I have the same one coming. I’m an experienced metalsmith, well versed with oxy-acetylene, oxy-propane, oxy-air and propane-air and soon, a water torch. According to jewlery websites one should add denatured alcohol and some flux into the bubbler. The denatured alcohol allows you to see the actual length of the flame and the flux helps the solder to flow. Really good overview of the torch and the comments in the comment section are also helpful. I can’t wait to try it on gold and silver. And I’ll be glad to get the big tanks out of the house.
You should use 150 gm of KOH and use the largest orifice that will work. The bottle in the front should be filled with methanol. That will produce a bigger flame that is useful for brazing. Without the methanol, the torch is useless because the flame is so hot that it burns the surface of the metal.
The warning sticker on top says to not open the fill cap when machine is pressurised. Also do not light when gas pressure is low. Your initial issue is not measuring the electrolyte (KOH or caustic soda) to the correct ratio. I own this machine and it lasted about 5 years before it simply stopped working, assumed electrode failure because only air was coming out . My newer machine is about 9 years old and still runs great which is the bigger model H260
@@mikeharmon4901 troubleshoot first getting the Koh mix ratio correct, I think 15% is right but refer to the manual. After this check the ammeter is reading around 10-12 amp draw and lastly take the flame tip nozzle off and look thru it to see it’s not blocked , if it is obstructed then use a small safety pin to clean it out then make sure it’s tightened back on properly before use or else flashback can happen causing hearing loss and a minor form of shellshock. Adhere by safety guide in the manual provided and you’ll enjoy years of reliable use from a hongguang oxyhydrogen machine
I have the h260 as well. It’s from…?? 2017? The relay went out that shuts its off when it’s reached the pressure limit. Some said they could fix it…. And they merely bypassed the relat so now it’s super sketchy and just keeps building pressure unless in Have the torch fully turned up. I use a knock off smith little buddy?? Torch or whatever it’s called. I have one of the two gas lines attached to nothing. This actually works in an interesting way and allows for more Flame adjustment when you open the side with no air flow. It softens the flame. I dunno were to get new relay /electronics for it :/
We just got this exact model. I'll deal with it tomorrow. But I didn't see the actions that says in the manual. For 1L of water , must use 150 g of NaOH. Make the mixture in a glass recipient, stir and wait 10 min.
You have to read the manual. I made a similar mistake before myself. You have to use Sodium Hydroxide Solution 15% (850ml water + 150g Sodium hydroxide) ... btw Never touch it with your bare hands because if there is any moisture on them, you will get burned on that spot.
Your not using enough baking powder, distilled water isnt conductive that is why u need to add the powder and the more u add the more conductive it becomes and ur amperage goes up therefore increases your pressure much faster
That is generally true, but I think this machine limits the current (I'm not sure). In other home made generators a tiny amount of KOH made a large difference, but not in this case.
To clarify, 25% volume of the dry and wet to one another? Measure one quart of the dry flake electrolyte to three quarts of water for a 25% mix? Do you use distilled water in both the mix and overflow?
The only problem I have with it is safety, HHO does not really exist, what we have is an explosive mixture of H2 and O2, you have a classic fuel and oxidizer mixed together, really the machine should separate both gasses and then remix them in the torch.
This is a type of torch/generator that has been used for literally decades. It was literally the first gas mixture ever used for welding (and the gas produced by electrolysis exactly like this). I assure you, as long as you have a flashback arrestor (the bubbler), it is completely safe to operate assuming all other safety precautions are followed. Absolutely no reason to separate the gasses and remix them. It would just add unnecessary cost and complexity. However, unlike what furulevi stated, it really isn't THAT complicated. It is just a matter of separating the anode and cathode into two separate tanks connected by an electrolyte bridge. Oxygen is formed at the anode, hydrogen at the cathode, already separated with no further work needed. However, even that is simply unnecessary for an application such as this.
