Thank you for sharing how to remove a ignition cylinder that will not turn. Your video was literally the only video that demonstrated this. Seven years later and this vid is still a big help to a lot of us.
I have a 2008 Chevy Silverado 1500 truck and the problem with the key not turning in my ignition started acting up about a month ago and has been getting a little worse it seems every week. Today was the worst so I tried some WD 40 thinking that’s all it needed, which did nothing at all to help me get the key to turn the truck on. Very frustrating to say the least. Anyways, I searched UA-cam for a video to fix the problem and came across your video. I never got a price from the dealership but figured if I did take in the truck it would most likely be quite a bit of money to get it fixed. I probably spent and hour or so from start to finish, which included taking it apart and then putting all the plastic panels back in place. Everything went smooth and my truck is back to working like new again. The only issue I had was actually getting the cylinder to come out but after playing with it for a few minutes I finally got it to come out. I also had to remove it twice because I didn’t file the cylinder enough the first time. Anyways, just thought I’d share because this solution really worked!! Thanks for posting it.
great video, ex-mechanic (40+) years,had never worked on late model. this showed exactly how to repair the problem. Also,liked tip about putting gearshift in gear rather than disconnecting battery.
Thank you so much!!! Just picked up a Chevy express with this problem and I was really nervous it was going to cost a lot to fix. Just did your repair and my key turn perfectly now!!!! Thank you so much again!!!!!
This advice worked really well for an 2008 suburban as well. I had to file quite a bit and found the key to be part of the problem. I would recommend trying a back-up key to see if things work better before going through the steps in this video. It turns out I had to do both, but ended up throwing out the original key and making copies of the backup. A side effect of filing too much is that I can now pull the key out while the ignition is on. However, this still beats going to a locksmith.
thank you good sir ,, after 4 years of my key sticking it happened ,, could not get my van running today ,, I watched your video which by the way was very well made ,,, I am glad to report that after 20 min of work ,, my van is fixxed .. thank you again
Great video, I've changed these out before and every mfg seems to be different. This video was a big help. I was able to change out the key lock myself and saved money. There wasn't any screws on the bottom of the column which makes me think it had been changed before. I just snapped off the top plastic piece on the column. Snapping it back was the hardest part and of course something always hangs up in the plastic snaps. I ended up using a rubber hammer to get it close enough. Thanks!
This video showed me exactly how to fix mine except for the part where you remove the cylinder other than that it's a perfect video and worked for me for those that dont know you have to turn the key as if you're starting it then you will feel the pin and push it should come out relatively easily
This was an amazing video! FYI this method also works for 2006 Chevy Express 1500 series as well!! Super informative and on point; greatly appreciated!!
Thanks for the video brother. I have a 2014 Express, and this has been an increasing problem trying to find the "sweet spot" to get my girl to turn over. Will try this weekend
thanks man this video save me money I followed your steps one by one and did it myself it took me like ten with the right tools I have a 98 Express 1500
Hey yo good bro.. .I spent 10 mins to watch the video and took me just another 5 mins get the van back on road and Thank you so much. God bless yo dawg
found this after i bought the rebuild kit from dorman $80 wasted. I couldnt read the # on the old tumblers and put wrong one in which jammed cyclinder in column. had to use pliers as you did!!!!
You are absolutely correct sir. There's also a special tool that is meant just for that. However in this video I was trying to show the absolutely simplest way to do it. It's incredibly hard to film that small hole and to explain in detail how to do it.
You can take a small pick or I used an 16 gauge 2 1/2” finish nail and at the 7 o’clock position you can see the bar that’s catching and you can push it in which is a lot easier than attempting the channel lock method...
I was also able to use a tiny jewelers flat head screw driver to push in that tiny bar to turn the key. Handyman Inside, did you do the rest of the procedure? I fear damaging something that will prevent me from being able to turn the key as it is now.
Thanks man. Was just assigned a Chevy work van and this did the trick! Although I looked for screws for awhile until I discovered the top cover just pops off. Lol. Works great now. Good info👍.
