Quick tip. When installing plugs in a deep or blind spark plug hole use a piece of fuel line over the plug. You can twist that to install the plug. It makes it easier and prevents any possibility of cross threading. Ride safe.
Nice video! I would just recommend to use an air compressor to clean out any debris that may have found its way down in the spark plug recesses. It will be a very bad day if something falls into the combustion chamber when you pull your plugs.
Nah. Well, it depends. A tiny bit of dirt is just gonna get blown out the exhaust. If a pebble falls down in there or something that's a different story
Hello! I watch your video here in Brazil! The step by step will definitely help me a lot. This way I won't have to pay for the service! Thank you very much!!
Good video. Only thing I would recommend adding is blowing out the areas around each plug well before removing the plugs to keep debris there from entering the cylinders.
Thank you for sharing video. I'm going to try to tackle my 2020 tri glide. Great video you should be a instructor- Master mechanic well said and easy instructions to follow.
from jack... your video helped , thanks. i will add this...on the inboard side of mine , i found a small pebble that would NOT come out with an air hose(had to use a long tweezer to pull it out... my advise is to eyeball the recess before removing plug.
Just a little helpful trick - before taking off the tank cut the overflow hose and then when reinstalling the tank just use a plastic connector (you can find at any hardware store) to connect the two pieces of hose. That way you don't have to reroute the hose every time you have the tank off.
Great video overall. It helped me in general. DO NOT Install the spark plugs with anti-seize. They are more likely to come loose if you put it on. Additionally, the torque spec changes with the use of anti-seize and so does the resistivity (ability to electrically conduct with ground.) Also, you probably got that crap in the combustion chamber which will get on the catalytic converter. Little dab goes a long ways. I use this stuff on tierod ends for cars. YOU DON'T need a whole lot. That is why it comes in such small tubes. Overall great video. Appreciate your contribution. I would put a disclaimer on the video though.
Thanks for the tips Frank and appreciate you watching. I do have a disclaimer in the description of the video which I do on most "how I do it" videos. Thanks again man!
Also should never use a click-type torque wrench on aluminum. I cracked a Jeep Overland's head at just 18 #/ft and learned this the hard way. Had just ported them too. Anyway, best to use a dial-type or digital torque wrench on aluminum to avoid the extra impact from that damn click.
I always enjoy all your videos. However I don’t know a thing about motorcycles 😂.. I’m always looking forward for your next RV updates! You are so knowledgeable and your projects are very clean and organized. I know this is off topic but I would love for you and your wife to give a tour of your home and your garage as well. Thanks for sharing! Stay safe well and happy!
That’s one crazy design flaw in my book.I change the plugs on my 04 Soft tail in 10 minutes. No removing anything but the plug wires . But you did a great job and a nice how to video
Taking the fuel tank off is easy peasy and so much easier than it used to be. Take it off.. clean everything up . 5 minutes.. you'll get so good at if you do it often is automatic..
I want to see the unedited version taking off the plug wires! Seriously, do you use dielectric grease on the wire? I find it easier to get the boot off. Great video as usual!
Thanks Ed, the plugs are 2 years old so they actually came off as easily as the video shows. I haven't used any grease on the wires. Have you experienced trouble getting the wires off?
@@TollesonLife I use it for: 1) water repellent, 2) ease of getting boot off, 3) fighting corrosion. There have been occasions where the boot was really tight.
I find the harley brand works well. I use it on every electrical connection. There is also ACF50 of your from the aircraft mx world but the harley stuff works well.
I didn’t know the 107 had 4 plugs in them my wife has 2017 trike with the 107 . I really miss your riding videos hope to see some this summer. Take care stay safe .😬👍
Tech tip use a piece of 3/8 fuel or coolant hose to remove the plugs simply crack and loosen with the ratchet and turn them approximately a half turn and stab the spark plug with the hose and twist it out the plug will stay in the hose when reinstalling simply put the plug into the hole with the hose rotate counter-clockwise until you feel a click then rotate the hose in until it stopped turning then tighten to spec. I Change a lot of spark plugs in the equipment that I work on. Also I would submit that you used too much antlseize jmho awesome and very informative video by the way. One additional thought since there is a torque value range and you put anti seize on the threads that technically means the threads are wet and a lower value in that range should be used again jmho
I followed along and the job done.. not bad at all. One interesting fact I found with the original plugs, they were not even close to being within spec... from the factory no less!?
