This is not bad. But it can only drive things like lamps and switch mode power supplys. The problem is that the frequency is much to high to drive a motor or other inductive load. A normal motor needs about 50hz to function correctly while this circuit runs at several khz. Still not bad bad.
Good job 👍 but Your inverter's FREQUENCY is 15 kHz, such a FREQUENCY can not apply to a Dan, freezer, TV and any appliances that use 50 hertz FREQUENCY. Its useful only for bulbs...
Sir i have made 12v to 40v dual rail power supply from your video , but sir the transformer is getting heat . Please help me , Please tell me the gauge or the thickness of wire you used for primary and secondary winding. (12v to +/- 40v ) But the circuit is working fine , only transformer heating , and please provide full video of transformer winding by which the viewer can learn full winding.
At the beginning good job ! I have question , 1. Why primary winding(2 + 2) are you winding opposed ? Some people say to wind bifilar method and it seems to me that bifilar method has the same direction winding . Maybe I am wrong ? 2. Why you do not winding bifilar method ? 3. Is it posible to change direction of transformer wires ? If you desolder two litz at transformer and put there transistors(GND) and wires from transistors connect together and connet to 12V. It will be works ?
Good work, the inverter am using today, I constructed it from one of ur videos, and its working perfectly. With this 2000w, how can I decrease the frequency to fifty Herz? Or if I want to construct 5000w, how can I go about it sir?
it is not possible!! but you can use a fast diode (and powerful) and a capacitor in order to get 300VDC. With DC, at this voltage, most of the devices will work. If you will not transform into DC, the diode bridge from the device could burn out or even the cables till the bridge..... and droselll...... if you want still want 50HZ , you have to make a mosfet bridge controlled by an Arduino and feed by 300 DCV. This is just an idea... an expensive one....
Boa noite eu assisto todos os seus vídeos só tem um porém não tô conseguindo fazer a montagem do inversor porque não tem o esquema e nem você está explicando como fazer passo-a-passo mas é excelente O que você está fazendo eu espero que da sua parte que você explique bem detalhadamente o que está fazendo e por gentileza fazer o esquema para fazer com que nós Montamos esse inversor mas meus parabéns é muito excelente os seus projetos Desde já agradeço muito e um bom fim de semana para você.
you should make a variable dummy load since you made so many inverters. nobody who makes inverters makes dummy loads for them. i know it sounds easy but from what i can tell almost none of the inverters people make are actually made to do anything and will have variable output voltage if given different loads. its like a incomplete circuit that lots of people show off but its less useful in its current form
Buongiorno. Complimenti per il progetto. Volevo realizzare uno simile. Potresti aiutarmi per costruirne uno con potenza costante di 1200w 50hz 230v.per alimentare una resistenza 1200w. Grazie mille.
That sounds like alot higher than 50/60Hz, that needs to be rectified and stored in a large cap bank, then chopped into a sine wave!! I guess it's OK to play with!
Hi Professor Please indicate how many amps do the battery consume? And can the output be used for welding electrode 2? Please insert circuit diagram Thanks
Please provide the formula of binding the core with wire and the gauge for high amp.. And one more thing, in the video, i see the black and red wire (positive side and negative side) both connected in negative terminal of the battery. where is the positive terminal of the this circuit???!!!
Mình gỡ trong biến áp cũ, cuộn sơ cấp 220V ấy, nó dùng dây đồng bé xíu màu vàng vàng ấy. Dây đó có lớp emay dễ nóng chảy, chấm mỏ hàn là cháy lớp emay cách điện rồi. ko phải cạo cách điện.
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing. thanks.
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing. thanks.
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing. thanks.
