Thanks for the video. I was curious if this has dual polarity like a normal relay? I'm trying to set a motor to auto reverse at a specific time interval. Would I need to use a normal relay in conjunction with this device in order to achieve the outcome?
Hello Mr. Shamshiri, this video was very informative! Also, thank you for the tour you gave me at Ontario Tech! I appreciated your attention to detail in your description of the labs available.
Pv & Sv usually used in controllers like temperature controllers. Pv = Process Value (for example temperature measured in the oven). Sv = Set Value (target temperature for the oven).
Robojax.. how robust do you consider this unit? I am planning to use this in an offroad vehicle. Is there a way you could suggest to help it be more robust? Example in combat robots, RC applications and similar devices they have sorta homebrewed potted similar electronic devices... Filling the whole inside with Hotglue. Some have spraying insides with various mixtures of homebrewed silicon mixtures etc.
Is there any way to Fix the T2 time - so that it is always limited for safety ? Or to remove options? Can this be done using Tx and Rx on the rear ? Could you make a video describing how ?
Thanks for the video , I have a 24V DC versoin and I am trying to get a 24 volt DC water heater working through one of these and I can set it up , get the power to come on , runs through the P1-5 on / off programme ( on for 5 seconds off for 15 ) but it doesn't put out any power whatsoever , any ideas, I was wondering if the 300watt dump load is too powerful.
2 things I noticed in this video, 1) the light came on before you even hooked up the wire and 2) there's no way the light would have worked the way you hooked it up (the hot wire coming from the timer can't be hooked to the negative of the bulb because that's reversing polarity and it won't work that way). However the wiring for the timer is correct it just wouldn't work the way you had the bulb hooked up
I want the timer to have a default setting of 4 second delay then turn on for a long time say 8 hours - I don't need more than one setting - So if I switch the 12 volt power on and off (key switch) then what will be the default setting? Does my question make sense
So this relay does not deliver any power from the power supply but only serves to complete a circuit? The 12 volts is only for powering up the module then? Other than the power required, what difference would the 24v have from the 12v?
Will the timer start when power is applied? For instance, in case of power loss, will the timer start when power is restored? Or do you need to press a button to start the timer after power loss.
Now can you set your on time for 30 seconds and off for 6 hours or does the on off have to be in the same time setting as in the on and off both have to be in seconds,min, or hours. I need mine on 30 sec off 6 hours
you made me watch the video. Why would you both are the same? do we have only ONE time? no. We have T1 and T2 which means you can set time for both. Yes there are device with single time then we know it must be the same.
Hi, if you module is AC, then connect AC. if it is 12V or 24V DC, then connect the appropriate voltage. We have operating voltage and load control. the load can be AC or DC doesn't matter.
Hello Thanks for the video. Can you help me on the following: I have 2 Air-conditioning units which I don't want to have them turn on (takeoff) at the same time as if that happens the main circuit breaker switch trips. Therefore I need some sort of a delay-On device that receives signals from the two thermostats of the two AC units and then pass them to there assigned magnetic contactors one after the other with a time difference between the two to prevent the units from turning on at the same moment which will lead to MCB tripping. Waiting for your valuable answer. Regards,
Hello Mr. Shamshiri, please, is it capable multiple different commands in a one line? e.g.: 5sec on - 30sec off - 1min on - 30min off - 1hour on - 3hour off... Thanks.
Hello, I have explained all feature of this. If you watched it fully and did not find what you were looking for, then it can’t do it. So please watch fully.
hello hi, what if im not using the powerload at S1 and S0 ? can i connect the Life wire with S1 and Neutral wire with S0 and by using the T wire connection to the load
The timer is .1 second minimum not 1 second. Is this an error? The advertisement for these say .1 second. This is important if used as a spot welder controller
not needed because you don't deal with those. if they burn you throw this module and buy another one because the components are more expensive than the module.
sadly looks like not going to get a reply. will try anyway. what do you call the pin thingy added to these wires to plug into each of the four spots? coming off the bottom is NOT going to work for my set up. Anyone got an idea on how to turn wire input 90 degrees to point backward instead of straight down or other configurations? any kind of adapters you can plug into this screw type terminal block? Are the block sizes denoted by color. I see some are green. some are blue. etc. ???
I don't understand. I have demonstrated and shown all features. if decimal point is possible in some values you should have seen it. if something is not possible with you change it UP or Down, then it is not possible.