Light dab of anti seize on plug threads, torque to lower end of spec torque value to prevent over tightening. Light amount of dielectric grease to inside plug wire boots to help with removal next time, boots sometimes stick to the porcelain. Before removing plugs, blow area clean with shop air . Very small dab of anti seize on bolt threads at reassembly. Prior to photos, notes - YES. Be sure plugs are ion sensing on newer models, too.
Thanks for the video, I haven't changed the plugs yet on my 2017 RGS, but the mileage is saying it's time. You don't use dielectric grease on the plug wire boots? Just curious.......
Thanks Scott! I had 2 long rides canceled due to Covid 19. One was to New Mexico and the other to Iowa. Next ride is late in July to Illinois, around 800-900 miles and the Key West, Fl in September.
Tolleson Life thanks for the reply! Yes, Covid 19 has certainly thrown a spanner in the works for all our plans, hopefully you get back out on the road in July. I really enjoy watching the videos of your trips with your brother and your mates. Be well and stay safe!
I was reading every two years it is recommended to change out the plugs. Ive had bikes my whole life, this seems way too quick. I can see if I had 20k+ miles, but I only have 7100 thoughts?
Hey Kickin Asphalt. The Harley book for my model says every 30,000 miles. I just do them a little sooner. I think you are rolling fine with 7100 miles.
@@TollesonLife Thanks, I took my 20185Harley Road Glide in for the 10k service, they checked the plugs and said they were fine. the book i saw said 30k or 2 years. I guess my plugs must be OK since they had the chance to change them and charge me but they did not!
Nice presentation, but it certainly changes my mind about buying a new bike. My opinion, it's ridiculous to have to pull a tank just to change the plugs.old school for me...thanks.
You were lucky to get them off. One of my Screamin eagle wires tore right out of the boot. Luckily I had the original stock set lying around til H-D was able to get them. I even had a boot removal tool and took off the seat. I've since learned from a master tech that the MocCo has a special tool they send to the dealerships just for that. Was told by another stealership it was available to the public. Lying fuckers...it's made by Lisle, part #51750. $22 at Home Depot. Specifically made for the M8. Since then I use the spark plug boot/dielectric grease. No issues.
Quick question.. if I’m just replacing the cables (aesthetic purposes) there is no need to remove the tank.. correct? (2019 Breakout 114). The instructions seem like overkill for just changing cables..
Hey Altomar Home, I'm not really sure about the Breakout. It shouldn't be that difficult to change out the cables but again, I'm not sure about your bike and how they are ran. Best of luck!
I have a problem with my 2015 roadglide, when I turn the knob to on position takes me to enter pin right away even with fob present, and no headlight, no fuel pump priming , no infotainment, nothing any idea what can it be? Battery?
Quick tip. When installing plugs in a deep or blind spark plug hole use a piece of fuel line over the plug. You can twist that to install the plug. It makes it easier and prevents any possibility of cross threading. Ride safe.
Great tip!
Why would that help?
One of the best "How to" videos I've ever seen, I'll be changing my plugs in the next week or so and this is very helpful. Thanks !
Thanks SPS!
I really appreciate the way you explain your videos. Clear and precise !! Thank you !!
You're very welcome Ben!
Great camera work, clean cut video with just enough information to get the job done properly. No fluff, love it.
Much appreciated Famster!
Nice video! I would just recommend to use an air compressor to clean out any debris that may have found its way down in the spark plug recesses. It will be a very bad day if something falls
into the combustion chamber when you pull your plugs.
Great point Matthew, I had just washed and blew this off but failed to mentioned that in the video! Thanks for sharing.
