thank you for taking time to make this video. very helpful . I don't know if I am going to attempt to do this myself , never done anything quite like this before. However it goes I will be watching this step by step . 😊
I think you got more views than you thought on this common issue! Ours is doing it quite a bit and was a recall replacement only a couple months ago. I’m going to get the impeller kit, I was just wondering if you’ve ever heard of just a bypass like putting a jumper wire in somewhere to do away with the sensor? Thanks!
I would check the filter first. If that's clean then check the pipe going through the tub to make sure that's not clogged as well. I hope you got it working and thanks for checking out the video!!
FYI: I replaced the impellor and put the gasket back on and tightened all the screws and it leaked. I took it apart again and put it together and it still leaked. There were little gaps between the screws. So what i did was open it up again and i put toilet paper in the middle of one of the pump sides and I sprayed Flex Seal on it. I sprayed a good thick coat. I let it dry like 5 minutes so it was sticky and not completely wet. Then i carefully wiped some off the inner edge so any excess wouldn't go inside the pump. I tighted the screws, wiped off the excess that came out the sides, and let it sit for about 20 minutes. (BIG TIP) Before putting it all together, you can put the hoses back on the pump and pour water in there while its upside down to see if it leaks. It didn't so I put it all back together, filled up the jacuzzi with water and voila! Works like a champ and not a single drop of water leaking!
Thanks for checking out the video and for the tip!! I have 2 spare pumps that have the E02 code and are leaking also, I'll try this if the leak doesn't stop.
thank you for taking time to make this video. very helpful . I don't know if I am going to attempt to do this myself , never done anything quite like this before. However it goes I will be watching this step by step . 😊
You are very welcome - I really hope you decided to try it!!
Thanks for the video - helped a ton with fixing my E02 error code.
Thank you for checking out our video - glad I could help!!
I think you got more views than you thought on this common issue! Ours is doing it quite a bit and was a recall replacement only a couple months ago. I’m going to get the impeller kit, I was just wondering if you’ve ever heard of just a bypass like putting a jumper wire in somewhere to do away with the sensor? Thanks!
Thanks for the video and link to the parts! It worked perfectly
Thank you for the feedback Tammy, glad you found the video helpful!!
My pump is working but my heater isn’t! Was it just your pump?
@monamarshall8769 yes just my pump wasn't working. The heater is separate from the pump. Thank you for watching!!
Thank you for the video. I followed the video but finally refilled the spa and I am still getting the E02 error. Do you have any other suggestions?
ua-cam.com/video/VK_3rkA9aew/v-deo.htmlsi=FhCUC6uDZTU4rbQ2
I would check the filter first. If that's clean then check the pipe going through the tub to make sure that's not clogged as well. I hope you got it working and thanks for checking out the video!!
FYI: I replaced the impellor and put the gasket back on and tightened all the screws and it leaked. I took it apart again and put it together and it still leaked. There were little gaps between the screws. So what i did was open it up again and i put toilet paper in the middle of one of the pump sides and I sprayed Flex Seal on it. I sprayed a good thick coat. I let it dry like 5 minutes so it was sticky and not completely wet. Then i carefully wiped some off the inner edge so any excess wouldn't go inside the pump. I tighted the screws, wiped off the excess that came out the sides, and let it sit for about 20 minutes. (BIG TIP) Before putting it all together, you can put the hoses back on the pump and pour water in there while its upside down to see if it leaks. It didn't so I put it all back together, filled up the jacuzzi with water and voila! Works like a champ and not a single drop of water leaking!
Thanks for checking out the video and for the tip!! I have 2 spare pumps that have the E02 code and are leaking also, I'll try this if the leak doesn't stop.
Does anyone else have an issue with the hottube tripping the breaker ?? Dang thing doesnt work
11:20 sit tight I'll be Rrrrrrrrrrrrrrr......lol
Well how did make out?? LOL Thanks for checking out the video.
@TheRetiredGuysGarage yes my friend your video was extremely helpful and got mine running again...cheers
Thank you. I got my working now
That's awesome and thanks for checking out the video!!
Thank you.
You are very welcome and thank you for stopping by the channel!!
It happened on ours after 3 days
Wow that's crazy!! Hopefully you were able to get it replaced under warranty. Thank you for checking out the video.