I very nearly threw this tank out before i realised it had a plastic spacer inside. Its a pain to get out because you have to pop the glass off by removing the bottom and applying upward pressure to the inner assembly but the straight glass doesnt give you anywhere to grip onto.
Ah I appreciate that, thank you very much! It's always frustrating that they limit us to 2ml but thankfully almost all of the tanks I've purchased have a removeable spacer to bring it back up to its intended capacity. I wish these were talked about more in vaping videos but I always gathered that they weren't really supposed to.
Best Guide. No magicians slight of hand on all the other too cool to school yt channels for my favourite vape for flavour. All I'll add is removing the black air pipe makes it easier to refill. But still more juice efficient than only contender Gen 80. So well worth the extra step.
@OxfordVapoursOnline thanx pls if you have a solution for another comment with 4 likes. How by Satan's beard do you remove that sticker on the inside of the glass that prevents it from filling more easily and at full capacity. And I'll answer that comment. Though the solution is probably "don't" as it's by design as google or the brand don't give an answer but lots of redditors think there is a solution but again that could mean anything.
I have the 8ml glass and recently its started coming off when you press fire, which not only burns my fingers, it also wastes an entire tank of juice. That's a lot of juice, even with a shortfill bottle. Ill have to go back to the shop tomorrow to have them look at it, but I think they are getting fed up with me lol. I have had a few issues getting used to this tank
Awesome I can easily remove coil w out a tool . Thanks for taking itank apart showing that reverse threading . My old Geekvape snap in was so difficult it took needle nose to remove and patience to line up install new coil - ugh .
Yes, it's there to conform to EU regulations. Remove it and you get 5ml instead of 2ml. It's funny how companies can still use this spacer method as a loophole xD
I recently bought this tank and I seem to be going through the coils in less than a week, averaging about 500 hits before it start to go off. I'm setting the wattage at the correct watts for the coil but it keeps going bad on me. I've seen people saying they get a month out of it, or about 4k hits. What the hell am I doing wrong?
@@OxfordVapoursOnline I soak each hole and inside the coil, leave for 5 mins and then put into the chamber and leave for another 10 minutes. I have the correct watt setting for the coil. I don't take long protracted or continuous hits. I just don't get how people say they get 4k hits before the coil needs changing. I've had it a month and have gone through 5 coils. It's frustrating because it is a great tank, other than that.
I found this difficult to fill, juice just didn,t want to go in. When i stripped it down i discovered a clear plastic sleeve inside the tank. This pops apart and when reassembled without this plastic menace, with a bubble glass, it made a massive difference. Come on Vaporesso, explain this "thing"
The plastic if for the the TPD regulations for EU. The limit for them is 2ML. Removing the plastic glass will give you the original 5ml capacity. However idk if we're talking about the same plastic
can you tell me what is the "second glass" behind the glass, which is just plastic? Where they show how to change the 8ml glass, they always take it out, but no one tells them what it is. Thanks🥰
It's a plastic spacer, it's there to conform to EU regulations. Remove it and you get 5ml instead of 2ml. It's funny how companies can still use this spacer method as a loophole xD
Thank you, Oxford VapoUr.One question: I know you said to wait 10 to 15 minutes to allow the coil to get moist, but is it OK to close the airflow adjuster, dry hit the vape, and soak the cotton that way?
I ordered two different bubble glass for this tank. When I tryed to install them I realised that it has an inner glass too and I can not take off the inner glass. And no youtube videos to help sort this thing out. The other thing is I tryed to put together the tank with the inner glass on plus one of the bubble tank, and the top wont go back to the normal position the logo not facing to the buttons side, it face to the left side. When I filled up this way it leaked too. Thats why I decided to not break of the inner glass. It seems like for me the original bubble tank totally different than the 2ml one. Soo you can not swap to fat glass just like that. Am I wrong? Or someone have a succes glass swap?
The inner glass should have a seam somewhere on it, that if you can just hook your nail into it it will split in too two separate pieces and can be removed easily.
@@ShiverPlumbingTN The first ansver helped me out. I didn't know that the glass can split to two part. But the itank was wery leaky somethimes. I use aspire odan tank now and it is amazing! No leak, easy coil swap even if the tank is full with liquid, long coil life, and huge tank capacity!
I very nearly threw this tank out before i realised it had a plastic spacer inside. Its a pain to get out because you have to pop the glass off by removing the bottom and applying upward pressure to the inner assembly but the straight glass doesnt give you anywhere to grip onto.
I searched for so many videos to try and figure out how to do it, couldn't find one till I found this comment, Thanks :)
legend
....... damn it, damn it. How do I get it out . 😅😅
So this is why my tank won't fill up completely? I knew I was doing something wrong
@@gmr9701what were u doing wrong
Thank you so much every other video skipped how to get the coil out
FYI - it has a clear removable insert, this is to conform with EU regulations, just pop the main outer glass down and you’ll see!
Ah I appreciate that, thank you very much! It's always frustrating that they limit us to 2ml but thankfully almost all of the tanks I've purchased have a removeable spacer to bring it back up to its intended capacity. I wish these were talked about more in vaping videos but I always gathered that they weren't really supposed to.
Best Guide. No magicians slight of hand on all the other too cool to school yt channels for my favourite vape for flavour.