@@robojax I thought you have an idea how to set. Because we can clearly see in the picture that it have a decimal point. I have one of this device and i need to know how to use the decimal point. Thanks anyway 👍👍👍
I came across videos on youtube that said a time delay relay can be used to "latch" pulsing power by way of a time delay relay set to 2 seconds to "keep a power signal open". That is, until the trigger is removed. The idea is I will use this kind of relay to power a side view camera on my car to send video to my monitor by using the right and left turn signal wires on the turn signal switch. Can this device facilitate a looping effect via the 2 second delay pulse my turn signals get until I move my turn signal to the neutral position?
@@robojax Thanks for the reply. I looked at an instruction manual for a different relay and it had a 12v input (low/high) and it's ground. It had an input for the source trigger and it's ground. and then there were 3 output connections. one for power to the device and it's ground. No idea what the third thing was. So apparently (according to that manual) the intermittent trigger is what makes the time delay relay work, and depending on the delay time - will periodically turn on or off the device. My issue was how the device would stay on continuously with a trigger that powers off and on automatically. But it seems the 12v constant power is what turns on and off according to the timer. And that is what keeps the device on while the trigger is active. Thanks
Thanks a lot for this vedio. I have a need to light a bulb in case my water pump is running more than a specified time (more than 30mins). Can that be done with this ?
All features has been explained if you watch it carefully, you should know how to use it for your own purpose. I don’t remember anything about this item and have no ideas where I put it.
Robojax La meilleure chaine de Module Chinois ! tu devrais afficher la consommation MilliAmpére de tout les modules que tu présente ! en commençant par ce module ? tu crois qu'il consomme moins que un arduino uno r3 en veille?
Parce que nous travaillons avec du courant alternatif et que ce module est également utilisé en haute puissance comme une charge de 5 A ou plus, le courant de 200 mA qu'il utilisait pourrait être négligeable avec 5000 mA ou même avec du CA. C'est pourquoi je n'ai pas pris la peine de regarder la consommation actuelle. Arduino consomme moins de 30mA (je viens de mesurer). Celui-ci a un affichage LED et chaque segment consomme 10mA. Merci.
@@robojax , Merci à toi Surtout , ça répond exactement à ma question , je vais partir pour mon projet sur un Uno. Merci bonne continuation et longue vie à ta chaine !
The links are now in the description of video but here for you =======Purchase this module ==== from Amazon: amzn.to/3f5cEtV from Amazon Canada www.amazon.ca/dp/B06X3YSXY9/ Purchase from eBay: www.ebay.ca/sch/i.html?_nkw=0-999+dual+LED&_fosrp=1 Purchase from AliExpress: www.aliexpress.com/wholesale?catId=0&SearchText=0-999+dual+LED
I only connected the power supply, a button to turn it on and off and a speed regulator even if it runs very slowly because I need more power than speed given by the characteristics of the motor. It's correct? Thank you
@@robojax I want to use it in my pc.. I am planning to use it when power back in my home i want to set 30s time after 30s automatic power on my pc But the problem is my pc use 750W. Is it handel it??
Can anybody give me the settings for this scenario? I want to switch on my 12V DC water motor .. 1 hr per day only. i.e. using this timer my 12V dc motor will run automatically for 1 hour per day . And this has to reoeat everyday
You can use Real Time Clock (RTC) module to have precise control on time, then trun ON or OFF a relay. Use Arduino which is cheap and you will have full control . I have full series of videos. here is one alarm ua-cam.com/video/ykgXKUuvtbE/v-deo.html 2nd one ua-cam.com/video/7hBtXdoaAOY/v-deo.html and thirs one with display ua-cam.com/video/gz9xqvRroDY/v-deo.html good luck
I have shown all possible features. you better watch the video without skipping. if you watch it fully and did not find what you wanted, then it can't do it. I always go through all features of the device. Please watch it go get answer. Thanks.
Have you watched it? If I have not shown it , then not possible. I never leave such important feature. Besides relay is mechanical and 0.1s is very fast and I might not be able to get good result. Before relay turns on it will go off. Please watch it fully.
Good evening, I wanted help setting the parameters. I should set the timer for 7 hours and I would like every 20 seconds to work and 20 seconds not. My device controls a sardine mincer for tuna groundbait. How should I set it? Thank you so much for your help and for your kindness.
Hi, I have not left any explaination out. If you watch the video and did not find the features you are looking for, then the module can't do that kind of thats. so please watch it again.