Man you are my hero! I took out my frozen ignition filed the shit out of it and it works like new with only the correct key! Man am i happy! it was just a few minutes ago that i was punching my steering wheel and that didnt fix it. 😂😂 now i can get back to work thanks again bro big time!
What is that black round plastic he removed from ignition before anything called ?? My ignition is missing that little black piece and makes hard to put key ignition when dark. Thanks
I'm not sure what it's called. I think it's just a cover. They are not sold separately. You can buy a new ignition cylinder and it will come with that cover.
Hey there. At 3:44 when you turned the key I saw your dash gauges come to life. You're supposed to disconnect negative cable on battery wait two minutes then do as you are. You don't want the damned computer blasting you with an airbag or go into security mode thinking the vehicle is being stolen.
or you could pick the side bar so you dont damage the shit out of everything...i guess ..leave the quality part to a locksmith......signed...a Locksmith
someone tried to steal my neighbors 2008 g2500 and broke that part that you said to push back it's very expensive at around the 3:56 mark on video and he needs to know the name of that part
Yet another ZERO assist, the hospital lost it and it was 2 months before I got out. My key is gone and I need to pull my van away so I must unlock the steering wheel.
Sorry it didn't help you. How ever the video wasn't about your issue. I doubt this will help but I'll make a video for your problem in the future. The job would require special tools, a Chevy ignition phone pick tool (you can also make the tools) but it's easier to drill the ignition out.
Sorry it didn't help you. How ever the video wasn't about your issue. I doubt this will help but I'll make a video for your problem in the future. The job would require special tools, a Chevy ignition phone pick tool (you can also make the tools) but it's easier to drill the ignition out.
![АЛАУДИНОВ у Скабеевой: эти их ВСУ нас НЕ ДОГОНЯТ 😁 [Пародия]](http://i.ytimg.com/vi/an0anqU4WGQ/mqdefault.jpg)
Thank you for sharing how to remove a ignition cylinder that will not turn. Your video was literally the only video that demonstrated this. Seven years later and this vid is still a big help to a lot of us.
Great detail in your video without a lot of extra talking. Very informative. Thank you.
I have a 2008 Chevy Silverado 1500 truck and the problem with the key not turning in my ignition started acting up about a month ago and has been getting a little worse it seems every week. Today was the worst so I tried some WD 40 thinking that’s all it needed, which did nothing at all to help me get the key to turn the truck on. Very frustrating to say the least. Anyways, I searched UA-cam for a video to fix the problem and came across your video. I never got a price from the dealership but figured if I did take in the truck it would most likely be quite a bit of money to get it fixed. I probably spent and hour or so from start to finish, which included taking it apart and then putting all the plastic panels back in place. Everything went smooth and my truck is back to working like new again. The only issue I had was actually getting the cylinder to come out but after playing with it for a few minutes I finally got it to come out. I also had to remove it twice because I didn’t file the cylinder enough the first time. Anyways, just thought I’d share because this solution really worked!! Thanks for posting it.
great video, ex-mechanic (40+) years,had never worked on late model. this showed exactly how to repair the problem. Also,liked tip about putting gearshift in gear rather than disconnecting battery.
Thank you so much!!! Just picked up a Chevy express with this problem and I was really nervous it was going to cost a lot to fix. Just did your repair and my key turn perfectly now!!!! Thank you so much again!!!!!
This advice worked really well for an 2008 suburban as well. I had to file quite a bit and found the key to be part of the problem. I would recommend trying a back-up key to see if things work better before going through the steps in this video.
It turns out I had to do both, but ended up throwing out the original key and making copies of the backup.
A side effect of filing too much is that I can now pull the key out while the ignition is on. However, this still beats going to a locksmith.
Ray Colline So just be careful on the filling and all the steps will be good?
you have no idea what a life saver this video was for us today! Thanks for doing videos!
thank you good sir ,, after 4 years of my key sticking it happened ,, could not get my van running today ,, I watched your video which by the way was very well made ,,, I am glad to report that after 20 min of work ,, my van is fixxed .. thank you again
THANK YOU, AWESOME JOB IN PASSING THE KNOWLEDGE! SPEAKING CLEARLY, JUST FAST/SLOW ENOUGH TO BE UNDERSTOOD AND INCLUDE THE ALTERNATIVE IF TILT WHEEL!