All I'll add is removing the black air pipe makes it easier to refill. But still more juice efficient than only contender Gen 80. So well worth the extra step.
Very good tip, especially if you're using one of the wider 100ml bottles. Thanks for the comment!
@OxfordVapoursOnline thanx pls if you have a solution for another comment with 4 likes. How by Satan's beard do you remove that sticker on the inside of the glass that prevents it from filling more easily and at full capacity.
And I'll answer that comment. Though the solution is probably "don't" as it's by design as google or the brand don't give an answer but lots of redditors think there is a solution but again that could mean anything.
my filling part came apart! but seeing this explained it screwed backwards - saved!
How can I change or replace the glass?
I have the 8ml glass and recently its started coming off when you press fire, which not only burns my fingers, it also wastes an entire tank of juice. That's a lot of juice, even with a shortfill bottle. Ill have to go back to the shop tomorrow to have them look at it, but I think they are getting fed up with me lol. I have had a few issues getting used to this tank
Awesome I can easily remove coil w out a tool . Thanks for taking itank apart showing that reverse threading . My old Geekvape snap in was so difficult it took needle nose to remove and patience to line up install new coil - ugh .
How to replace spare glass
There is a plastic ring inside the glass. Is it removeable?
Yes, it's there to conform to EU regulations. Remove it and you get 5ml instead of 2ml. It's funny how companies can still use this spacer method as a loophole xD
I recently bought this tank and I seem to be going through the coils in less than a week, averaging about 500 hits before it start to go off. I'm setting the wattage at the correct watts for the coil but it keeps going bad on me. I've seen people saying they get a month out of it, or about 4k hits. What the hell am I doing wrong?
When the coil is new, are you making sure to prime the coils fully before using it?
@@OxfordVapoursOnline I soak each hole and inside the coil, leave for 5 mins and then put into the chamber and leave for another 10 minutes. I have the correct watt setting for the coil. I don't take long protracted or continuous hits. I just don't get how people say they get 4k hits before the coil needs changing. I've had it a month and have gone through 5 coils. It's frustrating because it is a great tank, other than that.
I found this difficult to fill, juice just didn,t want to go in. When i stripped it down i discovered a clear plastic sleeve inside the tank. This pops apart and when reassembled without this plastic menace, with a bubble glass, it made a massive difference. Come on Vaporesso, explain this "thing"
The plastic if for the the TPD regulations for EU. The limit for them is 2ML. Removing the plastic glass will give you the original 5ml capacity. However idk if we're talking about the same plastic
Cable tie !
How do you take the glass off as I wsnt to fit a bubble glass
Undo the bottom of the tank, then it will slide off the bottom of the tank
Well done - thanks so much!
bro holy shit , you're an actual godsend , i was gonna throw away this tank cuz i had to replace the gasket on the filling port , thank you so much
can you tell me what is the "second glass" behind the glass, which is just plastic? Where they show how to change the 8ml glass, they always take it out, but no one tells them what it is. Thanks🥰
It's a plastic spacer, it's there to conform to EU regulations. Remove it and you get 5ml instead of 2ml. It's funny how companies can still use this spacer method as a loophole xD
Thank you, Oxford VapoUr.One question: I know you said to wait 10 to 15 minutes to allow the coil to get moist, but is it OK to close the airflow adjuster, dry hit the vape, and soak the cotton that way?
You can absolutely do the primer puff technique also, I would still wait for 5 mins or so after doing that just to be sure.
@@OxfordVapoursOnline I primed by dabbing juice on the side holes only, then filled the tank. 10 mins later good to go.
I ordered two different bubble glass for this tank. When I tryed to install them I realised that it has an inner glass too and I can not take off the inner glass. And no youtube videos to help sort this thing out. The other thing is I tryed to put together the tank with the inner glass on plus one of the bubble tank, and the top wont go back to the normal position the logo not facing to the buttons side, it face to the left side. When I filled up this way it leaked too. Thats why I decided to not break of the inner glass. It seems like for me the original bubble tank totally different than the 2ml one. Soo you can not swap to fat glass just like that. Am I wrong? Or someone have a succes glass swap?
The inner glass should have a seam somewhere on it, that if you can just hook your nail into it it will split in too two separate pieces and can be removed easily.
Sounds like you need screw off cap close the fill door then screw cap back on
@@ShiverPlumbingTN The first ansver helped me out. I didn't know that the glass can split to two part. But the itank was wery leaky somethimes. I use aspire odan tank now and it is amazing! No leak, easy coil swap even if the tank is full with liquid, long coil life, and huge tank capacity!
Как установить время на дисплее?
Can i use GTX instead of this ?
only GTI
Is this restricted to 2ml capacity or does it have one of those removable rubber bung things inside of it?
Yes it is restricted to 2ml, as all tanks have to be under TPD, and the restrictor itself is glass, not rubber im afraid.
Yes it does see my comment!
@@OxfordVapoursOnline Restrictor is plastic not glass easy to remove glass use a rubber glove to grip the glass did mine in two minutes.
Poor design, have to remove tip to fill it lol
Dislike, I can’t take off glass
Worst tank
JUNK! Buy the SMOK.
it ain't junk buddy. You aren't understanding how to use it.