@@furulevi Erm no... You just put a tube around the negative terminal for one gas, and the positive for the other. That's secondary school level basic science. A hydrogen fuel cell works in a very different maner.
On a much larger home-made HHO generator a tiny amount of KOH significanty increased the current consumption... This must be current limited (I haven't looked inside it yet).
I have the same machine and you need to add natrium hydroxide to the water tank. This is very important to give the water enough conductivity and the machine will produce more hydrogen gas . I fill the flame arrester / bubbler with water but you can add a small amount off pure alcohol. I believe in the paper that comes with the machine they say 1/3 alcohol then fill the rest with distilled water . The machine will draw around 7 amperes if the solution of water and natrium hydroxide is good. The machine works great and produces a really hot flame. But i would like it to produce more. If i had known i would have bought the 250 model because it has 2 hydrogen generator. But you can do a lot of soldering with this machine 👍😀 I even do brass welding with flux on small parts and it works well 😀. Just don't expect to much if you do bigger stuff . Don't throw away your oxygen/ acetylene burner is my suggestion 😂
You made a mistake with the metal wire. It mustn't get so hot. If it gets too hot, all the carbon in the metal wire burns up. Excessive flame may only act briefly. Too long exposure to the flame will burn the steel. This is very tricky and not so easy to set the correct temperature. Remember HHO flames are much hotter than normal flames. And there are other physical properties. You can easely melt stones with HHO
Hi, i recently bought these machines. My bubbler did not come with a pre-assembled pipe as shown in 3.07, it came separate with an additional pin arrow and spring. i think it serves as a one way value to protect against flashback. im sure that you will also have these if you remove this pipe. i want to know which direction i should i connect this? Pin arrow pointing towards the pressure guage (upwards) or away (downwards)? My instinct says towards the pressure gauge (upwards) so it serves to shut of the air from hho generator tank if there is increased pressure in the bubbler from for example a flashback. However, i couldn't find anything in the instructions/manual. Any help appreciated. Thanks. Ash
@@ghostlee900 i am stupid, please help? Are we measuring the weight of one to the volume of another? Would one quart of flakes and three quarts of water equal a 25% mix? Are you using distilled water in both the overflow and the primary tank?
Secondo me,dopo più di un anno potresti anche farci vedere dentro cosa c è, secondo me faresti un bel po' di visualizzazioni. Fino ad adesso non l'ha fatto nessuno. Comunque grazie del video!
I also have the same one, but the model is H160. I think your HHO flame is too small. My HHO flame is 10cm long. Check your NaOH: H2O is 1:5 and check if there is any air leakage.❤
Devices work without any problem if grounding is not present, that' just a safety feature. The cable shown at 0:13 has 3 wires, phase, neutral and grounding. At 3:38 the wall socket had no grounding.
@@furulevi Oh, I see . Its different than US plug, US plug has a grounding rod that sticks out from the plug instead of a hole . I just watched a video with the same model as you and I that had ten times the flame and the person I bought from said to use 250 grams of sodium hydrochloride lye . Good luck.
You need more koh, but not too much, if you put too much then you will need to wash out. Can you open generator? I want to see quality inside of it, thanks.
Pour 1KG of distilled water with .2KG caustic soda powder, stir allow 20 mins to cool. 5 to 1 is the example, 35 ounces distilled water with 7.05 ounces of caustic powder. You will create a very powerful mixture that will create a flame to burn through half the stuff your video showed couldn't. You did not have the correct ratio in your drum of the machine.
Well I definitely won't be buying one of those. Thanks for the tip! Just get a AC/DC TIG welder as you can weld pretty much anything with one of those (You can do most metals with just a DC TIG but you need AC for doing Aluminium (NOT aluuuuminium) and magnesium. Might be some others but I'm pretty there the main two). Especially if it's HF as it makes life a lot easier, even if you've got a lot of experience. Otherwise there will be a lot of tungsten sharpening n if it's thoriated it's even worse! Try your best not to breath in tungsten dust as it's not good for you, like most exotic metals.
