How to reset Exhaust Fluid Fault on 2014-2022 Ford F250, F350 6.7 diesel speed limited to 50MPH
Вставка
- Опубліковано 1 жов 2024
- Check out my social media!!!!!
Snapchat- / javin
facebook- / regzastar
Insta- / nietojavi
Tiktok-www.tiktok.com...
=====================================================================
Hi guys welcome to my channel i have been working on cars my whole life and now that i have accumulated tons of experience and knowledge i want to share it with you.
I upload new videos every week stay tuned!!!!
Thanks for watching, please like and subscribe and god bless you!!
Disclaimer: JVFIX assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. These videos are only for educational purposes and i am not responsible for ANY INJURIES OR ACCIDENTS, DO IT AT YOUR OWN RISK!!!
It's a crime Ford does this to people.
yeap it is
Thank our government not Ford or anyone else.
Thats our wonderful EPA...
I agree, typically the Government is the problem. However, Ford should have made the diagnostics and repairs open to all mechanics. As of now, Ford profits from the situation.@@jarrodkirkpatrick1300
Thanks for the video! This worked for me while in limp mode! No computer, idled on 3000Rpm with engine brake on until oil temp reached 220 or so and the warning went away. Cut off for 2 min then drove it up to 80mph. Thanks again! 2019 f250
no problem, glad it worked for you
You are so back and forth very unclear what to do you need to say 1 do this 2 do this 3 do this etc. etc.
The day after we bought our 2016 F250 6.7 black Beaty , we were driving cross country to another wind job and limp mode hit pulling a fifth wheel! Called our very knowledgeable finance guy/ cowboy salesman/ friend/family from Hereford Texas at Whiteface Ford Mr Paul E. Jackson ! In his very southern draw “ Did you stop and put diesel in it ? “
“Well yes! We’re in Colorado now!! “
He said “Well you Kansas sunflower ,…did you leave the truck running while you were putting the diesel in?”
“ As a matter of fact, we did ! It was too hot for the dog ! Had to leave the air on!”
He said “ Well not no mo !”
We had to pull over shut it down remove the battery positive and negative for about several minutes , connected them back up, started it up, and it reset itself!
Thank you so much this fixed my 2014 f250. I was stuck out of town worried but after watching your video it worked 100%. Super happy. No computer , did heavy accelerations + 80 mph freeway and went away while driving . Saving this video for future references.
glad it helped u out. thanks for watching
How long did you accelerate?
How can i fix this problem without a scanner?
Show what it says to do
@@ltdkitty
Delete))
Yeap pretty much if you live in other state rather than California
Ya tuve la troca acelerada por 40min y no alcanzo la temperatura de 440 bro ?? Alguna razón ? Nomas llego a 250
yo dure 2 horas acelerandola para que llegara a 450
This fix my truck today save me some money mine did this from sitting in my drive way for like 2 months
yea this one too was sitting some time
I just added DEF, filled the tank, and filled it up with diesel and did a system check on the console. Seemed to reset itself. Maybe I was just lucky.
yea these systems are very delicate with def level and soot levels too, kinda annoying sometimes
Mine jus popped up out of no where and my tank is full but i drove it down the road for like 20 minutes and then it went away
yea these trucks could be a headache sometimes
I have a2020 f350 it’s stuck at going 8kms I’m doing this as I type this out. If it’s doesn’t work the first time I’ll do it again
yea it takes multiple times to get it out of that issue
If it doesn't work, you might have a bad module. What are the codes
hey Brother, if my truck can't drive 80mph, my truck can move only idling. What is the best way for me? thanks for the video
best way to move is disconnecting the speed sensor that goes on the tranny and it will let u move but there is a risk that I could damage the tranny cause it won't shift good when u disconnect it and then start driving
@@JVFIXLLC ок i thought your speed on video was 50mph. I did the procedure, heated the EGT 14 to 450 degrees, turned off the car for two minutes, started it again, made sure the injector readings did not rise, then moved 5 mph, made 5 accelerations from 0 to 5 mph, put it in park and the car idled for 30 minutes, after that the error message still hangs, did I do everything right? or did I miss something somewhere?