My thoughts exactly
Nah. Well, it depends. A tiny bit of dirt is just gonna get blown out the exhaust. If a pebble falls down in there or something that's a different story
Hello! I watch your video here in Brazil! The step by step will definitely help me a lot. This way I won't have to pay for the service! Thank you very much!!
Thanks for posting it does make you wonder about modern technology used to be so simple
Thanks for your help my friend. Using this video, my spark plug replacement went as smooth as I could have expected
Glad it helped my friend!!
Excellent and thorough presentation.
Good video. Only thing I would recommend adding is blowing out the areas around each plug well before removing the plugs to keep debris there from entering the cylinders.
and DONT USE ANTI-SEIZE!
Great video thanks for sharing
great video, to the point and easy to follow
Thank you for sharing video. I'm going to try to tackle my 2020 tri glide. Great video you should be a instructor- Master mechanic well said and easy instructions to follow.
Glad it was helpful and best of luck!🙌🙌
quick simple and to the point on what to do the steps to do it in etc. very nice video much appreciated on the how to
Glad you liked it!
Very detailed video. Thanks for posting these great informational videos!
Sure thing D. Mar!
from jack... your video helped , thanks. i will add this...on the inboard side of mine , i found a small pebble that would NOT come out with an air hose(had to use a long tweezer to pull it out... my advise is to eyeball the recess before removing plug.
Thanks for sharing🙌
Daryl, I have never seen your hands dirty before. Great video, keep up the hard work.
Lol Rodney! Appreciate ya man!
Great video - thanks for sharing this. I haven't yet changed the plugs on my M8 Softail Street Bob, but this will be a great reference.
Thanks Ron's Workshop, glad the video might be helpful to ya.
that's very good work !! Brother, thank you from sardinia (italy)
Thanks a lot!
Just a little helpful trick - before taking off the tank cut the overflow hose and then when reinstalling the tank just use a plastic connector (you can find at any hardware store) to connect the two pieces of hose. That way you don't have to reroute the hose every time you have the tank off.
Interesting, I never thought of that. Good idea.
Thanks for the tip Jim!!
Thank you so much I followed step by step and it was great !
Great! Glad I could help Oscar!
I have my tank off already, so I’m gonna change the plugs while I’m at it! Thanks!
Good plan!!
Great video overall. It helped me in general. DO NOT Install the spark plugs with anti-seize. They are more likely to come loose if you put it on. Additionally, the torque spec changes with the use of anti-seize and so does the resistivity (ability to electrically conduct with ground.) Also, you probably got that crap in the combustion chamber which will get on the catalytic converter. Little dab goes a long ways. I use this stuff on tierod ends for cars. YOU DON'T need a whole lot. That is why it comes in such small tubes. Overall great video. Appreciate your contribution. I would put a disclaimer on the video though.
Thanks for the tips Frank and appreciate you watching. I do have a disclaimer in the description of the video which I do on most "how I do it" videos. Thanks again man!
Good god that was a lot of anti seize! Legit made me gasp hahaha
Yo I said the same thing 🤣🤣🤣🤣
Also should never use a click-type torque wrench on aluminum. I cracked a Jeep Overland's head at just 18 #/ft and learned this the hard way. Had just ported them too. Anyway, best to use a dial-type or digital torque wrench on aluminum to avoid the extra impact from that damn click.
oh wow that's alot of antiseize. I've never done antiseize and torque wrench. one or the other especially with aluminum heads
Should have used copper anti-seize instead
I always enjoy all your videos. However I don’t know a thing about motorcycles 😂.. I’m always looking forward for your next RV updates! You are so knowledgeable and your projects are very clean and organized. I know this is off topic but I would love for you and your wife to give a tour of your home and your garage as well. Thanks for sharing! Stay safe well and happy!
I appreciate that Latada! Our house is a simple, modest home and wouldn't be that interesting of a video...LOL!
Excellent vid man. This looks super simple if your good with your hands
Great video. I did it start to finish in about a half hour. 👍👍👍👍👍
Awesome Ed. About time for me to do this again.
