DRAG SLASH Build and First Run - No Prep RC Drag Racing Build
Вставка
- Опубліковано 6 гру 2019
- Plenty of trade secrets here so subscribe for more!
32 pitch 18/56
HW 6100kv set to 40degree timing
HW 120a Esc
Locked rear diff with JBweld
Proline Hoosier tires
JBconcept wheels
Proline tire glue
Traxxas wheelie bar
Traxxas SLASH LCG Chassis
Zeee 2s 100c 7.6v
PLEASE SUPPORT THE CHANNEL BY SUBSCRIBING
#hobbywing #proline #traxxas #zeee #jbweld #jbconcept #hotracing - Ігри
Nice looking build 👍🏁
Make sure your camber and toe is set in the neutral position
I knew you were gonna build one!
great bujild and who care if people think its a cheap ecu do what makes you happy im new to the rc scence and im going to find a way to turn my rustler into a no prep if i cant ima just buy the lcg chasis and start from groound up
Should they balloon that much on drag tires, how can you eliminate that
Lawwwddd nice
What tires ang rims is this sir?
You might have the wheely bar to low ? Or the chassis to low ? I think when you get going and the wheels balloon or expand it's taking it off the front wheels and the wheely bar is steering?
Possibly. Haven’t fixed it yet. But there are good feedback like yours. Appreciate it!
looks like your left rear tire might be ballooning faster than the right side making it push right. traxxas makes a solid slick tire that fits 12mm hexs. they come on the funny car.
It was actually the front right that was wrong. I screwed them on too tight not making it roll smooth
Pretty sure the funny car has 14mm hex's for the slicks
Weight in the front would probly help..Great Build..!!.👀💐☝👑🙏
You need to raise your wheelie bar that’s why it’s spinning out because the pressure is adding to wheelie bars
Wicked fast, but needs a gyro to help steer. I had the same issue, but with a Radiolink gyro, it’s a straight rocket. May not pass at a track, but can show the capability of the car.
I wish man. In no prep racing gyro is not allowed
No point putting a gyro on his going to have the difficulty as he is now once he ends up at a drag noprep having to take it off
I would start off on a better controller and tune in the speed bring it down
On speed little by little
Then look into his shocks set up
If that doesn't help He will need to change pinion then continue to test run
Decreasing speed till it goes straight not a huge decrease of speed but little by little will still go fast
Traction is the key to speed and going straight
It is trial and error testing and runs nobody gets it right straight away
Even the surface ground can effect it best place to test is where the noprep racing event is held
Then it's tuned for that surface
Not sure if you're still seeing comments on this since it's from December... but just curious... did you use the stock suspension arms and axles? Sick build!!
Yes sir I used all stock 👍🏼
What kind of motor you got in your RC I'm trying to figure out what motor to go with
The motor I went with for a while was the hobbywing 6100kv. It was good til people got fast lol
Try adjusting the shocks for a higher ride height. Maybe try locking the diff? Or thicker fluid?
I gave up this car. I have the DR10 now and I ranked 3rd in Vegas with it 👍🏼👍🏼
The right tire on this was screwed too tight and didn’t spin as well. And I locked the diff which shouldn’t be for what I learned
@@kgrc0078 so your not supposed to lock the dif? What should you do then?
Nice kit bro
UAE RC ADDICTS thank you! I love it!
What do you run in the diff? Thicker fluid?
Nope. I used JB weld to lock it. It works great.
You need sicker diff fluid in a differential
ok do you need to change nything on the regular slash to put drag tires on
This is a really old video.
You’ll need to use buggy arms off of the bandit and an LCG chassis.
Pretty much just buy a bandit and put a slash LCG chassis on it 👍🏼
@@kgrc0078 oh k
Hi bud I run the BL120 in 4 vehicles, one does 65mph at 2.2 seconds with a 4.5t and my others do around 55mph at 2.4-2.7 seconds with a 4.5 and 5.5t. You need to turn the punch down it’s at 7 as default and turn the timing up 1-2 levels to get the top end going.
Also the car will react totally different with a body your adding about another 160+ grams on the chassis don’t tune without the body on.
Appreciate the help!! 🍻🤙🏼
Dude thanks for the info have the same esc on a rustler with a 4400kv motor get about 55 the take off insane top end not so much
What gearing u run on the 4.5t I have the same esc and a 3.5t motor and what where ur settings on esc to get the 2.2?