This is extremely dangerous the way you designed this.. You need to seperate the gasses FIRST and store them that way, if you do not separate O2 and H you are going to end up with a flame that travels right back up the tubing and into the storage tank... hot potassium hydroxide everywhere not good! I've seen this. You can reduce the chances of it by creating a mesh based flame arrestor inline, but ideally separate the gas at production.
This was bought, not made at home. These devices don't separate the 2 gases, they don't have a separator membrane like fuel cells. The bubbler is the flame arrestor, a mesh type arrestor has no chance of stopping this gas.
@@furulevi Whether it was bought or made doesn't matter, this is dangerous. The bubbler doesn't protect anything, the gasses bubble up are O2 and H premixed, the flame can and sometimes does travel up the tube. They should be separated and its hard to believe these are sold this way!
We have used the ua-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
The flame is not too small, it is mostly invisible, at around 22:09 you can see that the paper is bending because of the heat of the flame, and at 22:12 it is even burning the paper.
I am surprised how small flame your torch produced at 1,5 bar . I use my own torch and when pressure is anything around 0.1 bar flame is almost 10 cm . Just saying you are better off buying generator .
The flame is not too small, it is mostly invisible, at around 22:09 you can see that the paper is bending because of the heat of the flame, and at 22:12 it is even burning the paper.
The flame size depends on the nozzle diameter. You can simply drill it wider to get a bigger flame. Of course you will consume more gas than you produce, so ...
The low amperage I think is due to incorrect NAOH / KOH mixture. Distilled water will carry NO VOLTAGE> Also your unit has a pressure gauge where another I saw has a "pop-off" valve in it's place and describes the canister it sits on as a "Blow-back flame arrestor" Filling it with methanol would be not to smart I am thinking. ua-cam.com/video/rD8XyicU_bo/v-deo.html
The larger one is far more expensive. The issues I see is this is only half decent if you use the alcohol. The other thing is that you have no way to increase the output, of you could control the amperage then you could increase the hho has output
What a time waster. Hope he has all his fingers till now. No need to read instructions of a device when making a vid. He knows nothing about chemy, use of psa, brazing...
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
I have the same one coming. I’m an experienced metalsmith, well versed with oxy-acetylene, oxy-propane, oxy-air and propane-air and soon, a water torch. According to jewlery websites one should add denatured alcohol and some flux into the bubbler. The denatured alcohol allows you to see the actual length of the flame and the flux helps the solder to flow. Really good overview of the torch and the comments in the comment section are also helpful. I can’t wait to try it on gold and silver. And I’ll be glad to get the big tanks out of the house.
You should use 150 gm of KOH and use the largest orifice that will work. The bottle in the front should be filled with methanol. That will produce a bigger flame that is useful for brazing. Without the methanol, the torch is useless because the flame is so hot that it burns the surface of the metal.
The warning sticker on top says to not open the fill cap when machine is pressurised. Also do not light when gas pressure is low. Your initial issue is not measuring the electrolyte (KOH or caustic soda) to the correct ratio. I own this machine and it lasted about 5 years before it simply stopped working, assumed electrode failure because only air was coming out . My newer machine is about 9 years old and still runs great which is the bigger model H260
I think the unit is bad myself? one watt? Unless his mixture which is very light on the KOH could be causing it?
@@mikeharmon4901 troubleshoot first getting the Koh mix ratio correct, I think 15% is right but refer to the manual. After this check the ammeter is reading around 10-12 amp draw and lastly take the flame tip nozzle off and look thru it to see it’s not blocked , if it is obstructed then use a small safety pin to clean it out then make sure it’s tightened back on properly before use or else flashback can happen causing hearing loss and a minor form of shellshock. Adhere by safety guide in the manual provided and you’ll enjoy years of reliable use from a hongguang oxyhydrogen machine
I have the h260 as well. It’s from…?? 2017? The relay went out that shuts its off when it’s reached the pressure limit. Some said they could fix it…. And they merely bypassed the relat so now it’s super sketchy and just keeps building pressure unless in Have the torch fully turned up.