You and your wife are a BEAUTIFUL couple! God bless you!
Thank you so much Ted!
That’s one crazy design flaw in my book.I change the plugs on my 04 Soft tail in 10 minutes. No removing anything but the plug wires . But you did a great job and a nice how to video
Yeah, it makes it a little more work for sure! Appreciate ya!
No worse than Harley always placing the oil filter in that guaranteed to make a mess location. Poor design.
BobsGT235 Your right Bob, no mater what you use it still leaks down the front of the motor
Taking the fuel tank off is easy peasy and so much easier than it used to be. Take it off.. clean everything up . 5 minutes.. you'll get so good at if you do it often is automatic..
You should do more how to vids. Man this is the best one on m8 touring by far. Nice work.
Thanks Michael, appreciate ya!
Nice video, having worked on cars and trucks for years this looks easy on my new to me trike. Thanks for the video.
Sure thing! Enjoy the Trike my friend.
Thanks! This is helpful. Especially the torque values. 👍👍 have a good one!
Glad to help ppuntrotzooi!
Great video, saved me a bunch of time! I did use an air compressor to blow out some of the debris down in the plug holes prior to pulling the plugs
Glad it helped Nat.
I want to see the unedited version taking off the plug wires! Seriously, do you use dielectric grease on the wire? I find it easier to get the boot off. Great video as usual!
You are correct. The dielectric grease is a must for water repelling and ease of removing the boot.
Thanks Ed, the plugs are 2 years old so they actually came off as easily as the video shows. I haven't used any grease on the wires. Have you experienced trouble getting the wires off?
@@TollesonLife I use it for: 1) water repellent, 2) ease of getting boot off, 3) fighting corrosion. There have been occasions where the boot was really tight.
I find the harley brand works well. I use it on every electrical connection. There is also ACF50 of your from the aircraft mx world but the harley stuff works well.
Nice professional job!
👍
Good deal, no bs. Straight to the point. Well done sir. Any coolant service videos ?
Hey Jimbo, no coolant services videos as of right now. Time to change yours?
No worries. Yea just waiting on the dam manual to show up .
Great descriptive video. Much appreciated.
Glad it was helpful Phil!
Very good instructional video!! 👍🏽
Glad it was helpful Jeff!
after plug wires removed, before removing spark plugs blow out all sand, ect out of spark plug holes. GOOD VIDEO
Great video! Very informative. I really appreciate the step-by-step instructions. Keep them coming!
Glad it was helpful Doug!
I didn’t know the 107 had 4 plugs in them my wife has 2017 trike with the 107 . I really miss your riding videos hope to see some this summer. Take care stay safe .😬👍
Appreciate ya Steve. Yeah, we had 2 long trips canceled due to the Covid 19. Planning one in late July!
Good I always enjoy the bike trips . I really the Saint Augustine trip. Thanks, be safe 😬👍
Followed your instructions and was all good but before the 50amp fuse removed had to turn ignition on with FOB present or the alarm sounds. Cheers
Thorough video. Thank you
Thanks Rick!
Great video. Well done as usual.
I appreciate that Scurlock Life!
Your Videos are very well done. I dislike the ones with 15 minutes of bla bla bla before getting into the job.
Tech tip use a piece of 3/8 fuel or coolant hose to remove the plugs simply crack and loosen with the ratchet and turn them approximately a half turn and stab the spark plug with the hose and twist it out the plug will stay in the hose when reinstalling simply put the plug into the hole with the hose rotate counter-clockwise until you feel a click then rotate the hose in until it stopped turning then tighten to spec. I Change a lot of spark plugs in the equipment that I work on. Also I would submit that you used too much antlseize jmho awesome and very informative video by the way. One additional thought since there is a torque value range and you put anti seize on the threads that technically means the threads are wet and a lower value in that range should be used again jmho
Thanks for the info Timothy!
spark plug boot remover - perfect for M8 is only $11 on Amazon and worth every penny. Showed mine the HD dealer and he bought one.
Thanks JD!!
