Shark Robot Vacuum Cleaner Front Wheel Removal | All Models IQ , Ion , AE
Вставка
- Опубліковано 5 жов 2024
- So lately I have been overwhelmed with people asking how to remove the front wheel of the shark robot vacuum cleaners. Some of them have broken the wheels before even watching any videos. I have made this video to help everyone understand what the difference in removing the wheels looks like depending on what mode you have. This process can take as little as 1 minute or as long as a hour depending on the mode you have. I also go over when you need to remove it and when you do not. With so many different modesl from IQ , Ion series 700 , 800 , 1000 there are different ways.
- Наука та технологія
Thank you, after watching your video I was able to clean my wheel and everything works happily now!
Feel your pain.... Thanks for all your help on these robots and hope things settle down a bit for you. Totally agree with you that eBay fees have gotten out of control!!
Finally someone that can understand. Thank you for watching
just discovered this guy, I like him he's cool. I'm just tearing apart my shark IQ to see whats inside
Thanks
Thank you for your exactness on this video 👍 so easy, and much better than the Shark manual.
You just gain a subscriber thank you my shark acting funny
If that little white attachment piece breaks and the wheel keeps dropping out, who can you fix it
Hi I need a full nosewheel assembly for a Shark RV2520A0US for some reason the nose wheel keeps falling out of the holder. I tried a new wheel but it seems that the holder has worn out....
Hello I have a Shark RV912S. The front wheel and the swivel with post came out. It falls out easily. To be clear, it is the wheel, the external black plastic snap assembly and the metal post. The post has a groove on the very bottom of the shaft. I can see the white plastic receptacle inside the robot. From your video, it is the type without the screws so it has the clip (or the screws inside).
What I want to know is...if I go inside and behind the motherboard etc, will I get the white plastic out and be able to snap the metal shaft back into the white plastic housing. It looks like there may be a snap ring for the bottom of the saft that holds it in the white plastic housing but it can swivel around. Did the shaft somehow slip off the snap ring and the ring is now stuck in the white plastic housing?
If I need to go behind the motherboard to get to it, is it better to replace the whole assembly? If so, where can I get it? This model is not common on the internet. Maybe there is an equivalent model number?
I'm standing by and hoping to hear back. Thank you.
nice, bro. thanks
Thanks! That was the exact info I was looking for!
Glad I could help!
Thanks for the help!
I have the AV2501AE, the one that has to be taken all the way apart to change that white wheel clip. Are you able to tell me what that part number is or where I can find the right one? I'm worried I'm going to buy the one that has the screws on top by accident. Any help would be greatly appreciated. Thanks for the video, it was very helpful, too bad I didn't watch before I accidentally broke mine trying to clean dog poop out of it 🤦♀️
I have the Shark IQ XL R105AE, the Dock light is blinking blue, the clean light is blinking red and the exclamation light is blinking red, (I think its error 21? I've tried restarting it multiple times but am unsure what's wrong with it
Thanks!
My AV2510AOUS is riding low in the nose and will not contact charger tabs because rear is high. Nose wheel spinning freely. Can assembly collapse? Or can wheel wear out and lose diameter?
They can wear out but its rare unless used on concrete. The back springs might have stuff stuck in them remove and clean.
@@SmittysWorld Spot on, sir. A dryer sheet had gotten into one of the wheel assemblies and would not allow it to compress all the way, thus lifting the rear. Thanks so much for your help
I need the front wheel assembly for the Shark 1000. The one you show in your video that should not be removed has fallen out and will not stay in. Will I be able to replace that myself
I don’t have any in stock right now the robot has to be completely taken apart in order to get the two screws out to drop it out
Do you have any videos on how to take apart a RV2001WRUS?
No but it’s very similar to be honest
@@SmittysWorld The pin broke where the fluid reservoir latches into the back of the robot and wondering if that piece can be replaced.
Any videos on how to make apart the 2 in 1 vacmops?
Hoping you have advice for me. My Shark IQ Navigation says my front wheel is stuck. It works smooth. Popped the front wheel out. Nothing in there. Wiped it down. Still won’t work. Think it’s the sensor?
Pulled out the roller brush and there was a horrific amount of hair there you can’t see without taking the roller out. It appears to be working right now again. Guessing/hoping I was getting the wrong error message.
@Rev Limit yes it worked.
How do I contact for parts?
How can I contact you? Need parts to fix my RV700_NC
I no longer sell parts
On a 1000 unit how much is the side brush motor
They are sold as a pair for $35 plus shipping. That’s if I have any left in stock
I did exactly what you said not to, I forced it out, and now it won't stay in. Do you have a part for this? Thanks.