@@JVFIXLLC repeat the procedure from what point? Should I heat everything up again or just start moving and try to speed up? What should acceleration look like from a complete stop or after starting to move, always keep your foot on the gas pedal and release the gas pedal and press it again?
@@JVFIXLLC ?
Sir, thank you for making this video. It worked like a charm.💯
thanks for watching glad it helped
La camioneta está en relenti en este momento si le hago un delete de catalizador cres que funciona bien?
si va estar mucho mejor
Buenas tardes. Have a question do you need the computer to reset it ? Or can it be done without the computer?
Otra pregunta before u idle for 30 mins, you said you have to accelerate it, how fast did you go or accelerate for ? Gracias in advance
the scanner won't reset it if you don't have any codes I used it to monitor the temperature and do it a bit faster. after the idle I went to drive it Normally but first I did some heavy accelerations for 10 or 15 times from 0pmh to 5mph.
will this work with a 2016 gmc duramx
yea it will
This worked for me also... i has a scanner and was able to watch the temp come up on the #14 egt and followed the ret of the direction. THANK U!!
yea with scanner everything is faster and more accurate to diagnose
Your videos have been helpful; thank you! Do you have the procedure link for this?
thanks. the steps are shown on a sheet in the video if u watch it at the beginning you can freeze the video and take a screen shot
Man I was the best video ever it definitely fixed mine the one I was working on and I thought I couldn't figure it out forever and ever but that worked for me thank you buddy
Trying to do this now, what year was your truck, I don’t have a computer tho, engine oil at 210 right now. What did you do exactly
Glad it helped, sometimes these trucks are a nightmare lol
leave your truck revved to 3000rpms for 20min and it should go back to normal, if not you will need a scanner to dig deeper into the issue
Thank you
no problem
That poor engine…
yeap lol
You realize that’s how these trucks are designed to run… right?
What work did they do?
Yo voy haciendo eso 5 veces y nunca se quita el engine idled, que estare haciendo mal? 😢
tienes codigos o no codigos?
I found 2 codes P207F and P0170, also the module nox12 wasn't updated. I ordered both noc sensor 11 and 12 and I will try again on Monday.
Great video
thanks for watching
Rehearsal makes better video
yea, thanks for watching
Thx🎉
thanks for watching
Does this work on the f550 10:06 10:08
yes is the same too
@@JVFIXLLCplz how i can do it with ford f-750 year 2013without computer
What if i am not getting any codes.?
you are getting the same message and no codes, is your def level ok
Will it come off when driving or after 30 min idle? Do you shut off after 30 idle?
it should, you can try just like I did on the video
This fix worked for me without a computer. Fast idled for about 25 minutes and got oil temp up to around 212 and followed the procedure. Had to do fast acceleration twice before it reset. Saved me some $. Thanks.
Glad it helped. thanks for watching
@JVFIX did you do it for 25 minutes bith times
Or 2nd time just get it up to temp and then turn off and
Got oil temp up to 212 both times. Took around 25 minutes both times.
Well clearly there is a computer in the video. So how was this done again?
i warmed up the truck 1 time cause it was a hot weather but if you live in a cold weather it will take longer
Buen video bro, ya estoy subscrito ojala sigas haciendo este tipo de videos, saludos desde mexico
gracias. saludos gracias por visitar el canal.
I have 2016 250 6.7 with def fault and limp mode don't know how to fix it you have any idea thanks
do you know what codes are you getting?
Will this work if your truck is in complete limp mode. Like only goes 5 miles an hour?
Thank you for your help
yea this truck was just like that. try it it
So i ran this procedure and after inlet it sit for two min and then started it again the injector jumped to 99% but the pump stayed at 0 and never came up and started dosing. Would you say the pump is bad?
Thanks! Was stranded just idled at 2500 and got trans temp up to 220 for 25 minutes! Light went off and I’m back on the highway! F350 2019
if you are not getting codes about the pump or Low pressure codes you should be good. did you get the truck already out of the speed limiting mode or is still stuck
Im getting a reductant pump circuit code now. But it does come out of limp when you do the reset@@JVFIXLLC