Perdão, mas não entendi muito bem para que serve tal circuito se alguém puder me explicar ficaria grato. Achei muito interessante a montagem e gostaria de experimentar mas só posso fazê-lo depois de saber o que é e para que serve. De qualquer forma Like pra vc amigão. Vlw parabéns
Hello, Please tell me. Instead of *Pulse transformer is EE55. Primary level 2 + 2 turns, 10mm litz wire. secondary 50 turn litz wire 1mm.* could I use another transformer? If possible, give the caracteristics.
can I use this circuit to excite a flybak? where can i put the signal from the frequency generator plate? hello sir i need an h bridge to connect the output of an oscillating frequency generator plate from 1hz to 150khz can you indicate? need a good powerful circuit to excite a flyback can indicate? I can use this circuit to excite a flybak where I can place the signal from the board
@@PhdHung if I use 2 , 800watts ec 42 firaat transformer for the same circuit then how many mosfet I need for en risister velue stay same or I must to be change risister value to up or down?
isso ai e uma maquina de solda pois pareceu que a idei e deichar a lus ligar pra ficar acesa nao como um pisca alerta deichar pelomenos uns 20 mn pra ver a reacao
Hy bro, i like your knowledge... i want to make efficient ups for my xerox photostat mechine 5855. its required load is, 12A, 1250 watt and 110-150 volt.... we are using voltage converter 220 to 110.... it can also work on direct 220 volts. i want to use this mechine on solar system.... guide me or teach me to make this...... i want to make a ups of 15A, 1800-2000watt and (110 and 220volt) output connection.... reply zaroor ki jiey ga......
Ese circuito esta entregando mas de de 220 voltios amigos, eso esta haciendo arco eléctrico si lo conecta a una lampara led las destruye de una,eso esta mal calculado...ojo!!!
Sorry sir .... can the transformer be replaced using a CT transformer (specifically for inverters) ... I have trouble finding transformer material ... thanks ...
Kay y project real mein kaam karta hai ....? Aapne kis Prakar tyar Kiya Hai Kya mospet number Hoon...? Diagram ke saat samjhao....? Hampi practical karke dekh le.....
ola homemade me ajude enterder quantas voltas tem osegundario na descriçao vc dis 50 voltas mas eu vi que vc enssolou somente 13 voltas me corrija se eu etiver errado ate mais e obrigado
No matter what, Thai people have never lost any nation in the world. One strong heart from Thai people
he is vietnamese :))
sorry but this man is Vietnamese
If you pass current through the inductor on the plus, it will not make noise, whistle.
Instablaster...
Good idea.. i think this inverter only work on fluorescent lamps because of unknown Herz.
That only fluorescent lamps can work
This is not bad.
But it can only drive things like lamps and switch mode power supplys. The problem is that the frequency is much to high to drive a motor or other inductive load.
A normal motor needs about 50hz to function correctly while this circuit runs at several khz.
Still not bad bad.
You're right
It seems very powerful and interesting please send me circuit diagram.
ok bro
Good job 👍 but Your inverter's FREQUENCY is 15 kHz, such a FREQUENCY can not apply to a Dan, freezer, TV and any appliances that use 50 hertz FREQUENCY. Its useful only for bulbs...
Sir i have made 12v to 40v dual rail power supply from your video , but sir the transformer is getting heat . Please help me ,
Please tell me the gauge or the thickness of wire you used for primary and secondary winding.
(12v to +/- 40v )
But the circuit is working fine , only transformer heating , and please provide full video of transformer winding by which the viewer can learn full winding.
At the beginning good job !
I have question ,
1. Why primary winding(2 + 2) are you winding opposed ?
Some people say to wind bifilar method and it seems to me that bifilar method has the same direction winding . Maybe I am wrong ?
2. Why you do not winding bifilar method ?
3. Is it posible to change direction of transformer wires ? If you desolder two litz at transformer and put there transistors(GND) and wires from transistors connect together and connet to 12V. It will be works ?
how long is the battery life? That is, how long it takes for your device to run out of power and battery voltage ?
