This is the best mid rise lift. This lift is sold under many names but it’s awesome. I got rid of the Quickjack and bought this style of lift. And most importantly, it makes you feel safe.
@@snazy7777 depends on how long you consider “survive”. I’m pretty sure it would start rusting on the joints and the control panel would surely have to be under some cover. Long term i don’t think any of these are built for outside
This was a very informative video. Thank you! I have the autokato/katool x85 (usa model) which looks nearly identical. It doesn't have grub pins and has plastic sliders under the back bar.
Thanks for sharing. Perfect timing as I am looking for a scissor lift myself here in North America. Most of the brands here are indeed Chinese sourced too (so I believe TwinBush as well). Ingenious design of the mods. Love it. For my use I would prefer to dolly the lift freely on your "side swipe wheels". I guess it should be possible to introduce a shaft and spindle on them, to enable them to rotate 360 degrees. Cheers.
Great video there! Exactly what I was looking for, I am on the process of getting one that I should hopefully confirm in the next few weeks. Just out of curiousity, if you don't mind, how high from level ground at the floor to the roof measured?
@@Drftn32 you mean my garage height? I think I have around 260cm. The lift goes up about 100cm. When I fully raise the M5, there’s not much space left, because I have the garage door rail in the way as well. So basically, any higher would not be possible for me anyway
@@AlfisGarage Yes garage height, sorry for the confusion. Thats awesome! Least i feel a bit better as the height in my garage is about the same. Now its just a mission to find one here, its like triple the price here in NZ
Do not tighten the grub screws fully. These are designed to be tightened and the backed off to act as guide in slot on the rod. This allows rod to have some free play and allows the jack to operate faster.
That is interesting - i understand what you mean and you could be right, but then I think the grub screw should have a flat bottom and also there should be some loctite, so that grub screw doesn’t back out
If the grub screw isn't tight it will probably fall out unless you loctitie it in. It doesn't really matter either way. It is a cheap Chinese design with no inner bearing bushes. If the grub screw is tight, it just means the pin is stationary in relation to the two outer holes and rotates in the centre hole. All the wear will be in the centre of the pin or the centre hole. If it is loose, the pin will be allowed to rotate in all three holes, sharing the wear. These are really only designed for domestic use with low cycles compared to a shop lift. You will wear out before the pins or holes will, which is why they don't bother to install grease fittings. As the pins are a sliding fit to the holes, most of the grease was pushed out when you refitted the pins.
This is the best mid rise lift. This lift is sold under many names but it’s awesome. I got rid of the Quickjack and bought this style of lift. And most importantly, it makes you feel safe.
Thanks for watching. I never had the Quickjack and I think it is practical how portable it is, but this seems definitely stronger. 👍
Skate board wheel dollies for the win! Thank you!
Greetings from Poland, kupczyk is polish brand💪
Do you think this brand of lift would survive outside/outdoors exposed to the elements?
(Damp British weather)
@@snazy7777 depends on how long you consider “survive”. I’m pretty sure it would start rusting on the joints and the control panel would surely have to be under some cover.
Long term i don’t think any of these are built for outside
This was a very informative video. Thank you!
I have the autokato/katool x85 (usa model) which looks nearly identical. It doesn't have grub pins and has plastic sliders under the back bar.
@@terrencethorsen thanks for watching :)
Very Good Sir. From Ohio US
@@patriotu.s.elections7879 Thanks for watching! :)
Thanks for sharing. Perfect timing as I am looking for a scissor lift myself here in North America. Most of the brands here are indeed Chinese sourced too (so I believe TwinBush as well). Ingenious design of the mods. Love it. For my use I would prefer to dolly the lift freely on your "side swipe wheels". I guess it should be possible to introduce a shaft and spindle on them, to enable them to rotate 360 degrees. Cheers.
Thanks for watching!
Yes you could surely design it with caster wheels that will rotate 360 degrees :)
Great video there! Exactly what I was looking for, I am on the process of getting one that I should hopefully confirm in the next few weeks. Just out of curiousity, if you don't mind, how high from level ground at the floor to the roof measured?
@@Drftn32 you mean my garage height? I think I have around 260cm. The lift goes up about 100cm.
When I fully raise the M5, there’s not much space left, because I have the garage door rail in the way as well.
So basically, any higher would not be possible for me anyway
@@AlfisGarage Yes garage height, sorry for the confusion. Thats awesome! Least i feel a bit better as the height in my garage is about the same. Now its just a mission to find one here, its like triple the price here in NZ
@@Drftn32 good luck mate!
Fantastic video! You are quite inventive.
@@marktbeauchamp thanks for watching! :)
Hey man, these are great tips!! Thank you very much for sharing!
Great review, excellent tips. That lifting fitting is perfect, why couldn't they do that?? 🙂
@@KJs581 exactly! It should have come like this :)
Can you take it apart to put it in the back of a minivan for transport?
No, that's unfortunately not possible.
Hi
Do not tighten the grub screws fully. These are designed to be tightened and the backed off to act as guide in slot on the rod. This allows rod to have some free play and allows the jack to operate faster.
That is interesting - i understand what you mean and you could be right, but then I think the grub screw should have a flat bottom and also there should be some loctite, so that grub screw doesn’t back out
If the grub screw isn't tight it will probably fall out unless you loctitie it in. It doesn't really matter either way. It is a cheap Chinese design with no inner bearing bushes. If the grub screw is tight, it just means the pin is stationary in relation to the two outer holes and rotates in the centre hole. All the wear will be in the centre of the pin or the centre hole. If it is loose, the pin will be allowed to rotate in all three holes, sharing the wear. These are really only designed for domestic use with low cycles compared to a shop lift. You will wear out before the pins or holes will, which is why they don't bother to install grease fittings. As the pins are a sliding fit to the holes, most of the grease was pushed out when you refitted the pins.
@@ricbarker4829 yeah, you’re probably right
Do you have the 3d printed files you can share by any chance for the side to side wheels?
Sure! I just uploaded it to Thingiverse and added the link to the description. Good luck building!
@@AlfisGarage thanks I really appreciate it.
loud musig: I adjust the volume, than I can't hear you. I am not interested on the music at all!
Thanks for feedback!