I use a knock off smith little buddy?? Torch or whatever it’s called.
I have one of the two gas lines attached to nothing. This actually works in an interesting way and allows for more Flame adjustment when you open the side with no air flow. It softens the flame.
I dunno were to get new relay /electronics for it :/
We just got this exact model. I'll deal with it tomorrow.
But I didn't see the actions that says in the manual.
For 1L of water , must use 150 g of NaOH.
Make the mixture in a glass recipient, stir and wait 10 min.
It is possible to use isopropyl alcohol instead of methyl? Also using bidestilled water instead of destiled water?
You have to read the manual. I made a similar mistake before myself. You have to use Sodium Hydroxide Solution 15% (850ml water + 150g Sodium hydroxide) ... btw Never touch it with your bare hands because if there is any moisture on them, you will get burned on that spot.
Your not using enough baking powder, distilled water isnt conductive that is why u need to add the powder and the more u add the more conductive it becomes and ur amperage goes up therefore increases your pressure much faster
That is generally true, but I think this machine limits the current (I'm not sure). In other home made generators a tiny amount of KOH made a large difference, but not in this case.
@@furulevi hmmm probably the power supply that converts the AC into DC isnt big enough, I believe that one is only 300 watts.
Far away from baking powder...
@@marcopruscini1603 A specific Alkaline solution would be ideal but...
@@bitrage. Sodium hydroxide
you have to adjust the electrolyte in a range of 25 to 35% WT of KOH
To clarify, 25% volume of the dry and wet to one another? Measure one quart of the dry flake electrolyte to three quarts of water for a 25% mix? Do you use distilled water in both the mix and overflow?
@@RestoringReality The maximum usable concentration of KOH is normally considered to be 28%. That's 720ml Distilled Water and 280grams of KOH
Manual says 15%
The only problem I have with it is safety, HHO does not really exist, what we have is an explosive mixture of H2 and O2, you have a classic fuel and oxidizer mixed together, really the machine should separate both gasses and then remix them in the torch.
That would be a hydrogen fuel cell, and is somewhat more complicated.
This is a type of torch/generator that has been used for literally decades. It was literally the first gas mixture ever used for welding (and the gas produced by electrolysis exactly like this). I assure you, as long as you have a flashback arrestor (the bubbler), it is completely safe to operate assuming all other safety precautions are followed. Absolutely no reason to separate the gasses and remix them. It would just add unnecessary cost and complexity. However, unlike what furulevi stated, it really isn't THAT complicated. It is just a matter of separating the anode and cathode into two separate tanks connected by an electrolyte bridge. Oxygen is formed at the anode, hydrogen at the cathode, already separated with no further work needed. However, even that is simply unnecessary for an application such as this.
@@furulevi Erm no... You just put a tube around the negative terminal for one gas, and the positive for the other. That's secondary school level basic science. A hydrogen fuel cell works in a very different maner.
Thanks @@BJA717. Nice explanation.
Any chance you could open it up and show us what it looks like inside?
There is an other Video that Shows. Just search "whats inside a h160"
add potassium hydroxide to the water. should be 15amps
You must add much more KOH to the water
On a much larger home-made HHO generator a tiny amount of KOH significanty increased the current consumption... This must be current limited (I haven't looked inside it yet).
@@furulevi read instructions , they are saying 15%
@@davidp8157 Right, but I think 15% is too much, I used 2 teaspoon of 95% KOH and I am at 5 amp, that is about 10 grams or 1%.
@@motto666 You definitely need 150 gram. It should draw about 15 amps.
I have the same machine and you need to add natrium hydroxide to the water tank.