Excellent video.
Thank you very much Bad Bob.
Thank you , excellent video, will use this when I upgrade my wires,
Great!
You did some nice clean job there, I liked and enjoyed it & OMG
WAITING FOR THE NEW VIDEO
Thanks Lewaaolislam! Have a couple coming. About to head to Sturgis, SD for the largest Motorcycle Rally in the US.
@@TollesonLife Best best of luck
Thanks for the video. It made taking off my fuel tank easy and efficient!
Sure thing Tyler, glad it was helpful.
Excellent!! Nice job brother!!
Thank you! Cheers!
Hi, I was getting ready to do mine for the first time and was wondering did you put your bike in service mode before you started?
No I didn’t Rick. Good luck on the job!
Another good one, we’ll explained and very helpful.
Glad you enjoyed it Ted!
Hi great video. After how many miles did you change the spark plugs?
Thanks Scolarichris! The books says every 30,000 miles. But I usually change them at 10-20,000 miles.
I followed along and the job done.. not bad at all. One interesting fact I found with the original plugs, they were not even close to being within spec... from the factory no less!?
Glad the video was helpful! Sorry to hear about the original plugs.
GREAT info! ... Loved the informative video! Thanks.....it is in my Harley folder!
Glad it was helpful man!
Great step by step video. It was twice as easy (or half as difficult!) on my Twin Cam 103! Love that garage...
Lol! I hear ya hogdriver!
Nice video? One question: how long till the engine stall after the grey conector unplugged? I’m waiting for 10 minutes! 😳
Well done man well done.
Thanks bro!
Really enjoy your vids bro.
Thanks jwrappuhn71!
Nice job, thanks for sharing!👍
Thanks for watching!
Good video ! How many miles did you have on those spark plugs ? Thanks for sharing !
Hey Paul, I had 10,000 miles on the plugs. The book recommends every 2 years or 30,000 miles so I hit the 2 year mark first. Thanks for watching!
I highly recommend using high temperature anti-seize. That should be a copper based and color.
Thanks for the tip FOG it!
Thanks for a great informative video, very detailed
Glad it was helpful!
Great Job, Thank You.
Thanks for watching!
Light dab of anti seize on plug threads, torque to lower end of spec torque value to prevent over tightening. Light amount of dielectric grease to inside plug wire boots to help with removal next time, boots sometimes stick to the porcelain. Before removing plugs, blow area clean with shop air . Very small dab of anti seize on bolt threads at reassembly. Prior to photos, notes - YES. Be sure plugs are ion sensing on newer models, too.
Nice video, but the construction of the motorcycle seems not to be so service friendly?
Yes, you are right
Thanks for the video, I haven't changed the plugs yet on my 2017 RGS, but the mileage is saying it's time. You don't use dielectric grease on the plug wire boots? Just curious.......
I should have Jan. Just left it off this time.
Another excellent vid; thanks.
Thank you Oscar!
Nice Video! Do you know if this procedure would be the same in a Heritage 2018? And what lubricant did you use in the new spark plugs?
Guilherme, not sure about the Heritage, I used some anti-seize lubricant for the plug.
@@TollesonLife thanks!
Man that is alot of antiseize.
Doesn't lubricating the threads change the required torque spec?
hello beautiful video, u a question how many km do you change?
Hey Robert, I change the plugs every 10,000 miles, the book states to change at 30,000 miles.
Hi. As this is a fuel injected engine, is "purging" the gas line a part of the process on a 2019 Ultra Limited?
First time putting in new plugs?....How many miles?
Hey Rich, I just follow the book on most of the stuff, HD recommends changing plugs every 2 years or 30,000 miles. This bike has 10,000 miles on it.
Nice work. When will you be doing another long distance ride video?
Thanks Scott! I had 2 long rides canceled due to Covid 19. One was to New Mexico and the other to Iowa. Next ride is late in July to Illinois, around 800-900 miles and the Key West, Fl in September.