@@fullsend1990 the 2.2 car is not an outlaw car it’s a vintage RC10DS which has ran a best of 1.87@70mph with the 3.5 Novak and BL120, the heavier Outlaw car ran 2.4’s-2.5’s with the BL120 and 3.5 Novak 87/22 gear timing max and punch dependent on surface.
@@jderbedrossian I just burnt one up today 3rd pass on the esc went 40ft and shut down. Now wpnt power up unplug it from the receiver and it powers on plug it in and won't turn. Not sure what's goin on
Did you had to tape inner slick tires before glueing ?
nope
@@kgrc0078 miy slick balloon like crazy
@@sammygonzalez7627 you’ll get better rollout that way. A 5” diameter tire will travel father than a 3” diameter tire at the same rpm. Hope this helps 👍🏼
I'd say your wheelie bar is the reason it's not wanting to go straight also try doing a burnout on a piece of carpet with some simple green, the simple green makes the tires sticky, and as far as the wheelie bar I'd go with the strc one or any other one that's longer and has more adjustment
I found out the reason. My front left tire was put on too tight and it wasn’t spinning right 🤦🏻♂️
Do you like that esc so far? I have a 60a and a 120a but haven't used them yet.
It’s pretty good 👍🏼
7:56 that evo tho
Damn you beat me to it
What motor did u use to have
I used the 6100kv hobbywing to begin with. It ran great till it got worn out. Then I switched to the trinity drag master hole shot 4.5t. That was awesome til it gave up too lol
Zeee are good batteries I have a couple
Where did you get
the drag tires
Amainhobbies.com
Thanks for responding so quick😁
I try to make my subscribers happy 🤙🏼 lol
Wheelie bar to low rear shocks to soft
What battery do u use
I love the gens ace redline 6000mah
NICE BUILD BRUH !! MY GUESS, IT'S THE TIRES !!
PKO RC yep that’s my guess
@@kgrc0078 Ride height too low. Heavier oil in rear shocks. More preload on right rear shock.
Nice ride!! You need to hold the camera steady. Too much motion.
will these fit those rims Pro-Line Racing 1/10 Reaction HP Belted S3 Rear 2.2"/3.0" Drag Racing Tire (2), PRO10170203
how come you didn’t go with a vxl motor?
VXL too slow for competitive drag racing
@@kgrc0078 aw dang, what would you recommend?
@@kgrc0078 and would you say keep my 2wd slash or try to get something else?
The 2wd slash platform is actually great. Just get an LCG chassis for it if you haven’t yet.
Most people who drag race nowadays use a 3.5t motor. R1 and maclan drk are the top brands currently. But you can also find others that are good too depending on your setup. Make sure your ESC can handle that speed too. 3.5-5.5 turn motors are competitive and they equal to about 6000-8000kv motors. They’ll burn most ESCs on 2s.
Goodluck!
@@kgrc0078 thank you very much!!
Dang hook a bruh up
Wheelie bar not good for prep racing and suspension looks to soft
0-60 time?
Sorry I don’t know
@@kgrc0078 thats ok. It seams like it would be quik tho!
yea ur wheelie bar is to low an also u want stiffer rear shock fluid cause the way ur is the car will just ride the wheelie cause the shocks aren't popping back up an also wheelie bar cant be to low as well cause that will also do the same thing
😊🤙🇦🇺🍻
Without a gyro and belted tires Idk if you have a chance hehehe. Sky Rc has a very affordable tiny gyro
If he needs A Gyro to drive in a straight line he should hang it up you should actually disable all that stuff because it turns the wheels in directions they don’t need to go
Maybe a body with good downforce
I know. It lacks aerodynamics. I’ll try again when the weather gets warmer
Get a new diff and put a heavy diff oil in it like 500k or 1 mil
try thicker shock oil 👌
In front, or rear, what do you recommend for front and rear on a slash like this build?
I'm running 60wt and might try going heavier to 65wt or more only because it feels like it's getting softer by the afternoon.
@@samangulo5681 both front and rear?
In front or rear for front and rear . . I need a drink
It's probably not tracking straight because of that tqi they've never track my car's right. I have much better luck with spectrum.
I had the right front tires on screwed in too tight. They weren’t turning smooth
What tqi and spectrum? What parts are those can you elaborate for a sort of noob
My bandit VXL will beat that drag stock
Unlock your diff
Un lock your diff