Thanks for the video. I was curious if this has dual polarity like a normal relay? I'm trying to set a motor to auto reverse at a specific time interval. Would I need to use a normal relay in conjunction with this device in order to achieve the outcome?
Very good one. Already to using this
Thank you
Hello Mr. Shamshiri, this video was very informative! Also, thank you for the tour you gave me at Ontario Tech! I appreciated your attention to detail in your description of the labs available.
Hello Samuel, You are welcome. I am glad you liked my tour and tutoring.
Àa1 Lol
Wa'alaikum salam... Brother... I am from Indonesia.... GBU....
Salam Alaikum, welcome to Robojax channel. I am Ahmad, from Canada. Nice to meet you.
Pv & Sv usually used in controllers like temperature controllers. Pv = Process Value (for example temperature measured in the oven). Sv = Set Value (target temperature for the oven).
Thank you for sharing that.
They probably used the same enclosure used for temperature controllers.
It could also mean that Pv stands for primairy voltage and Sv stands for secondairy voltage
@@RhondaKlok or primary value and secondary value,, 😅
Can this module be programmed to simply shut off the load after 3hrs?
Thank you .
Robojax.. how robust do you consider this unit?
I am planning to use this in an offroad vehicle. Is there a way you could suggest to help it be more robust? Example in combat robots, RC applications and similar devices they have sorta homebrewed potted similar electronic devices... Filling the whole inside with Hotglue. Some have spraying insides with various mixtures of homebrewed silicon mixtures etc.
Thank you for this video. Now I can use it ☺️
The module can be triggered remotey, for example with a sensor?
PV means present value
SV means set value
Thank you! Very useful
r
Is there any way to Fix the T2 time - so that it is always limited for safety ? Or to remove options? Can this be done using Tx and Rx on the rear ? Could you make a video describing how ?
Hello Mr. Shamshiri, Thanks and regards.
You are most welcome
Thanks for the video , I have a 24V DC versoin and I am trying to get a 24 volt DC water heater working through one of these and I can set it up , get the power to come on , runs through the P1-5 on / off programme ( on for 5 seconds off for 15 ) but it doesn't put out any power whatsoever , any ideas, I was wondering if the 300watt dump load is too powerful.
it has relay. when it turns on you should hear click. Listen to it and if it doesn't click, then either relay or the module is faulty.
Thanks for that
you are welcome.
Thanks for the video. Rally appreciate it.
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
I also relay appreciate it.
2 things I noticed in this video, 1) the light came on before you even hooked up the wire and 2) there's no way the light would have worked the way you hooked it up (the hot wire coming from the timer can't be hooked to the negative of the bulb because that's reversing polarity and it won't work that way). However the wiring for the timer is correct it just wouldn't work the way you had the bulb hooked up
AC like home outlet does not have positive or negative and you can connect it in reverse. It has live and neutral wires
@@robojax yes but in the video it said it was an automotive bulb, those are DC
I want the timer to have a default setting of 4 second delay then turn on for a long time say 8 hours - I don't need more than one setting - So if I switch the 12 volt power on and off (key switch) then what will be the default setting? Does my question make sense
good video i needed to know how to wire it thanks
Glad it helped
perfect...videos
Thanks
So this relay does not deliver any power from the power supply but only serves to complete a circuit? The 12 volts is only for powering up the module then? Other than the power required, what difference would the 24v have from the 12v?
hi there , thank you for your demostration. does the P1 -4 can you set the time in minutes instead of seconds? thank you sir
any of the programs can be set to any value up to 999 hours.
@@robojaxcan you set the obe time to seconds and the other time to hours? In one Programm p4 for example?
Will the timer start when power is applied? For instance, in case of power loss, will the timer start when power is restored? Or do you need to press a button to start the timer after power loss.
In power loss the timer is rested. But the program stays.
@@robojax I'm sorry I do not understand your response. Do you mean the timer is reset? Does it start to count down when the power is restored?
Now can you set your on time for 30 seconds and off for 6 hours or does the on off have to be in the same time setting as in the on and off both have to be in seconds,min, or hours. I need mine on 30 sec off 6 hours
you made me watch the video. Why would you both are the same? do we have only ONE time? no. We have T1 and T2 which means you can set time for both. Yes there are device with single time then we know it must be the same.
Hi I have one exactly the same do I have to only use Dc Power or I can connect on AC , thanks
Hi, if you module is AC, then connect AC. if it is 12V or 24V DC, then connect the appropriate voltage. We have operating voltage and load control. the load can be AC or DC doesn't matter.
