@@keeganhache6667 What would recommend for me to get a new engine? I've had 2 BBR 66/80 that were good. 1 BBR 66/80 that l put 3cylinders and 4 different positions in and different mags and replaced ignition coil 2or3times and it never has run right a 4 different carbs (the ones that come with the kits). Have had the phantom, it lasted 48 miles and seized up. The 100MAX which ran great it just started getting hard to start after turning it off. And had a scratch in the cylinder and bicycle engines don't sell parts for rebuild.? The engines last 9 months to a couple weeks (not including the phantom which was 6 heat cycles and almost 1full trip to town and back 37 miles) are the zeda 80s any better than BBR stage 4 engine?
Keegan, that old short rod, short stroke crank, do the magnet shaft have a thicker diameter making it hard to even press fit a new magnet on the crank?
hey man i have a question im getting a new engine because my previous 80cc engine blew up so im getting a new 100cc one im just not sure if it would work because my 80cc had 16:1 final drive and my 80cc had 44 tooth sproket will be using same sproket and chain 315 chain whatever it means and my 100cc new engine will be 18:1 transmision will this be compatible please help i may have more questions
Really needed this info bro for a minerelli build 🤙 much apreaciated
Glad I could help bro that’s why I make these videos
Thank you.I thought there were just 3 rods. I knew there was some differences in thickness of the weights,but not position of the rod pin.
Thanks for the informative video 👍👍
Glad it was helpful!
Thanks again Keegan. What is your favorite China doll engine.
Probably the 49mm iron sleeve cylinder because it got me into port work
@@keeganhache6667 What would recommend for me to get a new engine? I've had 2 BBR 66/80 that were good. 1 BBR 66/80 that l put 3cylinders and 4 different positions in and different mags and replaced ignition coil 2or3times and it never has run right a 4 different carbs (the ones that come with the kits). Have had the phantom, it lasted 48 miles and seized up. The 100MAX which ran great it just started getting hard to start after turning it off. And had a scratch in the cylinder and bicycle engines don't sell parts for rebuild.? The engines last 9 months to a couple weeks (not including the phantom which was 6 heat cycles and almost 1full trip to town and back 37 miles) are the zeda 80s any better than BBR stage 4 engine?
@@keeganhache6667 also, what is the 49 iron sleave called
@tiger7777 just get a Amazon engine put good crank bearings in it and don’t waste money on a engine with just a sticker
@@keeganhache6667 thanks
Keegan, that old short rod, short stroke crank, do the magnet shaft have a thicker diameter making it hard to even press fit a new magnet on the crank?
Some zeda-80 are 38mm. I never go off rod anymore. Only measure to know what you have.
What are the better engine case seals?? I replace my bearings with the 6202ks 3 thank you for that
Viton I got them thru Smolik
I wan't advice. Please tell me that C3 toleration ball bearing for Higher temperatures for crankshaft is necesary or not. Thanks you
Short for the Piaggio, long for the 60mm Farmertec jug.
hey man i have a question im getting a new engine because my previous 80cc engine blew up so im getting a new 100cc one im just not sure if it would work because my 80cc had 16:1 final drive and my 80cc had 44 tooth sproket will be using same sproket and chain 315 chain whatever it means and my 100cc new engine will be 18:1 transmision will this be compatible please help i may have more questions
Well as long as their both 2 strokes it should be fine there’s like 3 different 100cc kits on the market right now
Also 37mm cranks
Yup!
Skyhawks are the best motors just my opinion