This is very important to give the water enough conductivity and the machine will produce more hydrogen gas .
I fill the flame arrester / bubbler with water but you can add a small amount off pure alcohol.
I believe in the paper that comes with the machine they say 1/3 alcohol then fill the rest with distilled water .
The machine will draw around 7 amperes if the solution of water and natrium hydroxide is good.
The machine works great and produces a really hot flame.
But i would like it to produce more.
If i had known i would have bought the 250 model because it has 2 hydrogen generator.
But you can do a lot of soldering with this machine 👍😀
I even do brass welding with flux on small parts and it works well 😀.
Just don't expect to much if you do bigger stuff .
Don't throw away your oxygen/ acetylene burner is my suggestion 😂
You made a mistake with the metal wire. It mustn't get so hot. If it gets too hot, all the carbon in the metal wire burns up. Excessive flame may only act briefly. Too long exposure to the flame will burn the steel. This is very tricky and not so easy to set the correct temperature. Remember HHO flames are much hotter than normal flames. And there are other physical properties. You can easely melt stones with HHO
Thanks!
Hi, i recently bought these machines. My bubbler did not come with a pre-assembled pipe as shown in 3.07, it came separate with an additional pin arrow and spring. i think it serves as a one way value to protect against flashback. im sure that you will also have these if you remove this pipe. i want to know which direction i should i connect this? Pin arrow pointing towards the pressure guage (upwards) or away (downwards)? My instinct says towards the pressure gauge (upwards) so it serves to shut of the air from hho generator tank if there is increased pressure in the bubbler from for example a flashback. However, i couldn't find anything in the instructions/manual. Any help appreciated. Thanks. Ash
The ratio is 1 part KOH and 3 parts water.
I think that is waaaay too much...
It's a 15 percent ratio
@@ghostlee900 i am stupid, please help? Are we measuring the weight of one to the volume of another? Would one quart of flakes and three quarts of water equal a 25% mix? Are you using distilled water in both the overflow and the primary tank?
this looks like the same thing being sold on eagle research for 2500 bucks minus the digital meters is it?
Copper gets very soft when annealed (heated) so you can easily break it even if welded. nice show though...
That is mostly for welding jewelry, very small stuff.
Secondo me,dopo più di un anno potresti anche farci vedere dentro cosa c è, secondo me faresti un bel po' di visualizzazioni. Fino ad adesso non l'ha fatto nessuno. Comunque grazie del video!
Good idea! ;)
Thanks very detail👍👍👍
You need the proper ratio of KOH Looks like you need a lot more and then in the bubbler tank use alcohol You’ll get a much better flame
Can you tell me why alcohol is preferred over water for the bubbler, please? Oh, and also what kind of alcohol is best?
Thank you!
I also have the same one, but the model is H160. I think your HHO flame is too small. My HHO flame is 10cm long. Check your NaOH: H2O is 1:5 and check if there is any air leakage.❤
This guy is driving me nuts
Neică, da ești român și ne vorbești în engleză ?
The instructions say I need to use NaOH not KOH. Is there a difference or will it work eitherway?
Mostly both are OK, KOH is somewhat better...
Just got mine today instructions say that having a grounding plug is absolutly nessisary to prevent electric shocks yours appears to be missing .
Devices work without any problem if grounding is not present, that' just a safety feature. The cable shown at 0:13 has 3 wires, phase, neutral and grounding. At 3:38 the wall socket had no grounding.
@@furulevi Oh, I see . Its different than US plug, US plug has a grounding rod that sticks out from the plug instead of a hole . I just watched a video with the same model as you and I that had ten times the flame and the person I bought from said to use 250 grams of sodium hydrochloride lye . Good luck.
@@personalitycat9842 *Sodium Hydroxide
hello furulevi but working at 0.1 pressure the flame is continuous and what temperature can come out I wait for you thanks
Is that maximum level of flame? Hardly visible, im so happy didn’t purchase this model, thank you
The flame is somewhat invisible, so it's longer then it seems!
