T06 Diana trigger adjustment
Вставка
- Опубліковано 3 гру 2024
- Brief how too with me adjusting a Diana T06 trigger. Its a juggle between 2 screws so bear with me as i get the trigger pretty sweet eventually and show how to push the tip point back around 10mm or so.
Warning for Diana 34 EMS! Do not attempt to bend tab to adjust first stage travel as suggested. Casing is cast steel, will not bend, and will snap right off. I now have a broken trigger on a rifle very dear to me, because of attempting this.
Thanks for the tutorial. I did what you did, and it turned out great. I j pulled the assembly out of the stock and was able to cock it, and shoot it while adjusting the screws. This trigger is now on par with my HW 30 Rekord trigger. Thank you again for a clear how to vid.
Diana should give you that job bro 👍🏻
What a great video, brilliant! just got a 56 TH, with hardly any use, this is invaluable!
subscribed immediately!
Remember on a 56 the trigger comes back, do not bend the tab, leave the blade at full forward position.
@@TonyLeach-airguntech Thanks Tony!
That was very helpful. Can you explain how to place my new to me RWS Diana 34 Classic with T06 trigger back to safety once I take safety off?
Let’s say I was ready to shoot but changed my mind. Thanks!
Good to see how to adjust the t06 trigger
Tony, Thanks for taking the time to show and discuss the whole process. It is very clear that the two screws in the trigger blade work together even though they control separate parts of the system.
I know this is an old video, but I have a quick question: You said to adjust third screw behind the trigger blade all the way OUT. Is that correct? I have it adjusted all the way in. After following your instructions I have a trigger weight of 1lb even. That was measured in the gun several times and it is always 1lb.
The first stage is very long, but with a crisp, short 2nd stage with 1lb break I didn't want the first stage too short.
What will happen if I back that third screw out? I dont' want to mess up the way the trigger feels now. Also that 3rd screw is very fragile looking. I'd rather not play with it too much.
How to make softer trigger of t06 harder ?
Hi friend I adjusted my bristle trigger on my 440th and now the safety lever engages but no longer works, do I need to file the safety stop rod as the trigger is additionally angled??
Have you change the Trigger cap Screws with grub screws? Can you please Tell me the length and width from screws.
Can we remove the safety knob. Will the trigger function without the safety. I broke the safety knob so want to do away with the safety.
Awesome video sir...adjusted my trigger with your help.....wanted to ask something, the tab that stops the trigger from going forward, it broke in my gun, even though I hadn't bent it like u suggested....any opinions on how to repair it?
Can you please please do a video of a trigger re build as I accidentally took mine apart and now I don't know where everything goes as in the springs etc. This would be a life saver
Tony can i test the trigger unit by inserting a round bar or similar into the opening for the piston rod. My rifle trigger operates as your video but fails to cock when in the receiver and the lever operated [ K98].
just use the piston, with the spring guide and no spring push the piston into the trigger body keeping is square and it should push the sear back and engage.
Lol it was a real pain getting that grub screw back into compression tube for the cocking link . I fitted a Tbt drop in kit and made sure the guide was the right length. Even cut it short to make sure. Re-assembled but wont lock after cocking. Just glad the trigger is working.
Not going to keep asking questions ...but... is the T06 ok to strip down ? Only trigger i have stripped is the TX 200 CD.
colin biggs never full steipped one...does not look overly hard to do though.
do you know were i can buy a t06 trigger ¿
Скажите пожалуйста надо чем-то смазывать этот усм и чем ?
Adjusting triggers usually is ;-)
well just adjust it forward a little....i was showing how you can adjust it, not where to adjust it too ;)
I fabricated a shim between the tab and the trigger blade. The tab appears to be cast aluminum and can easily break. Anyway you are correct without moving the trigger blade back any other trigger adjustments are futile.
You can drill and tap the tab and push the blade back with a grubscrew...I just showed the 1way lazy way I do it.
Tony Leach
Understood-I was getting really frustrated adjusting the modified T06 on my new 340 n-tec until I found your video. You saved me hours of grief - thank you for a great instructional video.
drill thru and use a pin like the CD unit does on a TX
photos.app.goo.gl/xPzZv1pW5zujtUJm7
بسیار عالی
کاش یه نفر فیلم میگرفت فاصله نزدیکتر
If it aint broke…
What a terrible excuse for a trigger. Diana made such a fine rifle, and then went and put a trigger on it that is difficult to adjust, and keeps changing every time the rifle is shot. A stick and a piece of string would be better.
its actually a nice trigger once set up right, easy as good as CD or Rekord
@@TonyLeach-airguntech heads up. You cannot bend the tab to adjust first stage travel on the new Diana 34 EMS. The tab is too thick, will cause the casing to fracture, and the tab to snap right off. This is what happened to me, and admittedly I am really upset about it. The only springer I own, and there are sentimental attachments to the gun. I don't know how I am going to fix it, can't afford a new trigger unit, but I will figure something out. Please inform viewers.
@@Williamthebrand drill the tab and use a course thread 3mm diameter grub screw to make an adjuster instead. Lock in place using blue thread lock