Hello
Thanks for the video.
Can you help me on the following:
I have 2 Air-conditioning units which I don't want to have them turn on (takeoff) at the same time as if that happens the main circuit breaker switch trips.
Therefore I need some sort of a delay-On device that receives signals from the two thermostats of the two AC units and then pass them to there assigned magnetic contactors one after the other with a time difference between the two to prevent the units from turning on at the same moment which will lead to MCB tripping.
Waiting for your valuable answer.
Regards,
Hello Mr. Shamshiri,
please, is it capable multiple different commands in a one line? e.g.:
5sec on - 30sec off - 1min on - 30min off - 1hour on - 3hour off...
Thanks.
Hello, I have explained all feature of this. If you watched it fully and did not find what you were looking for, then it can’t do it. So please watch fully.
@@robojax Sorry, language barrier. :-)
hello hi, what if im not using the powerload at S1 and S0 ? can i connect the Life wire with S1 and Neutral wire with S0 and by using the T wire connection to the load
Hello sir, can this timer controller set for 24 hour
Didn’t I show it? I hour is 60 minutes and one.so 24x60 =1440 minutes or use seconds 26x60x60 =86400
I suspect PV = Primary Value, SV = Secondary Value
You be you are right.
The timer is .1 second minimum not 1 second. Is this an error? The advertisement for these say .1 second. This is important if used as a spot welder controller
Also tell us the ics or microcontrollers which are used in the product while product reviews.
not needed because you don't deal with those. if they burn you throw this module and buy another one because the components are more expensive than the module.
sadly looks like not going to get a reply. will try anyway. what do you call the pin thingy added to these wires to plug into each of the four spots? coming off the bottom is NOT going to work for my set up. Anyone got an idea on how to turn wire input 90 degrees to point backward instead of straight down or other configurations? any kind of adapters you can plug into this screw type terminal block? Are the block sizes denoted by color. I see some are green. some are blue. etc. ???
Sir how to put decimal point to the timer?
I don't understand. I have demonstrated and shown all features. if decimal point is possible in some values you should have seen it. if something is not possible with you change it UP or Down, then it is not possible.
@@robojax I thought you have an idea how to set. Because we can clearly see in the picture that it have a decimal point.
I have one of this device and i need to know how to use the decimal point.
Thanks anyway 👍👍👍
What happens if the power goes off.
The timer save the last program or not
Of course it keeps the program. However the timing will be resetted .
I came across videos on youtube that said a time delay relay can be used to "latch" pulsing power by way of a time delay relay set to 2 seconds to "keep a power signal open". That is, until the trigger is removed. The idea is I will use this kind of relay to power a side view camera on my car to send video to my monitor by using the right and left turn signal wires on the turn signal switch. Can this device facilitate a looping effect via the 2 second delay pulse my turn signals get until I move my turn signal to the neutral position?
I waited to see if someone replies. I just watch the video and I believe you should get your answer by watching the video fully without skipping.
@@robojax Thanks for the reply. I looked at an instruction manual for a different relay and it had a 12v input (low/high) and it's ground. It had an input for the source trigger and it's ground. and then there were 3 output connections. one for power to the device and it's ground. No idea what the third thing was. So apparently (according to that manual) the intermittent trigger is what makes the time delay relay work, and depending on the delay time - will periodically turn on or off the device. My issue was how the device would stay on continuously with a trigger that powers off and on automatically. But it seems the 12v constant power is what turns on and off according to the timer. And that is what keeps the device on while the trigger is active. Thanks
Thanks a lot for this vedio. I have a need to light a bulb in case my water pump is running more than a specified time (more than 30mins). Can that be done with this ?
that is exactly what you can do with this. watch and use it for your own purpose.
Hola me puede decir como hago para que encienda cada 8horas y trabeje por 8 0 10 segundos ??
All features has been explained if you watch it carefully, you should know how to use it for your own purpose. I don’t remember anything about this item and have no ideas where I put it.
Robojax La meilleure chaine de Module Chinois ! tu devrais afficher la consommation MilliAmpére de tout les modules que tu présente ! en commençant par ce module ? tu crois qu'il consomme moins que un arduino uno r3 en veille?
Parce que nous travaillons avec du courant alternatif et que ce module est également utilisé en haute puissance comme une charge de 5 A ou plus, le courant de 200 mA qu'il utilisait pourrait être négligeable avec 5000 mA ou même avec du CA. C'est pourquoi je n'ai pas pris la peine de regarder la consommation actuelle. Arduino consomme moins de 30mA (je viens de mesurer). Celui-ci a un affichage LED et chaque segment consomme 10mA. Merci.
