YOUR ARE A KING... THANK YOU..I ONLY HAD TO DO THE BYPASS CHARGING FOR FIVE MINUTES AND PLUGGED THE BATTERY BACK IN AND ITS CHARGING WITH OUT THE BYPASS NOW THANK YOU SO MUCH!!!
A massive thank you mate for this explanation and tutorial on how to solve this issue, I tried it 1st time the bypass I didn't have to do for long as I new battery had charge moments later my battery started to charge and work again, a massive thank you again
Thank you very much! It's fix my battery. I tried to short before but it was unseccesful because I didn't keep if longer. When I follow your video my battery first blink red and after about 1 min the light was read. Now charging without any problem. To short I use a wire and conected - to the + like you when charger was connected
@@tipsfeed4707 just did it,its charging now! works :D EDIT: attention: battery made electrical noise at first minutes of charging,like csgo bomb beep faster and faster. then it stopped and did some different noise klaklaklak and then it stopped all noise and continue charging.
My friends sisters boyfriend did this with his moped type bike. Same battery back cluster, he bypassed it like you suggested and brought in the battery to charge it at her house. Her house and both homes attached to the town house were demolished. The other two attached were dammaged by smoke so the whole row had to be torn down. He over charged it accidentally, forgot he was charging it/lost track of time.
My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power? At wat voltage should the board switch off? Any suggestions?
I did this and I revived a dead 36v battery pack. Now my question is the battery on B- and the positive terminal on the xt60 connector shows 40volts but when I test the voltage at the connector it reads 25 volts. I think something is wrong with the BMS and I have an extra one as someone gave me two hover boards with dead batteries for free. Any ideas?
Hi I followed same steps. When short it, can see red light on the charger. But, as soon as I disconnect, it is turning back to green. How long do I have to hold it for? Tried holding it for 2 mins
I tried to by passed but charger light still green. I bought new charger but still green while charge. Does it mean battery died ? I tested battery it 22.1v . Any ideas about that? Thank.
I did a variation I just held a bridge wire between the earth into the board and the battery minus for a while and held it there for a few minutes then when took off the bridge it kept charging must have been just enough to fool the system
in my case it became red for 5 minutes then again green. The hoverboard now has 2 bars so at least it powers up but the charger is still giving me a green light so I suppose it's not charging anything...
I think I'm just going to replace all those cells with high-capacity cells, that way I get more than twelve miles out of it I can double it and maybe twenty-four more
YOUR ARE A KING... THANK YOU..I ONLY HAD TO DO THE BYPASS CHARGING FOR FIVE MINUTES AND PLUGGED THE BATTERY BACK IN AND ITS CHARGING WITH OUT THE BYPASS NOW THANK YOU SO MUCH!!!
wait i dont undefstand
A massive thank you mate for this explanation and tutorial on how to solve this issue, I tried it 1st time the bypass I didn't have to do for long as I new battery had charge moments later my battery started to charge and work again, a massive thank you again
Gracias hermano me sirvió mi sobrino se había puesto triste por que ya no funcionaba pero con tu vídeo pude arreglarlo
Se tiene que hacer solo una vez (como para revivir la bateria dijamos ) o es siempre que la queramos cargar la bateria
you are a clever, clever dude, thank you worked great!
WORKED BUT IT TOOK A FEW MINUTES TO BUILD UP A CHARGE TO ACTIVATE CHARGING ON IT'S ON, BUT IT WORKED! ORAISE YAHWEH!!!!!!!!
Thank you very much! It's fix my battery. I tried to short before but it was unseccesful because I didn't keep if longer. When I follow your video my battery first blink red and after about 1 min the light was read. Now charging without any problem. To short I use a wire and conected - to the + like you when charger was connected
Great, I am happy to hear that!
Hi, what is the voltage reading before doing this procedure? It seems i'm having the same issue, but my battert voltage is 33.4v.
@@jerbyglanida5519 same here we need to buy new one I guess 😢
Thank you man🎉
Thank you alot it work very well
Wkoncu znalazłem jak ja wzbudzić😊😊😊❤❤❤
thanks bro this trick realybworks
Thank you for this helpful video. I did what you described us to do, and it worked a treat. 😀👍
How long do I hold it for
Thansk you broo it is goood 😮😮😮 very very good my bro
Thanks very good explanation i will try tomorrow since I don't have extra wires around :S
Good luck
@@tipsfeed4707 just did it,its charging now! works :D
EDIT:
attention: battery made electrical noise at first minutes of charging,like csgo bomb beep faster and faster. then it stopped and did some different noise klaklaklak and then it stopped all noise and continue charging.
Question, if I just re-solder the negative cable on the PCB board over to the bypass location would that ensure that the problem never happens again?
Yes but it will probably overcharge and it could blow up but you might get more charge time at the same.
My friends sisters boyfriend did this with his moped type bike. Same battery back cluster, he bypassed it like you suggested and brought in the battery to charge it at her house. Her house and both homes attached to the town house were demolished. The other two attached were dammaged by smoke so the whole row had to be torn down. He over charged it accidentally, forgot he was charging it/lost track of time.
My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power?
At wat voltage should the board switch off? Any suggestions?
I did this and I revived a dead 36v battery pack. Now my question is the battery on B- and the positive terminal on the xt60 connector shows 40volts but when I test the voltage at the connector it reads 25 volts. I think something is wrong with the BMS and I have an extra one as someone gave me two hover boards with dead batteries for free. Any ideas?
Hi I followed same steps. When short it, can see red light on the charger. But, as soon as I disconnect, it is turning back to green. How long do I have to hold it for? Tried holding it for 2 mins
How i battry by i have big hoverboard 10 inch tyre
I tried to by passed but charger light still green. I bought new charger but still green while charge. Does it mean battery died ? I tested battery it 22.1v . Any ideas about that? Thank.
do i need to slice into my power cord or can i use just one side of the plug (the hot side)
I did a variation I just held a bridge wire between the earth into the board and the battery minus for a while and held it there for a few minutes then when took off the bridge it kept charging must have been just enough to fool the system
So you put black wire on b- then other end of wire to the earth?
super safed the day
my battery is different,i cant bypass the wire any help?
Please tell me
What do you do if you have 2 wire from battery
If the charger still does not change to red and battery does not what could the problem still be
How long does it take for charger light to go red once the wire is connected to the b- terminal ?
in my case it became red for 5 minutes then again green. The hoverboard now has 2 bars so at least it powers up but the charger is still giving me a green light so I suppose it's not charging anything...
Sir mere 10 inch tyre vala hoverboard hai mai kon se battry buy kru
I have this issue , right out the box 😭.
I think I'm just going to replace all those cells with high-capacity cells, that way I get more than twelve miles out of it I can double it and maybe twenty-four more
My charger doesn't get red light how i fixed it and my hoverboard also not charging
Probably the charger get a new one
At 4:51 did you say 2 hours or 12 hours? I am very confused.
2 hours
Ok thank you very much
Good idea
But the charger will be cut☹️💔
Thank you daddy
Be easier.
To tripod the CAMERA !
Instead of DUFUSING...
Are u n asheboro