This is a quality flooring product that I'm interested in using for an RV. A few points about the installation from a 30-year commercial floor covering installer... Most of the installation techniques shown are fine or good enough, at least as far as the prep work of the substrate and the smoothing out of wrinkles/air bubbles. When you see the part about spreading the adhesive, take it as an example of what NOT to do. One must keep a consistent angle (approx 45*) with the trowel in relation to the floor so that a proper amount of glue is used to adhere the material. Think of the recommended notch size in the trowel as your metering device for using the right amount of glue. Watch closely and you will see many spots with almost no glue and other spots with a thicker layer. The result will be small air bubbles at the thicker spots and future points of failure at the bare spots. Aim for a consistent pattern of ridges over the entire floor. Also, as mentioned in a previous comment, try not to kneel or walk on freshly glued vinyl until the pressing/smoothing process is complete.
Charles Ferris amen brother on troweling adhesive, was thinking the same thing(51 years installing), also kneeling on vinyl flooring and fresh adhesive a don’t
It is best to remove the railing for a more complete installation. If you would like to make flooring mats that fit in general locations without removing railing and seating you can do that.
Yes - Aluminum surfaces must be sanded before adhering floor-covering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying this adhesive to remove oils or greases. For more information click this PDF: www.sailrite.com/PDF/390-Premium-Marine-Outdoor-Adhesive-Specifications.pdf
I have found that it's a better idea to stay off the vinyl after you lay it down or your knees/feet will push the glue unevenly and create unevenness. The cutting board works for what you can reach from the floor, and use a vinyl floor roller with a long handle to get the middle. Wish somebody told me this, I learned the hard way.
We have not had that issue when installing the vinyl flooring. However, your comments are greatly appreciated, because I could see that possibly happening of the glue were not very tacky.
Gerard143 - Can you please tell me which glue you used to install the Infinity Luxury Woven Vinyl? We have not discontinued any of the colors we stock (to my knowledge), so I was wondering if you purchased the flooring from Sailrite and if so what color?
AAT-390 Glue can be applied to aluminum flowing these guidelines: Aluminum surfaces must be sanded before adhering floorcovering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying the adhesive to remove oils or greases.
When cutting holes in the WV for cabling is a razor blade or what other tool correct to use? and is anything needed to keep the weave taught due to the holes
A razor blade can be used to cut holes or you can use a hole punch for cutting fabric assemblies to punch a hole in the LWV (the only issue with hole cutters for fabric is they are often not large enough). Scissors can also be used. If the hole is not too large nothing needs to be used to keep it taught.
my existing floor is the original vinyl, but very solid but have to cover a few holes where i took out the cabinets. is this a viable option for a pop up?
WHY cant this go into my rebuild of a classic 1969 apache ramada?....this seems better than the flooring i had picked out...still have to glue it no matter...and I like this better. Can it be glued to the existing floor if clean?
Infinity Luxury Woven Vinyl has a width of 102" you would need to measure the width of your pontoon to determine if it would work for you. www.sailrite.com/Brand/Infinity/Department/Fabric/type/Products?keywords=infinity
Jose Narvaez In the heat of the day with the sun’s heat backing the flooring I can still stand on it in my bare feet. Because it is a vinyl mesh woven flooring it allows some air flow, thus it keeps the heat down.
AAT-390 Glue can be used on Aluminum to bond Luxury Woven Vinyl Flooring. Note: Aluminum surfaces must be sanded before adhering floorcovering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying the adhesive to remove oils or greases.
I love watching your videos! They are detailed without being overdone.
I am so glad you like them. Let us know if you have any questions.
This is a quality flooring product that I'm interested in using for an RV. A few points about the installation from a 30-year commercial floor covering installer... Most of the installation techniques shown are fine or good enough, at least as far as the prep work of the substrate and the smoothing out of wrinkles/air bubbles. When you see the part about spreading the adhesive, take it as an example of what NOT to do. One must keep a consistent angle (approx 45*) with the trowel in relation to the floor so that a proper amount of glue is used to adhere the material. Think of the recommended notch size in the trowel as your metering device for using the right amount of glue. Watch closely and you will see many spots with almost no glue and other spots with a thicker layer. The result will be small air bubbles at the thicker spots and future points of failure at the bare spots. Aim for a consistent pattern of ridges over the entire floor. Also, as mentioned in a previous comment, try not to kneel or walk on freshly glued vinyl until the pressing/smoothing process is complete.
Great comments and suggestions. Thanks!!!!
Charles Ferris amen brother on troweling adhesive, was thinking the same thing(51 years installing), also kneeling on vinyl flooring and fresh adhesive a don’t
I like the color. Very nice finish. Does it feel rough on your feet if you are walking barefoot?