@@robojax , Merci à toi Surtout , ça répond exactement à ma question , je vais partir pour mon projet sur un Uno. Merci bonne continuation et longue vie à ta chaine !
Hi, where to purchase,,,these timers in india...
Hi, the link is provided in the resources page. The link is in the description. you ban get it from AliExpress, eBay or Amazon.
Can this device memorize the program?
Yes
12 hrs on, 12hrs off :)
Sir pls give the link for buy this product
The links are now in the description of video but here for you
=======Purchase this module ====
from Amazon: amzn.to/3f5cEtV
from Amazon Canada www.amazon.ca/dp/B06X3YSXY9/
Purchase from eBay: www.ebay.ca/sch/i.html?_nkw=0-999+dual+LED&_fosrp=1
Purchase from AliExpress:
www.aliexpress.com/wholesale?catId=0&SearchText=0-999+dual+LED
You didn’t reply?
I only connected the power supply, a button to turn it on and off and a speed regulator even if it runs very slowly because I need more power than speed given by the characteristics of the motor. It's correct? Thank you
Sir i like u
Thank you for not skipping the ads and keep watching them. This will help me a lot.
If I want to set it to be cycling
( OFF for 2 hours and ON for 15 sec.) and repeat itself
it is called loop. if it has loop option, I should have shown it. watch the video fully as I don't remember what I did in this video.
show us how to program it to switch n after two and half hours. please
set to 150 minuets
Bunun Türkçe anlatımı yok mu ?
sir give me a schematic diagram more power thank you
This is not about schematic. It is a microcontroller that needs software to program. It is secrete of the manufacturer.
What is the maximum output of it?
output of what? if you are looking for power, I have explained the relay. There is no other output.
@@robojax I want to use it in my pc..
I am planning to use it when power back in my home i want to set 30s time after 30s automatic power on my pc
But the problem is my pc use 750W.
Is it handel it??
Okay then please watch the relay pier rating section of the video and compare it to your pc power . I am sure it can do it
Can anybody give me the settings for this scenario? I want to switch on my 12V DC water motor .. 1 hr per day only. i.e. using this timer my 12V dc motor will run automatically for 1 hour per day . And this has to reoeat everyday
You can use Real Time Clock (RTC) module to have precise control on time, then trun ON or OFF a relay. Use Arduino which is cheap and you will have full control . I have full series of videos. here is one alarm ua-cam.com/video/ykgXKUuvtbE/v-deo.html 2nd one ua-cam.com/video/7hBtXdoaAOY/v-deo.html and thirs one with display ua-cam.com/video/gz9xqvRroDY/v-deo.html good luck
The title says "... 0.1s- ...". This is not true, because the timer does not support measurements of less than one second.
which time? I believe if you can set it, the system will trigger the cycle at that time .
Sir how to set 2 hrs off 5seconds on
I have shown all possible features. you better watch the video without skipping. if you watch it fully and did not find what you wanted, then it can't do it. I always go through all features of the device. Please watch it go get answer. Thanks.
Can ypu show me the setting of t1 is seconds and t2 is hours
I have shown all settings, if you don't see it then it is not available.
How to set 0.1 second?
Have you watched it? If I have not shown it , then not possible. I never leave such important feature. Besides relay is mechanical and 0.1s is very fast and I might not be able to get good result. Before relay turns on it will go off. Please watch it fully.
HOW TO SE T 3 HRS OFF AND 6 SEC ON? CNAT FIND IN THE VIDEO
If it is possible, please have explained it. If not possible then you can’t find it. So watch carefully. I don’t remember anything about the video.
At 6:30... massive rookie error... black is neg, red is pos... stupid.
please watch again. you may have missed it.
WhatsApp no
sorry I have no time .
Good evening, I wanted help setting the parameters. I should set the timer for 7 hours and I would like every 20 seconds to work and 20 seconds not. My device controls a sardine mincer for tuna groundbait. How should I set it? Thank you so much for your help and for your kindness.
Hi, I have not left any explaination out. If you watch the video and did not find the features you are looking for, then the module can't do that kind of thats. so please watch it again.
@@robojax in case I can program it that every 20 seconds it is on and 20 seconds off continuously. It's correct? I think this can do it. Thank you
Can you explain me better? I can do it? Thanks. I don't speak very well the english language