Great video, I've changed these out before and every mfg seems to be different. This video was a big help. I was able to change out the key lock myself and saved money. There wasn't any screws on the bottom of the column which makes me think it had been changed before. I just snapped off the top plastic piece on the column. Snapping it back was the hardest part and of course something always hangs up in the plastic snaps. I ended up using a rubber hammer to get it close enough. Thanks!
i fixed my dads 08 silverado with the help of this video. Thank you very much for this very helpful video
This video showed me exactly how to fix mine except for the part where you remove the cylinder other than that it's a perfect video and worked for me for those that dont know you have to turn the key as if you're starting it then you will feel the pin and push it should come out relatively easily
Jesus Gutierrez thank you !✌️
This helped a lot didint know how to remove cylinder until I found this comment :)
This was an amazing video! FYI this method also works for 2006 Chevy Express 1500 series as well!! Super informative and on point; greatly appreciated!!
This video saved me from buying a new lock cylinder. Thanks bro!
This video saved my life my ignition was stocked and I watched this video and with a channel lock I could unlock the ignition thank you so much
Thanks for the video brother. I have a 2014 Express, and this has been an increasing problem trying to find the "sweet spot" to get my girl to turn over. Will try this weekend
thanks man this video save me money I followed your steps one by one and did it myself it took me like ten with the right tools I have a 98 Express 1500
Hey yo good bro..
.I spent 10 mins to watch the video and took me just another 5 mins get the van back on road and Thank you so much. God bless yo dawg
Thank you for his helpful video. worked to fix my lock cyclinder problems. saved buying a new part. Thank you
Thank you,worked great on a 2010 sierra
Worked perfect for my 2008 Silverado. Thanks!
Thanks. With the video I was able to switch the ignition cylinder in 15 minutes
I was able to correct my ignition cylinder using your instructions, Great tips! Thank you so much!
found this after i bought the rebuild kit from dorman $80 wasted. I couldnt read the # on the old tumblers and put wrong one in which jammed cyclinder in column. had to use pliers as you did!!!!
Thanks dude. It worked on 07 Silverado.
alex flores si funciono?
jonathan hernandez No todo en UA-cam es Ralidad😂
I am Dead de echo lo hize y funciono ala perfección
Genius im having trouble with my 08 sierra and always thought it was key that was worn out ima try this later life saver thanks for sharing this vid
Thanks sir, saved me hundreds
You are absolutely correct sir. There's also a special tool that is meant just for that. However in this video I was trying to show the absolutely simplest way to do it. It's incredibly hard to film that small hole and to explain in detail how to do it.
Thank you! You saved me!!
Worked like a charm man, appreciate the help
My friend, I thank you!
Thanks good to know I don’t have to replace the assembly.
2012 gmc sierra works perfectly! Thank you for saving me a bunch of $$$$!!!!!
curtis chapman works that?
Doesn't look that hard to do. Thanks Man!!
Thank you bro just fixed mine 2013 gmc sierra
Wow how I love youtube thank you for the help bud this worked great for my work van
Thank you...the new key and hitting it first work! Score...
All he had to do was cut a key by code
You can take a small pick or I used an 16 gauge 2 1/2” finish nail and at the 7 o’clock position you can see the bar that’s catching and you can push it in which is a lot easier than attempting the channel lock method...
I was also able to use a tiny jewelers flat head screw driver to push in that tiny bar to turn the key. Handyman Inside, did you do the rest of the procedure? I fear damaging something that will prevent me from being able to turn the key as it is now.
Thank you for the video that really helped❤
awesome took me ten minutes great video tx so much
Thanks man. Was just assigned a Chevy work van and this did the trick! Although I looked for screws for awhile until I discovered the top cover just pops off. Lol. Works great now. Good info👍.
Great video!!! Thanks for detail step by step explanation 👏👏👏
Saved lots of time and $$$ 👍👍👍
Man you are my hero! I took out my frozen ignition filed the shit out of it and it works like new with only the correct key! Man am i happy! it was just a few minutes ago that i was punching my steering wheel and that didnt fix it. 😂😂 now i can get back to work thanks again bro big time!
