Motion Sensor Light [ DIY ]
Вставка
- Опубліковано 21 тра 2019
- Motion Sensor AC Light [diy]
In this video, we will see how to make PIR motion activated light.
Things required:-
1) PIR Motion Sensor Module
2) Resistor
220 ohm
3) Transistor
2N2222
4) Diode
1N4007
5) Relay 5v
6) Power Supply 5v dc
(USB Charger/Mobile Charger can be used as power supply)
7) AC Bulb Holder
8) H Type Screw Terminal Blocks (optional)
-----------------------------------------------------------------------
-----------------------------------------------------------------------
Diagram:_-----------
drive.google.com/open?id=1lqV...
----------------------------------------------------
Other NPN Transistor that can be used
drive.google.com/open?id=1wrx...
------------------------------------------------------------------------
PIR Module Jumper Setting:-
drive.google.com/open?id=1pYc...
H: Repeat Trigger Mode:- In this mode light will be continuously ON if there is motion and when there is no motion light will turn OFF after delay time.
For example; If the delay time is set to 10seconds then, Light will be continuously ON when motion is detected and when you leave the detection area the Light will turn OFF after 10 seconds.
L: Single Trigger Mode:- In this mode Light will turn ON when motion is detected and light will turn OFF after Delay time. Light will turn OFF after delay time even if you are present in the detection area and again after some time sensor module will start detecting any motion
Turn ON the circuit, wait for 30 to 60 seconds now sensor will start detecting any motion in its range and act according to the mode selected. [This module will only detect motion done by any warm body such as human or animals]
Mode can be selected by adjusting the Jumper,, how??-- pull out the jumper, you will see three pins now put back the jumper to the H side or L side leaving one of the pin blank.
Sensitivity Adjust:- we can adjust the sensitivity or detection range of the sensor by adjusting the preset @ 0:21 . The detection range can be adjusted between 3 meters to 7 meters.
Delay time adjust:- when you leave the detection area Light will turn OFF after some delay; this delay time can be adjusted by rotating(clockwise or anticlockwise) the preset @ 0:22 .
This delay time can be adjusted between 5second to 300seconds.
Both the preset can be adjusted by slowly rotating it clockwise or anticlockwise; You can use a small screwdriver to rotate these presets.
-----------------------------------------------------------------------
PIR Motion Sensor Module
www.banggood.in/custlink/mvDv...
Relay 5v
www.banggood.in/custlink/DDDG...
Transistor 2n2222
www.banggood.in/custlink/mm3D...
H Type screw terminal
www.banggood.in/custlink/KKmD...
-----------------------------------------------------------======
Thank You for watching;
Hope you like this video
Please LIKE SHARE SUBSCRIBE & COMMENT.
Have a Beautiful day.
----------------------------------------------================== - Наука та технологія
Thank you, this circuit is working. Thank you so much.
The íl p
M.
How many watts was your bulb?
Sir light bandh nahi honi chahiye eshke liye kya karna chahiye
I followed everything exactly but the bulb turns on as soon as switch on the power and stays on like a normal bulb, I had tested the motion sensor before using it, can't understand the problem, can someone please help? My 5v power supply provides about 5.8 v maximum, is this too much for the 5v navinex company relay?
@@ethicalhacker1 same problem for me bro.
UA-cam has several videos, but this was the best explained...5 stars to you, i made one light outside my main door and its working fine. Thank you.👏
सर मेरा नाम कमल कांत है मुझे 10 पी आर आई सेंसर कंप्लीट बने हुए चाहिए आप कितने का देंगे मेरे को मेरा नंबर
92127 19814 है
How many watts was your bulb please?
@@nischalthakur1892
कितने के मिले
@@nwankwocharles1130 *LOOK LIKE 5 WATT.*
As others have stated, one of the best examples of this type of circuit.
Clear & concise (given it is not narrated), with a nice clean, professional looking build.
What a comprehensive explanation with detailed instructions even in the description!
This video is the best. Very properly demonstrated without any confusion. Very neatly done. Thanks.
Thanku sir....Electronic meri hoby hai...isliye bahut chanal ko follow krte hai aur video v dekhte hai....pr aapne itne ache se Wireing ko explain kya hai...ki aap ka bataya koi v project banana...bahut easy ho jata hai....thanks.
explains everything very easily... awesome keep going sir...
It's working.. you are a star 🌟
👍Professional touch can be seen throughout the video. Keep it up🙏
Very good job man!!
Superb explanation
Thankyou
good explanation Nice 👍
Very nice video! Thank you.
great work, thanks 4 sharing
Wow.... It's really true!!! 100% working...
Awesome work. 👍
I assembling this ,very good ur videos
Muito bom ! Simples e claro.
Ganhou mais uma inscrita. 👍👍👍👍👍
You do it nice & clean. You gave me a new idea also. Thank you so much.
..And this was a Perfect and detailed video after many..circuit working perfectly..thank you very much..!!
nope
thanks! It helped me a lot, your videos are well explained! success!!!

Simple way. Easy way to understand..
سلام ، تشکر ، خیلی عالی بود
Thanks this circuit is working and I using in my class project
Thank you so much.it was my final yr project,worked well.also pls give circuit description to add to my project report
The best video on this topic.
Verry well explanation👍🔔🙏 6:50
Highly helpful
Thank you so much bro itni acchea tarike se samjha ne k liye
TQ Somuch 🙏Sir This is very use full vedio
As others have mentioned this is one of the best videos detailing this DIY project. Thanks for posting! Do you have a video (or can do one) that details how to wire this with a plug socket instead of the light? I want to DIY a motion sensor that I can plug lights into (regular light bulbs like the ones shown in this video). I need to power a bunch of lights not just one bulb so want to plug a power bar into the motion detector. I can't seem to find anything. Your video is the closest I have come so I now know how to wire the PIR but I'm not sure how to wire up the plug socket portion of it.