I have a Sun Tracker with aluminum floor. Cam you put it down without taking pontoon boat apart?
It is best to remove the railing for a more complete installation. If you would like to make flooring mats that fit in general locations without removing railing and seating you can do that.
Does that glue work on aluminum pontoon decks?
Yes - Aluminum surfaces must be sanded before adhering floor-covering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying this adhesive to remove oils or greases. For more information click this PDF: www.sailrite.com/PDF/390-Premium-Marine-Outdoor-Adhesive-Specifications.pdf
I have found that it's a better idea to stay off the vinyl after you lay it down or your knees/feet will push the glue unevenly and create unevenness. The cutting board works for what you can reach from the floor, and use a vinyl floor roller with a long handle to get the middle. Wish somebody told me this, I learned the hard way.
We have not had that issue when installing the vinyl flooring. However, your comments are greatly appreciated, because I could see that possibly happening of the glue were not very tacky.
Gerard143 - Can you please tell me which glue you used to install the Infinity Luxury Woven Vinyl? We have not discontinued any of the colors we stock (to my knowledge), so I was wondering if you purchased the flooring from Sailrite and if so what color?
Will your glue work if I Apply redguard moister barrier to the wood.
Is the vinyl flooring material flexible,enough to wrap around the edge of a 3/8” thick piece of plywood?
Yes, it will. I would glue it to the plywood top and then let it dry and then wrap around the edge of the board and staple to the bottom side.
I’ve purchased your floor covering and glue.
Installing marine grade wood flooring. Any gaps in wood sheeting? Or butt it up tight?
Is there any particular reason why you pronounce SAIL RIGHT as “SAY A RIGHT?” English is my first language, so just curious.
Could you roll this adhesive on an aluminum deck. I was also told it needs to applied to flooring
AAT-390 Glue can be applied to aluminum flowing these guidelines: Aluminum surfaces must be sanded before adhering floorcovering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying the adhesive to remove oils or greases.
How does it hold up to the sun and foot traffic?
It is excellent for UV resistance and also for durability for heavy foot traffic.
When cutting holes in the WV for cabling is a razor blade or what other tool correct to use? and is anything needed to keep the weave taught due to the holes
A razor blade can be used to cut holes or you can use a hole punch for cutting fabric assemblies to punch a hole in the LWV (the only issue with hole cutters for fabric is they are often not large enough). Scissors can also be used. If the hole is not too large nothing needs to be used to keep it taught.
Would this flooring be suitable for the interior of a recreational vehicle?
Absolutely, it would be great for both indoors and outdoor applications. Let me know if you have more questions.
my existing floor is the original vinyl, but very solid but have to cover a few holes where i took out the cabinets. is this a viable option for a pop up?
It would work very well in a pop up and can be glued to your current floor which is clean and level.
Thank You so much, I will be seeing you when I do. Love Your videos, Thanks alot!!
very nice
WHY cant this go into my rebuild of a classic 1969 apache ramada?....this seems better than the flooring i had picked out...still have to glue it no matter...and I like this better. Can it be glued to the existing floor if clean?
Yes, it would work great for that. It can be glued to your existing floor just like carpet would be.
This flooring can not be used on a 69 model.
WHAT SIZE IS THAT PONTOON BOAT IN THE VIDEO I HAVE A SUNTRACKER BASS BUGGY 18DLX WILL THAT FIT MINE ALSO
Infinity Luxury Woven Vinyl has a width of 102" you would need to measure the width of your pontoon to determine if it would work for you.
www.sailrite.com/Brand/Infinity/Department/Fabric/type/Products?keywords=infinity
obrigado muito bom
Você é bem vindo!
silk screen sqeegie would work very well
Yes, it would work great to smooth down the flooring. Thanks for the great suggestion!
How hot does it gets??
Jose Narvaez In the heat of the day with the sun’s heat backing the flooring I can still stand on it in my bare feet. Because it is a vinyl mesh woven flooring it allows some air flow, thus it keeps the heat down.
Sailrite ok thanks I’m thinking of doing this on my boo
Boat but I was wondering if it doesn’t get to hot
It does not get too hot, it only gets warm in the direct sunlight. I can still walk on it, without shoes, even if it has been in the direct sun.
I have a pontoon with All Aluminum deck, NO wood , like to replace carpet with vinyl?
AAT-390 Glue can be used on Aluminum to bond Luxury Woven Vinyl Flooring.
Note: Aluminum surfaces must be sanded before adhering floorcovering to remove aluminum oxide which will weaken the bond. Aluminum and steel surfaces must be cleaned with a mild solvent (naptha or mineral spirits) before applying the adhesive to remove oils or greases.
they should wear knee pads. Those knees must hurt!