I greatly appreciate the real-life install videos. It shows the common issues you run into and how you overcame them which is honestly helpful for most of us DIY-ers out here! It's often frustrating to watch a "perfect install" video or a "let's just set this up on a table for a demo" video and it looks all super easy and then you go to do it and end up spending 3 days and 4 trips to Home Depot. Also, one question I couldn't readily find an answer to: What is the maximum distance for running the low volt wires from the Access Ultra (or the Access Hub) to the actual lock? Thanks again for all the great videos!
As I have stated in previous videos, yours are some of the best on UA-cam. My only comment on this product would be it would be perfect if there was a keypad on this too. I could see this being used at Air BnB's as well as most of the entry doors on my house.
Great video! Your Protect videos have helped me tremendously and these Access videos are giving me the confidence to try what has been a daunting and complex endeavor until now.
I'm a tech for a company specializing in building security. For this sort of thing we'd have used a Dremel tool instead of a jigsaw. A small handheld Dremel, while you have to be careful of it getting away from you, is far more precise. The oscillating saw was exactly what we'd have used. There are quite a few commercial electric strikes that can accept 12VDC to unlock, some that are fail safe (will unlock by removing power) or fail secure (which will stay locked when unpowered). Most of these strikes have spacers that can be placed in such a way as to position it correctly. Many also have a perimeter side cover which can be screwed to the strike so that the rough edge of the door frame would be covered (this allows for a some wiggle room in your cutting precision). I'm a bit surprised that Access ultra doesn't have a door position sensor (or door contact). Without that device, you'd have no way of automating any alerts to the door being propped open or forced open. How does Unifi handle motion rex detectors? In most door access systems, the motion rex not only releases a door but also acts to confirm entry. Thus with a badge reader and door contact (DC), the motion rex completes a tri-part entrance event: a badge is read, the DC confirms the door was opened, the REX confirms passage. Also, does Unifi have the ability to do monitored sensors? Many access control systems allow you to put resistors across your DCs and REX relays so that if the wires are cut and twisted together, the system would know it by the resistor no long being in the loop.
Hey Clay, you are my go-to for anything Ubiquiti. I can't find one but have you done a video on the Ubiquiti EV Station Pro? An in-depth video on setting up accounts and how to track usage would be helpful. Thanks!
Thanks for this useful video, I am wondering if this reader can be installed outdoors as it has IP55 (weather resistance) while the Intercom product clearly stated that is suitable for both indoor and outdoor installation with IP65. Weirdly when I filter their products with "outdoor" I get G2 Reader which has also IP55 but not the Access Ultra.
Fantastic video; What electric Striker you are using or prefer. It will be interesting to hear base on your expertise which strikers (brand) work best and why same with Cables and wires ...
@@EleanaOre I've used a bunch, this time I just used the UniFi one, it was fairly priced and worked.like a champ.. others were just high rated Amazon strikes or mag locks..
Have you done a panic exit door bar by any chance and do you know if anyone sell the surface mount electric strike for panic door? Thanks for the great video.
Can you install this without any other hubs or unifi gear required? Just plug it into a POE switch of any type? I would like to install this with a mag strike and exit button for a single exterior door
Can the lock output be used as a NC dry contact, or is it always powered? Not insurmountable, but we have several doors that are held locked by power from a separate system, it would be nice to easily add access to them by interrupting that power feed vs installing an extra strike, etc. Could be accomplished with a relay powered by the Unifi gear, but would be nice if it's really as simple as running a wire and splicing it in series.
So I'm a little confused now with the electric lock option. We have a metal frame glass door out front that doesn't have a latch (like the little thingy that you'd turn a door knob to unhook the door from the plate/frame to open it). It's just a handle and you pull or push to open the door, and it has a lock that latches when we close up for the day. We want to do an electric lock but not sure if that would work in our door situation. Would the electric lock make the lock itself turn to lock/unlock as we push the Exit button (or swipe to enter), if that makes sense..? Or would we have to use the magnetic lock option since there's no door latch thingy?
Just tried to install one of these today, we used the slim plate and for some reason, we cant get it to latch in place. even by hand with the bracket just resting on the back of it!
@@DPCTechnology I mean that I think it would be cleaner to mount the ultra on the wall without the plate. The plate is larger than the ultra and doesn't look as clean. I'm wondering if the plate is optional?
@@brandonreidy6989 if someone wants to rip it off the wall they could, but they could kick the door down too.. it alarms when tampered with and fails to locked..
@@DPCTechnology agreed. More curious if that was part of the design or not. A big difference between a curious person vs. Someone determined to break in. If someone can just grab it and rip the holding tabs off vs someone having the proper tools to remove it with intention. Also says something about the build quality as well.
I'm considering this on outdoor doors on a shop. Right now, I have keyed locks that I am sure a pickable by the right burglar. There are windows next to the door, so someone could break the glass and get in. Do you think this is appropriate in this application or am I downgrading security.
