한국분들 보세요. 여기에서 캘리퍼 볼트 21mm는 웬만한 렌치로는 안풀리고 아주 긴레버로 풀어야 됩니다. 그리고 저 타이로드 엔드볼을 저렇게 안빠집니다. 전용 리무버로 빼야 빠집니다. 망치로 때려도 안빠져요. 엔드볼 안빠지면 쇼바마운트위에 2인치 블럭 끼우면 끼워넣기가 되긴 하는데 드라이브 샤프트 조인트 부츠를 눌러넣다가 찢어먹을 수도 있기때문에 엔드볼을 빼고 작업해야 쉽습니다. 쇼바마운트는 영상에서 스프링 컴프레셔로 안누르고 그냥 쇼바 어셈블리를 통째로 180도 돌려서 장착하네요. 보통 쇼바는 원래방향으로 장착하는게 맞기때문에 마운트만 180도 돌리는게 맞는데 저리 장착하는것보니 문제없는 모양입니다. After watching your video and working on it as a reference, I lifted the 2020 Colorado by 2 inches front and 1 inch rear. thank you. In Korea.
And, when leveling 2.5 inches, it seems that only the mount has to rotate 180 degrees because of the position of the mount bolt. By the way, you rotated the entire shock absorber 180 degrees. Does it matter?
Yes, because the coil spring has to sit in a specific position within the inside of the top hat of the strut assembly. Only rotating the top hat/mount would cause drivability issues as the coil spring would not be allowed to seat correctly.
Most of our lift kits do not affect your factory warranty because there are no permanent modifications to your vehicle. Dealerships in certain regions have their own policies when it comes to vehicle modifications covered under factory warranty. We always recommend that you check with your local dealership about whether adding our kit will void your warranty.
I have a question, if you can helped me pliss If I lift my chevrolet colorado 2.5 inches, do I need to reinforce something? Or change the extended balls
If you are just trying to lift the front to level it out we have spacers for non-ZR2 Colorado's. supremesuspensions.com/collections/chevy-suspension-lifts/products/2015-2019-chevy-colorado-front-suspension-lift-kit-2wd-4wd?variant=21410659827792 Nothing for the rear right now though. The best way to find out what you would need to level it would be to get a measurement from center of the hub to the fender lip. Do that front and Rear and that'll give you the amount you'll need to level it out,. You should be able to fit a 33" tire, but a 32" would be a more confortable fit.
Adjusting your headlights would not be a bad idea if you find they are not in the optimal position to increase drivability when driving at night. However more times than not doing so is not necessary.
Technically it is type of suspension lift; If you're using a spacer to lift your vehicle via its factory suspension...well, its a suspension lift. Sure, its not a full blown suspension lift, which would be more of a full replacement set up and would set you back a few grand, but it is a suspension lift by all intents and purposes.
한국분들 보세요.
여기에서 캘리퍼 볼트 21mm는 웬만한 렌치로는 안풀리고 아주 긴레버로 풀어야 됩니다. 그리고 저 타이로드 엔드볼을 저렇게 안빠집니다. 전용 리무버로 빼야 빠집니다. 망치로 때려도 안빠져요. 엔드볼 안빠지면 쇼바마운트위에 2인치 블럭 끼우면 끼워넣기가 되긴 하는데 드라이브 샤프트 조인트 부츠를 눌러넣다가 찢어먹을 수도 있기때문에 엔드볼을 빼고 작업해야 쉽습니다. 쇼바마운트는 영상에서 스프링 컴프레셔로 안누르고 그냥 쇼바 어셈블리를 통째로 180도 돌려서 장착하네요. 보통 쇼바는 원래방향으로 장착하는게 맞기때문에 마운트만 180도 돌리는게 맞는데 저리 장착하는것보니 문제없는 모양입니다.
After watching your video and working on it as a reference, I lifted the 2020 Colorado by 2 inches front and 1 inch rear. thank you. In Korea.