Tolleson Life thanks for the reply! Yes, Covid 19 has certainly thrown a spanner in the works for all our plans, hopefully you get back out on the road in July. I really enjoy watching the videos of your trips with your brother and your mates. Be well and stay safe!
Another great video 👍
Appreciate that Ken!
Di-electric grease on spark pug boots before re-install, and probably just a tad less anti-seize - a little goes a long way.
Thanks for the tip JD!
I was reading every two years it is recommended to change out the plugs. Ive had bikes my whole life, this seems way too quick. I can see if I had 20k+ miles, but I only have 7100 thoughts?
Hey Kickin Asphalt. The Harley book for my model says every 30,000 miles. I just do them a little sooner. I think you are rolling fine with 7100 miles.
Short Rubber hose that fits over the plug to get it started helps a lot
Great idea! Thanks for the tip!
Nice job there bro
Appreciate it B T!
I love it when I'm told its easy.
How many miles are the spark plugs good for?
Pasquale, my book states every 30,000 miles, I do it every 10,000.
@@TollesonLife Thanks, I took my 20185Harley Road Glide in for the 10k service, they checked the plugs and said they were fine. the book i saw said 30k or 2 years. I guess my plugs must be OK since they had the chance to change them and charge me but they did not!
I had a P/N of 31600085 jotted in my Harley M8 notes...any idea what the difference is with that given in the video (31600012), please?
Just the video I need. Thanks
Glad I could help Jim!
I'm looking to change a damaged spark plug wire on my Milwaukee 114. How do i identify which wire to order from Harley?
Thanks for video ..👍
👍👍
@TollesonLife I have streetbob, 2020, soon I will change them...
great video buddy
Thanks Rat Fink!👍
Use the right tool for the job ,,, Lisle 51250 Spark Plug Wire Puller ( use for the deep plugs )
I went and bought one from your comment, that thing is fantastic. No more worrying about messing up the wires.
hello, please what size is the key to the sparkplung?
TY now i feel more confident to DIY
Very good!
Nice presentation, but it certainly changes my mind about buying a new bike. My opinion, it's ridiculous to have to pull a tank just to change the plugs.old school for me...thanks.
I hear ya my friend.
Ha,correction I bought a new R.King any ways.
Do you know where to get a service manual? I can’t find a current one for the touring bikes.
Hey Prometeus1979, I had to order mine from the local Harley Dealership. Good luck my friend.
Thanks Buddy
You forgot to apply spark plug boot/dielectric grease to the spark plug boot and tip of the plug. Makes removal of boot much easier.
Thanks Richard, Ive never used that in the past but will next time!
You were lucky to get them off. One of my Screamin eagle wires tore right out of the boot. Luckily I had the original stock set lying around til H-D was able to get them. I even had a boot removal tool and took off the seat. I've since learned from a master tech that the MocCo has a special tool they send to the dealerships just for that. Was told by another stealership it was available to the public. Lying fuckers...it's made by Lisle, part #51750. $22 at Home Depot. Specifically made for the M8. Since then I use the spark plug boot/dielectric grease. No issues.
Great video, thanks 🙏
Sure thing Thomas!
Quick question.. if I’m just replacing the cables (aesthetic purposes) there is no need to remove the tank.. correct? (2019 Breakout 114). The instructions seem like overkill for just changing cables..
Hey Altomar Home, I'm not really sure about the Breakout. It shouldn't be that difficult to change out the cables but again, I'm not sure about your bike and how they are ran. Best of luck!
Great job thx alot
Thank you too!
Thanks great video
Appreciate ya Tom!
Quick Tip. Blow plug holes out with an air line. before taking the Plugs out (could be o stone in there)
Thanks for the tip Bob!
I have a problem with my 2015 roadglide, when I turn the knob to on position takes me to enter pin right away even with fob present, and no headlight, no fuel pump priming , no infotainment, nothing any idea what can it be? Battery?
Hey Isaac, sorry for the delay, been on the road….yes, I’d replace the battery in the fob. Let me know if that does the trick.
@@TollesonLife
Nothing put new battery and no go, how about the Bcm?