية
My Horizon CT5.2 was getting E1 error after running 5 - 15 minutes. Found out that it was speed sensor that was not aligned to the magnet properly. Aligned it and fixed the E1 issue on it.
Our treadmill works yesterday but after we cleaned, it shows E02... did we accidentally removed something?
How did you fix it?
I am a women and no man can help me with this. I ain't no technician either. I got E02 with 2 treadmills with not a year of being used. My other had all new parts changed everything and still same. What more can i check with e02 besides this? Any recommendation
I didn't want parts with this second treadmill because i kinda think it would be the same problem
Don't forget to say "Buy the parts from a trusted seller"
Counterfeit market is huge in these days.
Cheers.
Иностранные парни такие умные и умелые во всем, чего не скажешь о нашей стране....
Hi, took your advice and changed the MOSFET igbt, the treadmill now runs a little fast and I have no control over the speed, every thing else works no errors, can you help, thanks
What do you mean no control over speed?
@@MyCreativ3 hi, when I power up, the carpet turns faster than the 1kph shown on the monitor, I can change up and down but it makes no difference to the carpet speed, thanks
@@clivefletcher3645 Do you check speed sensor connection? Make sure cable is tightly connected properly. Critical part from monitor to control board and speed sensor to control board.
@@MyCreativ3 yes,i disconnected and it gave me error, reconnected ok, before my problem 02 it was ok. What do you think?
hi, its me again, ive had a closer look at the board and realised that there is another mosfet with a silicone case, exactly the same, hidden behind a large capacitor. ive tested it and it gives the same results as the new one. could it be faulty and creating the problem with the speed control? thanks
what is that PCB holder you have. I should get one.
pro'skit sn-390 pcb holder
I have just cleaned it yesterday now onwards showing EO2 and some times EO9 also what to do due to corona all shops are closed no technicians available
If possible can u suggest me best multimeter to puchase, I live in lndia, and Amazon works fine here.
For best quality is fluke multimeter
@@MyCreativ3 There're various types of the Fluke brand 114, 115, 140 etc. Are they all doing the same job?
My tredmill shows E00 on the screen.. Any idea?
Jaipur में कहाँ रिपेयर होगा?
HI pls help me, my problem, when I start button press on motor is start but 3 seconds and off. Treadmill seconds playing
There is sencer problem in your treadmill...
Umm....I better hier a person to do this...
hi sir .. I have tradmill mega6000 and it gaves me the same error E02 .. is it have the same meaning as yours ?!
Mostly all treadmill give E02 faulty should be control board faulty. From there, you need to troubleshoot each component
@@MyCreativ3 . con u give me any macanic no sir
Sir ,My Treadmill key board start key not working,,,,,what can I do!!!
U can use a push on push of button, place it separately, or use normal switch small one which is used in cars for switching on extra led on the car.
Bravo exillent job👍👍👍👍👍👍👍👍👍
सर मशीन 6 मिनट में चलते चलते बंद हो जाती है और उसमें एरर 04 होता है तो क्या करें
If i understand the probeme was in resistance ?
Yup.. the problem by replacing resistor
Thanks! The resisor 220kOhm was the only one problem with e2 error!
thanks
Bg mw nanyak beli rangkaian atau panel yg udh jadi pesannya dimana ya
Cb cari di shoope ato buka lapak
What is the error 4
will give it a crack if its the resister. it was working yesterday fine then stopped again .
Good information
I just bought one n was putting it together n it says E2
Error 6 what is the broblam witch check the parts
Motor overload or current limiting on board . Try troubleshoot step by step
Que signifie l'affichage E0 et E1 ?
I hate this sound 😢
I need to speak with mechanic,to solve my treadmill problem,pls make calll
My screen is hard to see
جيد
Error e01 ?
E0? problem
nice
Sir please apna number dijiyega kuchh personal puchna tha
સુરત માં રીપેરીંગ વાળા નો નંબર સેન્ડ કરો ને
My mom poured water on ours
Treadmill E 06
Untuk e6??
How E03
i am getting E01
I fixed it by tightening the belt
Op
Eorr
i am literally just a girl how am i supposed to know what any of this means
الي يريد يعرف عطل المشايهe1 E6 E7 يدخل على قناتي شرح وافي وبسيط
Hello my name is Thierno DIEYE from senegal. I have xxterra tr300 and the error is 503 . I don't know what is the problem