You say the strut extenders are torqued to 43ft/lbs. I assume you use a crows foot as there is no room for a socket?
Just installed leveling kit. Great video my truck looks great now. Very helpful video. Thumbs up👍🍻
I like how the tie rod end just falls out nice and easy in the video. FML
I neither confirm or deny the existence of "movie magic".
I Have a 2008 gmc canyon have you guys done a video for that model?
We do not currently have a video on that application, sorry!
For 4wd do you just loosen axle nut or fully remove?
How do you torque something when a box wrench is used or a torque wrench won't fit?
You will want to use a torque wrench with a box end head/box end head adapter for a torque wrench.
And, when leveling 2.5 inches, it seems that only the mount has to rotate 180 degrees because of the position of the mount bolt. By the way, you rotated the entire shock absorber 180 degrees. Does it matter?
Yes, because the coil spring has to sit in a specific position within the inside of the top hat of the strut assembly. Only rotating the top hat/mount would cause drivability issues as the coil spring would not be allowed to seat correctly.
Do you have the video for 2006 colorado front lift leveling i need that one
We do - give us a call at 888-810-6791.
Yes, but are these modifications approved by GM ???
Most of our lift kits do not affect your factory warranty because there are no permanent modifications to your vehicle. Dealerships in certain regions have their own policies when it comes to vehicle modifications covered under factory warranty. We always recommend that you check with your local dealership about whether adding our kit will void your warranty.
I did the same procedure with my truck but I have never been able to align it. The tires on one side are worn out. What did I forget to do?
I have a question, if you can helped me pliss
If I lift my chevrolet colorado 2.5 inches, do I need to reinforce something? Or change the extended balls
No, other than an alignment, our kits are designed to be a direct bolt-on without any need for other parts or modifications.
@@SupremesuspensionsLiftKits Do we need a sway bar drop brackets with this kit?
wanting to do this myself butttt I don't know if I should. Might have to pay someone... lol
This will work for a canyon as well right? Also do you recommend a sway bar spacer?
hi, did you find out if it is the same procedure for a canyon? thanks
@@hcastilla2010 yes, i bought a sway bar spacer on ebay and installed it with the 2.5" spacer. Same process.
Any info on when it's going to be back in stock?
About another 2-3 weeks most likely!
I have a Chevrolet Colorado 2018 4 Cyl and 2 WD. Can I level it and put bigger tires ?
If you are just trying to lift the front to level it out we have spacers for non-ZR2 Colorado's.
supremesuspensions.com/collections/chevy-suspension-lifts/products/2015-2019-chevy-colorado-front-suspension-lift-kit-2wd-4wd?variant=21410659827792
Nothing for the rear right now though.
The best way to find out what you would need to level it would be to get a measurement from center of the hub to the fender lip.
Do that front and Rear and that'll give you the amount you'll need to level it out,.
You should be able to fit a 33" tire, but a 32" would be a more confortable fit.
Is sway bar spacer needed?
No, a sway bar extension/spacer should not be needed. The sway bar should be able to reconnect to the sway bar end links just fine.
yea think i'm gonna get a truck shop to do this for me... LOL
What happen to the rear lift kit?
This installation video is for the front leveling kit only. Unfortunately, we do not have an install video for the rear at this time.
Diff drop?
Not needed.
2.5" kit sold out. :(
We will have more of these soon. Check back towards the end of december!
Umm 5 minutes of my life taken away to watch install and 2 seconds of finished product
What about adjusting the headlights? Enjoy blinding everyone 😂
Adjusting your headlights would not be a bad idea if you find they are not in the optimal position to increase drivability when driving at night. However more times than not doing so is not necessary.
A front block is not a suspension lift.
Technically it is type of suspension lift; If you're using a spacer to lift your vehicle via its factory suspension...well, its a suspension lift.
Sure, its not a full blown suspension lift, which would be more of a full replacement set up and would set you back a few grand, but it is a suspension lift by all intents and purposes.