Good work, the inverter am using today, I constructed it from one of ur videos, and its working perfectly. With this 2000w, how can I decrease the frequency to fifty Herz? Or if I want to construct 5000w, how can I go about it sir?
it is not possible!! but you can use a fast diode (and powerful) and a capacitor in order to get 300VDC. With DC, at this voltage, most of the devices will work. If you will not transform into DC, the diode bridge from the device could burn out or even the cables till the bridge..... and droselll...... if you want still want 50HZ , you have to make a mosfet bridge controlled by an Arduino and feed by 300 DCV. This is just an idea... an expensive one....
👌👌awesome. Also please make a video about calculation ferrite transformer.🙏
OK, I will upload to the FB group
@@PhdHung thanks
@@PhdHung have you done this?
Boa noite eu assisto todos os seus vídeos só tem um porém não tô conseguindo fazer a montagem do inversor porque não tem o esquema e nem você está explicando como fazer passo-a-passo mas é excelente O que você está fazendo eu espero que da sua parte que você explique bem detalhadamente o que está fazendo e por gentileza fazer o esquema para fazer com que nós Montamos esse inversor mas meus parabéns é muito excelente os seus projetos Desde já agradeço muito e um bom fim de semana para você.
Sorry, my english is bad. If I speak, surely people won't be able to understand :)))
you should make a variable dummy load since you made so many inverters. nobody who makes inverters makes dummy loads for them. i know it sounds easy but from what i can tell almost none of the inverters people make are actually made to do anything and will have variable output voltage if given different loads. its like a incomplete circuit that lots of people show off but its less useful in its current form
Is it inverter or welding machine make noise like TV lot is it works
IRF3205 is 110A rated. Is it necessary to use 6 parallel in half of the circuit ?
good job
Thanks
Buongiorno. Complimenti per il progetto. Volevo realizzare uno simile. Potresti aiutarmi per costruirne uno con potenza costante di 1200w 50hz 230v.per alimentare una resistenza 1200w. Grazie mille.
Yes, with high quality current requirements. you need oscillator IC and mosfet driver ic. Cannot use ZVS circuit.
Grazie per avermi risposto. Ho un trasformatore da 2000va e dei IRFB 4610. Vanno bene? Li ho recuperati da un vecchio ups.grazie ancora
Bhai aapne 1500W bola h to 1500w load Dalo❤️👍👍👍
That sounds like alot higher than 50/60Hz, that needs to be rectified and stored in a large cap bank, then chopped into a sine wave!! I guess it's OK to play with!
Dipankar Bal
Is that winding wires are insulated ❓
yes
All is good.. But wire colours opposite red wire used as negative
:D
In electronics usually use red wire for positive terminal but in electrical use red for live wire(line to ground)black wire for neutral line..
Hi Professor
Please indicate how many amps do the battery consume?
And can the output be used for welding electrode 2?
Please insert circuit diagram Thanks
About 130 Amps
It would've been better if you verbally explain the value, voltage or amperage of the different parts you are using. .
ok bro.
I would appreciate it if you make the video of 5.000 watts and 10.000 watts inverter, thank you
Kya ismein 50 cycle out hogi yah to hai per kaun si lagti hai jyada ismein koi bhi fen nahin chalega
This looks like a zvs driver without the fast diodes. How long did it last?
This circuit uses a resistor divider. It does not need a diode.
@@PhdHung what's the frequency? 50khz? I was wondering if it can drive a Tesla coil.
Parabéns amigo merece like
thanks bro
Please provide the formula of binding the core with wire and the gauge for high amp..
And one more thing, in the video, i see the black and red wire (positive side and negative side) both connected in negative terminal of the battery. where is the positive terminal of the this circuit???!!!
can I run my pc + LCD monitor + small size woofer speaker with your made inverter ?
no bro.
Obrigado meu craque gostei muito do teus trabalho força ai
?
Great work.can you please make a simple welding inverter video...
OK, wait
( Brazil) gold tanky you .