Thanks so much for this video!! Going to do it today!! Thank you!!!!
Just saved me a couple hundred dollars, thank you my man
Your video worked perfectly for me ! my key wouldn't turn at all so the key in and the Channel Locks worked perfectly!!🦃 Happy Thanksgiving 2019
Awesome video definitely works
Thanks man, I thought I would have to pay a bunch of money for a locksmith!
Nice, worked like a charm. Thanks
Exelente video brother thanks, God Bless you...
u are the best I have seen on here and thank you it worked for me
This video was extremely helpful. Thank you!
Thank you! Helped a lot
Gracias it worked in my 09 2500hd silverado
Thank you! This is genius.
He rigged it did not fix it butch
Butcher
Awesome video
Thanks Bro this video was on the money and saved me cash
Sandra Ellis works?
Thank you , very helpful
I have a 2011 Chevy Silverado 1500 I did this and it 100% works save me $757 that's what the dealer trying to charge me. I fixed it for free LOL
You are A LIFESAVER!!!!!
Put the key in it. Make sure the block goes down. It's the block does not go down you have to replace the ignition. It comes with a new key.
jelp me a lot thank you so much wow 👍👍👍👍👍👍👍👍👍👍
That's what great 👍👍 thanks 🙏😇🙌
The video is good, I haven't been able to remove the cylinder, I can't lower the cylinder lock, any suggestions on how to remove the cylinder, thanks
Just fixed mine, thanks bro!
Good job
Thanks for the info
Great job bro
only person that will know that if you stick anything in there to start it would be "ME" lol
What is that black round plastic he removed from ignition before anything called ?? My ignition is missing that little black piece and makes hard to put key ignition when dark. Thanks
I'm not sure what it's called. I think it's just a cover. They are not sold separately. You can buy a new ignition cylinder and it will come with that cover.
It sounds like you are saying dorks instead of torx. Awesome video though.
I have a question what is the peace called that you said if it breaks it could be expensive for that ii is broken on mine
immobilizer antenna. Its what senses the chip in the key to start the car
My book say to push the park solenoid so the new key will come to a stop position
Hey there. At 3:44 when you turned the key I saw your dash gauges come to life. You're supposed to disconnect negative cable on battery wait two minutes then do as you are. You don't want the damned computer blasting you with an airbag or go into security mode thinking the vehicle is being stolen.
The problem is the key on these. Get a fresh cut key and that will solve the problem much cheaper.
thanks
or you could pick the side bar so you dont damage the shit out of everything...i guess ..leave the quality part to a locksmith......signed...a Locksmith
yea, this video madde me cringe, I am a locksmith and the advice in this video is terrible...
What if you don't have the key?
Disconect the battery cable.
Somebody needs to cut you a check!!!!
Shouldn't the battery be unhooked?
That's what the book says.
someone tried to steal my neighbors 2008 g2500 and broke that part that you said to push back it's very expensive at around the 3:56 mark on video and he needs to know the name of that part
Thx
you didn't show lock cylinder actually being pulled out
I tried this and the head broke off by the key.
what to do when the key won't turn. to lock
Fuck yeah bro good looking out !
Count get my 08 sierra to turn with this
Nope it fucking broke, thanks
Yet another ZERO assist, the hospital lost it and it was 2 months before I got out. My key is gone and I need to pull my van away so I must unlock the steering wheel.
Sorry it didn't help you. How ever the video wasn't about your issue. I doubt this will help but I'll make a video for your problem in the future. The job would require special tools, a Chevy ignition phone pick tool (you can also make the tools) but it's easier to drill the ignition out.
Sorry it didn't help you. How ever the video wasn't about your issue. I doubt this will help but I'll make a video for your problem in the future. The job would require special tools, a Chevy ignition phone pick tool (you can also make the tools) but it's easier to drill the ignition out.
@@trickerig -- not necessary as the van is headed to junkyard.
It’s not working
My is not goin back
Unhook battery 😂
ghetto fix