How to Replace Rear Engine Mount 2002-2006 Honda CR-V

Поділитися
Вставка
  • Опубліковано 7 лют 2025
  • Buy Now!
    New Engine Mount from 1AAuto.com trq.video/ia-1...
    This video shows you how to install a rear engine mount on your 2002-2006 Honda CR-V. A shaking or vibrating engine, or bucking when changing gears are signs of worn engine mounts.
    This repair was done on a 2002 Honda CR-V EX 2.4L Sport Utility 4-Door 4WD Automatic and the process should be similar on the following vehicles:
    2002 Honda CR-V
    2003 Honda CR-V
    2004 Honda CR-V
    2005 Honda CR-V
    2006 Honda CR-V
    Tools you will need:
    • 14mm Socket trq.video/oaJi...
    • 17mm Socket trq.video/oaJi...
    • 3/8 Inch Impact Gun
    • Swivel
    • Torque Wrench trq.video/o9h-...
    • Block of Wood
    • Liquid Thread Locker
    • Jack Stands trq.video/oFS-...
    • Wire Brush trq.video/om3-...
    Subscribe: / @trq
    Check out our playlist:
    Honda CR-V 2002-2006 2nd Generation: • Honda CR-V 2002-2006 2...
    ⚠ DISCLAIMER:
    While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

КОМЕНТАРІ • 18

  • @TRQ
    @TRQ  2 роки тому

    √ Watch the Video
    √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
    √ Do it Yourself
    √ Save Money

  • @marcus_clarkus
    @marcus_clarkus 9 днів тому

    Thanks for the helpful video. A few tips from my install:
    1. Rotate driveshaft so it doesn’t block the 17mm bolt from coming out.
    2. If the 17mm bolt unscrews but won’t slide out, use a pry bar under the bolt head and a ratcheting box wrench. Pry it out as you rotate the bolt.
    3. When installing the new mount, use a drift punch or any cylindrical object that is smaller than hole to help align the 17mm bolt before install.
    4. I used a small bottle jack instead of my floor jack to lift the transmission because it was easier to fine tune the height and align the hole for the 17mm bolt.

  • @tomcraigmatthews9300
    @tomcraigmatthews9300 2 місяці тому

    Your videos are so helpful and thorough that I buy only your parts now. Thank you.

    • @TRQ
      @TRQ  2 місяці тому

      +@tomcraigmatthews9300 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts! 1aau.to/m/Shop-TRQ

  • @paco-nu5ml
    @paco-nu5ml 5 днів тому

    excelente video,gracias

  • @hemtet5500
    @hemtet5500 6 місяців тому

    Very good video and can you give some idea of the symptoms? Thanks again.

  • @jcorpus209
    @jcorpus209 2 роки тому +4

    I’m eating all these up

  • @roemer7
    @roemer7 2 роки тому +2

    All my 14mm bolts just spin in place. Any advice?

  • @untungtunggaljaya6591
    @untungtunggaljaya6591 Рік тому +2

    A lot corrosion on lower car. Is it the location near beach.

  • @manuelramos4608
    @manuelramos4608 Рік тому +1

    Is this the same as a 2002-2006 Acura rsx??

  • @NTromb
    @NTromb 2 роки тому

    Just wondering how long that TRQ engine mount lasted

  • @gusrojo88
    @gusrojo88 2 роки тому

    Nice! Just got mine from TRQ also!

  • @Andrew-cq3hy
    @Andrew-cq3hy Рік тому

    Having trouble removing 14mm bolts. 2 of them the pressed in threaded pieces are turning in the mount. Any ideas?

  • @mirandamae4483
    @mirandamae4483 6 місяців тому

    Thank you 🙏

  • @glennjeffers9692
    @glennjeffers9692 11 місяців тому

    Where can I get a kit of mounts that aren't a arm and leg

  • @bfg5552
    @bfg5552 11 місяців тому

    Thru bolt only comes out when the driveshaft is rotated so the bolts do not block the bolt removal. Will try it another day.

  • @c_h_r_i_s_t_c_o_r_e
    @c_h_r_i_s_t_c_o_r_e 8 місяців тому

    I’m praying this is similar on the 1998 crv

  • @weknowhisvoice9296
    @weknowhisvoice9296 5 місяців тому +4

    Turn to Jesus people, he died for your sins. Repent of what the New testament describes as sin. Believe the gospel get baptized and obey the teachings of Jesus. The gospel and the teachings of Jesus are documented in Matthew Mark Luke and John. Jesus is the only way to be saved, if you have faith in Jesus through your faith you will live by his teachings. God bless you all in Jesus name amen