Thanks from homemade102
YOU ARE CRAZY !
anh ơi, anh có thể cho em biết là dây quấn biến áp như anh mua ở đâu không ạ, em tìm mãi mà không ra
Mình gỡ trong biến áp cũ, cuộn sơ cấp 220V ấy, nó dùng dây đồng bé xíu màu vàng vàng ấy. Dây đó có lớp emay dễ nóng chảy, chấm mỏ hàn là cháy lớp emay cách điện rồi. ko phải cạo cách điện.
@@PhdHung nếu dây mềm mà nhiều sợ nhỏ như vậy mình mua có không vậy anh, tìm trên aliexpress mà hổng ra
1500w/12v= 125A equivalent to #1 wire size... can u used all that amps with your design sir?
我也不相信有1500W
is the wire you winded into the transformer is the pre-enamel coated winding wire or is it the cable we know
I use Litz wire, you can find more information on google, It is best for pulse transformer.
Hello brother, the link does not open. Can you share the scheme of this circuit as drawn.
Thanks, I will use a nice project.
ok bro
@@PhdHung thanks bro
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing.
thanks.
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing.
thanks.
Hello brother, I am waiting for you to share the circuit diagram of the project, I will set up the circuit. I could not open the link, I can install the open circuit diagram and if you draw the components in the drawing.
thanks.
Perdão, mas não entendi muito bem para que serve tal circuito se alguém puder me explicar ficaria grato. Achei muito interessante a montagem e gostaria de experimentar mas só posso fazê-lo depois de saber o que é e para que serve. De qualquer forma Like pra vc amigão. Vlw parabéns
Sir can we run a high frequency ferrite core winded transformer with only mosfets without ic???
of course. Use zvs driver
But u didn't use that for driving that transformer why???
Can I make it with 12 volt transformer? I'm confused about your handmade transformer.
Can this be connected to house .. to give supply for 3,4 bulbs and fans..How much time will this provide supply i am having a 12v 65 Ah car battery
The frequency of this circuit is very high. You should choose a 50hz inverter in my video list.
Hello,
Please tell me. Instead of *Pulse transformer is EE55. Primary level 2 + 2 turns, 10mm litz wire. secondary 50 turn litz wire 1mm.* could I use another transformer? If possible, give the caracteristics.
Yes, but what is your transformer size?
@@PhdHung Thanks. I would like to say if I could use any transformer eg. 12 - 0 - 12V DC to 220V AC/ 5 or 10 Amp.
Extraordinarily good video. I congratulate. How to do it for 60hz?
Sir can i use different numbers of mosfet plz sir tell me ?
yes bro.
No sir imean i take 4 mosfets 2 another number and 2 another use 4 mosfets for inverter
Nice job
Thanks bro
hi brother u said secondry wire 50 turn but i see ur turning only 15 turns only
very good go on.
Perfect
Большой ток потребления,не целесообразно так делать, только лампочки зажигать,tl494 или ir2153 с повторителем и будет норм .
can I use this circuit to excite a flybak? where can i put the signal from the frequency generator plate?
hello sir i need an h bridge to connect the output of an oscillating frequency generator plate from 1hz to 150khz can you indicate? need a good powerful circuit to excite a flyback can indicate? I can use this circuit to excite a flybak where I can place the signal from the board
Good tiçhing 👍👍👍👍👍👍👍👍👍
Can I use EC42 800watts feirat transformer for this circuit?
yes
@@PhdHung thnku very much sir
@@PhdHung if I use 2 , 800watts ec 42 firaat transformer for the same circuit then how many mosfet I need for en risister velue stay same or I must to be change risister value to up or down?
Is it possible for water pump ?
the transformer did you use is available in market??