This is great and a fair price finally, but, one problem, anyone can now yank that out and put power to the strike plate with something like a battery and they’re in.. So, good for convenience, security, not so much.
@@DPCTechnology that would make a break in obvious, compared to no trace whatsoever. I do like it, and the simplicity and price though, have 4 in my cart now, soon as I manage to catch the Display Cast in stock. I use the notification thing from Crosstalk Solutions, but still can’t get it in time, they sell out quick.
I was thinking to use this for a house side gate, noting that it's IP rated, unlike the lite, and comes with a inbuilt hub unlike the g2 reader. Then a g2 reader pro for the front door, and a g2 reader for the back door to both run off the same hub. I'm trying to think of an elegant solution to not need 2 of these on the gate (one on each side)?
![Unifi Access Ultra [Review]: Quick Setup and Features](http://i.ytimg.com/vi/uyBFYsTNZCI/mqdefault.jpg)
![Unifi Access Ultra [Review]: Quick Setup and Features](/img/tr.png)
I greatly appreciate the real-life install videos. It shows the common issues you run into and how you overcame them which is honestly helpful for most of us DIY-ers out here! It's often frustrating to watch a "perfect install" video or a "let's just set this up on a table for a demo" video and it looks all super easy and then you go to do it and end up spending 3 days and 4 trips to Home Depot. Also, one question I couldn't readily find an answer to: What is the maximum distance for running the low volt wires from the Access Ultra (or the Access Hub) to the actual lock? Thanks again for all the great videos!
@@DominicRusso17 it's a good question, I don't know but will find out..
@@DPCTechnology I did ultimately find out the answer and it's approximately 500 ft
@DominicRusso17 That's good info to know. Thanks for sharing man
Great video! getting ours setup this weekend
@@MactelecomNetworks can wait to compare notes!!
As I have stated in previous videos, yours are some of the best on UA-cam. My only comment on this product would be it would be perfect if there was a keypad on this too. I could see this being used at Air BnB's as well as most of the entry doors on my house.
@@switz11 that would be cool!
Great video! Your Protect videos have helped me tremendously and these Access videos are giving me the confidence to try what has been a daunting and complex endeavor until now.
@@matthodgson5747 thanks for the kind feedback!!
Thanks for sharing, appreciate sharing the installation process
@@AlexGompper 👍👍👍
Great video. I always thought a hub was required.
Not for the new Ultra, it's a great fit for those lower security interior doors.. I love it...
I'm a tech for a company specializing in building security. For this sort of thing we'd have used a Dremel tool instead of a jigsaw. A small handheld Dremel, while you have to be careful of it getting away from you, is far more precise. The oscillating saw was exactly what we'd have used.
There are quite a few commercial electric strikes that can accept 12VDC to unlock, some that are fail safe (will unlock by removing power) or fail secure (which will stay locked when unpowered). Most of these strikes have spacers that can be placed in such a way as to position it correctly. Many also have a perimeter side cover which can be screwed to the strike so that the rough edge of the door frame would be covered (this allows for a some wiggle room in your cutting precision).
I'm a bit surprised that Access ultra doesn't have a door position sensor (or door contact). Without that device, you'd have no way of automating any alerts to the door being propped open or forced open.
How does Unifi handle motion rex detectors? In most door access systems, the motion rex not only releases a door but also acts to confirm entry. Thus with a badge reader and door contact (DC), the motion rex completes a tri-part entrance event: a badge is read, the DC confirms the door was opened, the REX confirms passage.
Also, does Unifi have the ability to do monitored sensors? Many access control systems allow you to put resistors across your DCs and REX relays so that if the wires are cut and twisted together, the system would know it by the resistor no long being in the loop.
Still waiting ...
Excellent points. Disappointing there isnt a response
Hey Clay, you are my go-to for anything Ubiquiti. I can't find one but have you done a video on the Ubiquiti EV Station Pro? An in-depth video on setting up accounts and how to track usage would be helpful. Thanks!
@@switz11 I'm installing pro and regular next week 😂😂. U must have esp
How about once your in the room do you have an exit button OR do you just open the door from the inside?
Yeah, you just use the door handle..
For the "2 wire cable" what wire are you using? 22 gauge or 18 gauge?
@@idjpashka 22
Thanks for this useful video, I am wondering if this reader can be installed outdoors as it has IP55 (weather resistance) while the Intercom product clearly stated that is suitable for both indoor and outdoor installation with IP65. Weirdly when I filter their products with "outdoor" I get G2 Reader which has also IP55 but not the Access Ultra.
Fantastic video; What electric Striker you are using or prefer. It will be interesting to hear base on your expertise which strikers (brand) work best and why same with Cables and wires ...
@@EleanaOre I've used a bunch, this time I just used the UniFi one, it was fairly priced and worked.like a champ.. others were just high rated Amazon strikes or mag locks..