CAN WE USE REGULAR SEA SALT. ITS HARD TO GET CAUSTIC SODA ( KOH) HERE
I'm not sure... That will generate chlorine gas also because salt is NaCl.
Maybe try using wood ash if lye/KOH s not available
Dude you should never touch the KOH with your bare hands . For real !
Imagine rubbing your eye after that! These are caustic chemicals, be careful!
You need more koh, but not too much, if you put too much then you will need to wash out. Can you open generator? I want to see quality inside of it, thanks.
I think I haven't used it since I made this video, I would also be curious about the inside also, and about the color of the liquid inside...
you need to add more KOH read your instructions its a ratio between the KOH and distilled water.
Could be...
Pour 1KG of distilled water with .2KG caustic soda powder, stir allow 20 mins to cool.
5 to 1 is the example, 35 ounces distilled water with 7.05 ounces of caustic powder.
You will create a very powerful mixture that will create a flame to burn through half the stuff your video showed couldn't.
You did not have the correct ratio in your drum of the machine.
If u put more KOH your Amps will decrease, so try to put KOH to reach 10 Amps minimum!
*increase
@@furulevi omg my bad, yes i mean increase the Amps!
Thx!
Can NaOH be used?
Cool machine. Does it have flashback arrestors?
The bubbler would be one, but as I noticed the flame does not reach the bubbler anyway even when the gas pressure is low.
@@furulevi thanks for the clarification
@@furulevi bubbler is flashback arrestor and works when used pproperly.Insufficient electrolyte, gave inadequate gas production and lack of results
Well I definitely won't be buying one of those. Thanks for the tip!
Just get a AC/DC TIG welder as you can weld pretty much anything with one of those (You can do most metals with just a DC TIG but you need AC for doing Aluminium (NOT aluuuuminium) and magnesium. Might be some others but I'm pretty there the main two). Especially if it's HF as it makes life a lot easier, even if you've got a lot of experience. Otherwise there will be a lot of tungsten sharpening n if it's thoriated it's even worse!
Try your best not to breath in tungsten dust as it's not good for you, like most exotic metals.
A larger machine of this kind would be better. This is sold as an acrylic polisher, not a metal welder.
clamping will aid with welding
This is painful, add more bicarbonate soda
Nice but the Flame has low Energie it is to smal flame You need a much mor bigger Flame to melt big thinks of metal
Yes the flame size of this model is small...
the flux capacitor is in backwards no amps should be 1.1 giga watts
DANKE .
This is extremely dangerous the way you designed this.. You need to seperate the gasses FIRST and store them that way, if you do not separate O2 and H you are going to end up with a flame that travels right back up the tubing and into the storage tank... hot potassium hydroxide everywhere not good! I've seen this. You can reduce the chances of it by creating a mesh based flame arrestor inline, but ideally separate the gas at production.
This was bought, not made at home. These devices don't separate the 2 gases, they don't have a separator membrane like fuel cells. The bubbler is the flame arrestor, a mesh type arrestor has no chance of stopping this gas.
@@furulevi Whether it was bought or made doesn't matter, this is dangerous. The bubbler doesn't protect anything, the gasses bubble up are O2 and H premixed, the flame can and sometimes does travel up the tube. They should be separated and its hard to believe these are sold this way!
Cam slābut merge , cāti litri face maxxim?
I want purchased this machine
We have used the ua-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
Have you tried using any other torch nozzles with it?
I think not... Will they make a difference, or I need a larger machine?
@@furulevi no add more potassium hydroxide
Does this machine have a flashback arrestor?
I think the metal cylinder (bubbler) acts as a flashback arrestor, but the tiny hole on the burner is also stopping the flame from going backward.
I have one of these and I have no idea what to do with it. Help?
