Nice! I've never seen the inside of one of those. Looks like theres a lot more to it then I expected. Heres a quick question, how far beyond the crank shaft does the driver clutch protrude? Does it stick out more than the shaft itself? (obviously the bolt does) Just wondering if I have enough clearance for one of these. Thanks!
Tman: The weights are made of zink for a stock 30 series. Aluminum is available for some racing aplications. Best to use some wire wool and soapy water to scrube them clean then relubricate with Moly dry lube ( could use some wet inside the weight area but more cleaing will be required ). Block sand the clutch faces with some 120 grit if there is any wear or rust.
Hi great video, I was wondering if you had any ideas why my go kart will not engage and move forward. Do you think my torque converter is bad or just might to be cleaned? Let me know what you think thanks!!
When I take off from a dead stop my go kart jolts real bad, several times, like something slipping. especially with the extra weight of another person. Is it the torque convertor or do I need a new belt? is the torque convertor bad or can it be cleaned or repaired? Thanks very much.
I just got one of these manco carts with the 6.5 on it. Runs awesome but the thing wont go. the belt tightens and the toque converter slips? not the driver on top, it works fine, I just cant understand how these work. Could someone explain what my problem could be. I can twist the torque converter with my hand and it doesnt turn the sprocket.
i have a 30 series . on the slightest incline it wont go it start to wear the belt. on flat land it runs pretty good.i cleaned the drive pulley. i dont think it had a brass washer im going t double check that but the srings were dirty they didnt look stretched. can u help me?
i have a 30 series . on the slightest incline it wont go it start to wear the belt. on flat land it runs pretty good.i cleaned the drive pulley. i dont think it had a brass washer im going t double check that but the srings were dirty they didnt look stretched. can u help me?
Nice! I've never seen the inside of one of those. Looks like theres a lot more to it then I expected. Heres a quick question, how far beyond the crank shaft does the driver clutch protrude? Does it stick out more than the shaft itself? (obviously the bolt does) Just wondering if I have enough clearance for one of these.
Thanks!
Tman:
The weights are made of zink for a stock 30 series.
Aluminum is available for some racing aplications.
Best to use some wire wool and soapy water to scrube them clean then relubricate with Moly dry lube ( could use some wet inside the weight area but more cleaing will be required ).
Block sand the clutch faces with some 120 grit if there is any wear or rust.
@Tmansgokarts cool thanks, I saw it in the second part of your video, but I still couldn't tell for sure.
I usually use a sonic cleaner from harbor freight it works amazing! And all you need is dish soap and water
Hi great video, I was wondering if you had any ideas why my go kart will not engage and move forward. Do you think my torque converter is bad or just might to be cleaned? Let me know what you think thanks!!
When I take off from a dead stop my go kart jolts real bad, several times, like something slipping. especially with the extra weight of another person. Is it the torque convertor or do I need a new belt? is the torque convertor bad or can it be cleaned or repaired? Thanks very much.
@tmansgokarts. Do u have to have the brass ring I bought a gocart and it didn't come with one am I ruining it by not haveing one thanks
could you explain what a torque converter does? does it give it more power? or more speed? thank you
dude i need help i have a Yerf-Dog Go-Kart #3203 and i got a 11 hp honda engine and need a driver which one do u recomend not that expensive ...
Hey my driver don't come apart like that there are three hex screws on back is that why ? Should I take them out
Dude, I think my paper towels are softer than your toilet paper. I'm just messin with ya t-man, love the video. Hope you like my response!
Hey what are the dimensions of the brass sleeve?
I just got one of these manco carts with the 6.5 on it. Runs awesome but the thing wont go. the belt tightens and the toque converter slips? not the driver on top, it works fine, I just cant understand how these work. Could someone explain what my problem could be. I can twist the torque converter with my hand and it doesnt turn the sprocket.
Trust me u. Have to take the pull start off to tighten it do I learn hard way and it fell of and I lost spring brass broke had to buy another now
Old video but still helpful thanks !
+Cr125stin sure, I should do a remake of this.
Last video for tonight yawn but I wanna watch more :/
How do I get it off the engine whenever I try and take it off all it does is spin the shaft
U have to take the pull start off
i have a 30 series . on the slightest incline it wont go it start to wear the belt. on flat land it runs pretty good.i cleaned the drive pulley. i dont think it had a brass washer im going t double check that but the srings were dirty they didnt look stretched. can u help me?
MrOly076 what size of tires do you have.
Hey T-Man, where is part 2?
+GuitarGuys7299 .... opps.... ua-cam.com/video/cEQy_t_XDcM/v-deo.html
Awesome. Thanks T-Man
i have a 30 series . on the slightest incline it wont go it start to wear the belt. on flat land it runs pretty good.i cleaned the drive pulley. i dont think it had a brass washer im going t double check that but the srings were dirty they didnt look stretched. can u help me?