Esse corta aço blindado irmão potencia máxima mesmo valeu amigo parabéns gostei
isso ai e uma maquina de solda pois pareceu que a idei e deichar a lus ligar pra ficar acesa nao como um pisca alerta deichar pelomenos uns 20 mn pra ver a reacao
Hi my friend. Which a file number you refer to in the description please mention it. Thanks
It is very simple, so I do not draw diagrams. Please review the video, you will know how to connect the components
@@PhdHung transistors connection is not easy to trace brother, just make I simple schematic diagram thank you
Will it be ok for a 60 ah battery and to charge 4 laptops
Ab shert👕 utar ke kam kar rahy thy ??
Hy bro, i like your knowledge...
i want to make efficient ups for my xerox photostat mechine 5855.
its required load is, 12A, 1250 watt and 110-150 volt....
we are using voltage converter 220 to 110....
it can also work on direct 220 volts.
i want to use this mechine on solar system....
guide me or teach me to make this......
i want to make a ups of 15A, 1800-2000watt and (110 and 220volt) output connection....
reply zaroor ki jiey ga......
cái này thiem mạch bam xung vào làm kích cá được ko vậy?
Very nice like
Very nice👍
Cấp sai nguồn và cái kết đi 2 dàn fet. Nhà đã hết quỹ r mà đen quá :D
Does a power supply adapter work?
Your connections of S,D,G are not the same of datasheet of IRF3205 as you make in the vedio!!!!!
ESTO PUEDE MOVER UN MOTOR DE LAVARROPAS PARA UNA BICICLETA GRACIAS
Ese circuito esta entregando mas de de 220 voltios amigos, eso esta haciendo arco eléctrico si lo conecta a una lampara led las destruye de una,eso esta mal calculado...ojo!!!
El arco es por la potencia recuerde que son 1500w de salida
We can use 60 watt nulb this circuits? ?
yes.
Homemade 102 for how long
Can I use UPS Transformer ..?
theks bradhar,diagram plz I riqwest...
very good thank you
Make me your student teacher 👍👍
You didn't mention any clear description of the components used. I think your your current s not steady.
Could you tell me where can I buy copper wires for inductors?
Sorry sir .... can the transformer be replaced using a CT transformer (specifically for inverters) ... I have trouble finding transformer material ... thanks ...
You can try, I think it works well
Can I use IRFZ 44 for MOSFET?
yes
@@PhdHung thanks so much bros
Olá posso usar mosfet irf 630 no lugar do 3205.obrigado
Please can you used big transformer for this circuit?
hi very good the video I would like to know if I can do it with a microwave transformer greetings from Peru
I am not sure. Do you have pictures of it ??.
Brapa lma kekuatan nya klo buat lmpu aja bos
hi guy, can you please provide it for me please, I just need the inverter without battery, how to reach you?
Hi...
The file not work in my phone...
Please send the circuit diagram....
That's excellent
Lấy dây 1mm thay thế cho 10mm đc k ban..😁😁
I need inveter like12vdc to220vac 5000watts can u guide or help I am india
Ok bro
bộ này chạy cho máy bơm 1.5 hp được không a
ko nhé
Kay y project real mein kaam karta hai ....? Aapne kis Prakar tyar Kiya Hai Kya mospet number Hoon...?
Diagram ke saat samjhao....?
Hampi practical karke dekh le.....
Its just blaster
Irf3205,44n,840n,520n,530n,48n...
Circuit base is heater induction.
it is ZVS driver
aawaj karke kaun kaun se component lagaa he sab bolke dikhaaiena
ola homemade me ajude enterder quantas voltas tem osegundario na descriçao vc dis 50 voltas mas eu vi que vc enssolou somente 13 voltas me corrija se eu etiver errado ate mais e obrigado
Is pure sine wave?
Can i use this for fish stunner?
is this sine wave?
No :)
Homemade 102 then what it is...?
how u count there turns i no understand brother help me
Ko dám đấu luôn cho mạch chạy lâu dài à ?
Ok felicitari
Amazing Brother....I have never seen such a powerful inverter, Can you make complete inverter with all features using this pulse transformer.
yes, wait me
What is this Belding machine?
Sir can i use it to run a printer reply must
No :D