Start doing carbon clean on cars
@@GlennDHS actually i just use it for tortillas now.
The flame is not as powerful as I thought. Are you sure your generator works well?
The flame is not too small, it is mostly invisible, at around 22:09 you can see that the paper is bending because of the heat of the flame, and at 22:12 it is even burning the paper.
Of course the flame is too small to melt the large metal shown at 9:34.
I am surprised how small flame your torch produced at 1,5 bar . I use my own torch and when pressure is anything around 0.1 bar flame is almost 10 cm . Just saying you are better off buying generator .
The flame is not too small, it is mostly invisible, at around 22:09 you can see that the paper is bending because of the heat of the flame, and at 22:12 it is even burning the paper.
The flame size depends on the nozzle diameter. You can simply drill it wider to get a bigger flame. Of course you will consume more gas than you produce, so ...
Stop breathing in noxious gases, jussayin
Great video
Apa distilată deci
Good
you probably need some flux to weld... maybe a little borax
In the case of aluminium the 2 pieces fused together without any flux.
@@furulevi yes aluminum does other metals need some help
Posta mais videos dessa máquina
Pre heat the metal with your propane torch first
frequincy ?
The low amperage I think is due to incorrect NAOH / KOH mixture. Distilled water will carry NO VOLTAGE> Also your unit has a pressure gauge where another I saw has a "pop-off" valve in it's place and describes the canister it sits on as a "Blow-back flame arrestor" Filling it with methanol would be not to smart I am thinking. ua-cam.com/video/rD8XyicU_bo/v-deo.html
Le prix de la machine svp en dirhams Pour Maroc ?????
can it be used for gold jewelery?
Probably yes... because gold should be in smaller quantities :) (I haven't tried it!)
Non riesco a portare in temperatura la fiamma.....
Where it has oxygen output?
Its already mixed
Possibility of using this machine for car engine interior cleaning?
It could work but a higher gas flow would be much better.
Glad I watched this as I was just about to buy one, but obviously they are just crap
Get a larger one.
The larger one is far more expensive. The issues I see is this is only half decent if you use the alcohol. The other thing is that you have no way to increase the output, of you could control the amperage then you could increase the hho has output
چطوری میشه یه دونه اینجوری تهیه کرد
The simplest way is to insert 2 metal (stainless steel) objects into the water close to each other and power it with direct current.
If I find myself needing to cut 1mm metal I will use tin snips not this over complicated cigarette lighter
Hey guys what does dude trying to teach you in an hour you can learn in 7 minutes on the next page
So basically this machine is useless for anything other than for tiny objects
I think so, I haven't really used it. Welding might be much better (TIG/MIG/MAG)
add more koh
Painful!!! Did you not read the instructions?
HOW MUCH
7 grams per liter
From ware we buy ?
www.ebay.com/sch/i.html?_from=R40&_nkw=H180+oxy-hydrogen+generator&_sacat=0&LH_TitleDesc=0&LH_TitleDesc=0&rt=nc&LH_BIN=1
Price
seems like a waste of money for something that is mickey mouse and does nothing ,try and let it generate more psi next time
This device is sold as an acrylic polisher, not as a welder for thick metals.
I see many mistakes your making.Do more homework before making the video such as mixing and adjust the electrolyte
Noooooo run 95 liter noo 000 liter
4:03 Apă distilată.
Romanian video 😂
Da ;)
I need
What a time waster. Hope he has all his fingers till now. No need to read instructions of a device when making a vid. He knows nothing about chemy, use of psa, brazing...
Mettre Guimps ça va encore
كم السعر
The cost $
This was around 170$ with shipping ► www.ebay.com/sch/i.html?_from=R40&_nkw=H180+generator&_sacat=0&rt=nc&LH_BIN=1
😂😂😂
if that is how it works its useless
Maître Gims
Maître
Read the instructions dude...
Which page more exactly? 0:35