Thanks a lot
Es un trabajo excelente. Gracias.
Analog rocks!
tu me sauves la vie pour mon MagicMirror :)
Very nice 👍
Good idea
So Clean And Neet
You can use bc 547 which i think is more common
And the resistor could be 1k ohm too I had 470ohm i used that
good work,
I want to replace the H terminal with another that you recommend
Hello good afternoon, your video is very interesting and it helps me a lot to carry out a project that I am carrying out. Do I have a query, with this practice could I connect a diaphragm pump that works at 12V?
I want to know why to add diode. How to work diode on curcit. Thanks you sir. This is best one.....
So clear
Hi, I am doing a similar project to you and I was just wondering what light bulb you used?
I can use many pir at once?.I will use it on the stairs.
I need to make this device for intrusion detection in farms, for the case I need it to cover a longer range. Is there any PIR sensor which comes with longer range? Or any way by which I can extent the range to atleast 30metres?
Can I replace the power supply with batteries.... also can arduino uno also be used to put in the USB
Can we use this same transistor for connecting the pir sensor to an led strip?
Nice video
Working good
Thanks for nice video Sir.
Please answer me, Can I use an 7 watt or 9 watt ac dc inverter led bulb in this holder instead of normal led bulb, because to use in power cut time ?
Can i use 6v relay in this
Can we use triac in place of relay
Anil Kumar Goel
So nice
this is a sample of professional video making.
thanks for sharing 👌👍
Can you explain how does it operate?
Good job
Thanks
Where do you get the light bulb socket?
My usb cable has 4 wires. What should I do? . Should I just use the red and black and disgregard the other 2?
I don't know the internal diagram of relay used but according to me he is connecting the nc and common of relay instead of the coil of relay so how will relay work
Can I use 12 v led light instead of Ac bulb?pls tell
I built the similar circuit but used a different transistor and a different resistor. The circuit works but response time is too slow. What can be the possible problem? us it due to the transistor and resistance or my sensor is faulty? Can u plz help.
Can l use 12v charger
Super
Sir, can you please explain how to make a 12" automatic exhaust fan for kitchen?
Can i use 12 volt relay and 5 volt power suppely
Can I use Bc547 transister this circute
Sir will it work on door
When I go from door does light will on automaticly?
Nice
Sir do we can use 12 volt realy instead of 5volt
Or we can use 9v battery instead of charger
Whats the use of the transistor
Hi,
If turning light by sensor ,after how much time it will turnoff?
Brother how can its work the output sensor is only 3v low..the relay is 5v I can't understand i have try many many time.How its command from pir sensor output..
Help me pliz.
I have seen many video from UA-cam ..most people are using Arduino.
is this the type of light that turns on automatically if it senses something within its diameter/range? And will it sense other things like toys or metals as well ???
PIR sensor will only sense motion done by any warm bodies, such as Human or Animals.
Boht maza aya
Can I use another transistor and resistor
can I use DL 5V relay sir
What kind of bulb i can use .
I cant find screw terminal what to do?
Can you please tell me how to do without the h screw 2 way terminal
You can use intching relay negative trigger pulse then set your pir sensor to 3sec cut time just like i create in our toilet room once you enter in the toilet automatically turn on the light until you finish shower the time is related in the relay because its latching and when you go out automatically turn off the light 😊
Can you please explain in detail…?
Where can I get the motion sensor to buy...urgently can you help
How should I increase on time more than 6/10min
the system only works when i contact the relay . what is the reason ? any support
This video is great. I want to make one. Please tell me what is the name for the device used for attaching the parts by heating?
soldering iron
very inexpensive max price 350 rupees
Hi, thanks for the helpful video! Do you have any recommendations on how to do the same, but instead of turning ON the light when motion is detected, the light turns OFF please? (no motion = ON / motion detected = OFF).
Thanks again!
use N/C pin of relay in place of N/O pin.
in the video you can see one of the relay pin is left blank, that pin is N/C pin of relay and the brown wire( 4:31 ) is connected to N/O pin of the relay. So, you just need to connect that brown wire to the N/C pin. .Thanks
@@snnyhacksci.5984 Thank you very much for your help! It is appreciated. Will try it out.
@suresh krishendeholl Hi Suresh, yes I had managed to have it turn off the light. We switched the cable on the relay to NC and COM.
@@snnyhacksci.5984 hello thank you for the video it was great I just have one question if possible how the circuit was powered
thank you
Greetings,
I need a help hand. I just connected the circuit to a control unit and my relay its not stable. What can be a problem
Can I use resistor sensor
Какое реле? Нормально открытое или закрытое?
How to operate 12 V LED strip with PIR Motion sensor? Please help.
why diode connect parallel with relay terminals ?
I have used 150k resistor. Not working .. is it becoz of that ?
Can we make this without diode
Can a 6v rilay
6v rilay can ?
I followed everything exactly but the bulb turns on as soon as switch on the power and stays on like a normal bulb, I had tested the motion sensor before using it, can't understand the problem, can someone please help? My 5v power supply provides about 5.8 v maximum, is this too much for the 5v navinex company relay?
I want electrical mini projects
Your video is so nice
But I have a question
Can we join buzzer of 5V instead of light
Replace relay with a 5V Buzzer,,
ua-cam.com/video/K1cmTzp90n0/v-deo.html
Hai, can we remove rrelay in this circuit? What will happen?