@@DPCTechnology Thanks
Have you done a panic exit door bar by any chance and do you know if anyone sell the surface mount electric strike for panic door? Thanks for the great video.
@@GabrielGutierrez-sh5ti we use a push bar with a strike.
@@DPCTechnology could you share the brand and model please! Thanks
I use ubiquity strikes.. and then whatever push bar comes with the door. Typically we're not the ones installing the push bar or buying the door
Jeezus...
nice videos, are you open to ideas
Can you install this without any other hubs or unifi gear required? Just plug it into a POE switch of any type?
I would like to install this with a mag strike and exit button for a single exterior door
Yes, you just need a unifi device that can run access. The could be a cloud key, udm, etc..
@ thank you! And this will go right into a standard 1 gang box?
Can the door still be opened by a physical key, or does the electric lock keep it locked?
@@themannamedjames8766 The physical key still works.. so with the physical key you can open the door
Can the lock output be used as a NC dry contact, or is it always powered? Not insurmountable, but we have several doors that are held locked by power from a separate system, it would be nice to easily add access to them by interrupting that power feed vs installing an extra strike, etc. Could be accomplished with a relay powered by the Unifi gear, but would be nice if it's really as simple as running a wire and splicing it in series.
I want to get one of them for my house what happens if the power goes out
@@soesbetech it fails to locked.
@@DPCTechnology so if it locks and the power goes out what’s the alternative way to get in
So I'm a little confused now with the electric lock option. We have a metal frame glass door out front that doesn't have a latch (like the little thingy that you'd turn a door knob to unhook the door from the plate/frame to open it). It's just a handle and you pull or push to open the door, and it has a lock that latches when we close up for the day. We want to do an electric lock but not sure if that would work in our door situation. Would the electric lock make the lock itself turn to lock/unlock as we push the Exit button (or swipe to enter), if that makes sense..? Or would we have to use the magnetic lock option since there's no door latch thingy?
@@dw-dj1ii it needs an electric mag lock
Its unfortunate no dps input
Just tried to install one of these today, we used the slim plate and for some reason, we cant get it to latch in place. even by hand with the bracket just resting on the back of it!
Our fit without issue. Maybe throw up a picture on reddit or fb and Ill take a look..
Why was the large wall plate used?
@@NathanSweet it comes with the ultra..
@@DPCTechnology I mean that I think it would be cleaner to mount the ultra on the wall without the plate. The plate is larger than the ultra and doesn't look as clean. I'm wondering if the plate is optional?
@@NathanSweet you could go either way. It actually looks pretty good in the room.
Does the reader require security screws to remove it from the wall or does it just pop off with a tug?
@@brandonreidy6989 if someone wants to rip it off the wall they could, but they could kick the door down too.. it alarms when tampered with and fails to locked..
@@DPCTechnology agreed. More curious if that was part of the design or not. A big difference between a curious person vs. Someone determined to break in. If someone can just grab it and rip the holding tabs off vs someone having the proper tools to remove it with intention. Also says something about the build quality as well.
@@brandonreidy6989 agreed, like any security feature I think less info online is better than more.. I touched on it but don't want to over share..
I'm considering this on outdoor doors on a shop. Right now, I have keyed locks that I am sure a pickable by the right burglar. There are windows next to the door, so someone could break the glass and get in. Do you think this is appropriate in this application or am I downgrading security.
@@rpetty i would not use it for that application. Get the starter kit, its still cheap as far as access control is considered
What about request to exit?
It has an input for request to exit. Our door does not need it.
@@DPCTechnology How do you release the door lock from the inside then?
@@philhagger1668 the door handle opens/locks/unlocks from the inside.
This is great and a fair price finally, but, one problem, anyone can now yank that out and put power to the strike plate with something like a battery and they’re in.. So, good for convenience, security, not so much.
@@waynenocton it fails locked...
@@DPCTechnology I think you misunderstood me, you can pull it from the wall and apply 12 volts and the door will open.
@@waynenocton You can also kick in the door... I think a thief would do that first..
@@DPCTechnology that would make a break in obvious, compared to no trace whatsoever. I do like it, and the simplicity and price though, have 4 in my cart now, soon as I manage to catch the Display Cast in stock. I use the notification thing from Crosstalk Solutions, but still can’t get it in time, they sell out quick.
I was thinking to use this for a house side gate, noting that it's IP rated, unlike the lite, and comes with a inbuilt hub unlike the g2 reader.
Then a g2 reader pro for the front door, and a g2 reader for the back door to both run off the same hub.
I'm trying to think of an elegant solution to not need 2 of these on the gate (one on each side)?
@@will67755 don't think this is the solution..
You'd recommend using 1x g2 reader (preferable, or 2 if i need to) and 1x extra hub?
@@will67755 I think u can get away with one
I would respect this video a lot more if he was using anything but Ryobi tools.
You nailed it! The whole team was making fun of Sean when he was filming...