Це відео не доступне.
Перепрошуємо.
Simpson Dryer no go (Sirocco/Encore/Maxidry)
Вставка
- Опубліковано 29 чер 2023
- These simple little dryers are all over the place, and are very reliable. If you find it suddenly won't go it is probably from the safety overheat tripping, usually caused by the fan belt breaking. Its a really easy repair to replace the fan (Blower) belt.
Used this video to replace my belt great video. Need to clean inside out how do you remove the back
Inside the drum where filter clips there is a peg you need to pull forward about a cm, then after taking all screws off the back will lift off the drum.
Great video Thank you
Thabks for the video! Ive replaced the belt and its running well, but it now seems like it isnt heating at all. Im wondering if you may know why this would happen and if you have a video on how to change the heating element?
I’ve never had to replace a heating element on one of these before. If the element blows it won’t heat at all, so if you are getting some heat I’d say it’s an airflow problem maybe blockage somewhere.
Sorry just re-red your comment. there is an overheat that trips when the belt snaps, press the red button in the front by the door hinge and try again.
Can you tell me how to get the centre drum bearing out of that same dryer,please the one at the top of the belt,thanks again mate,
if you remove the lint filter inside the drum, then pull on the little plastic tag in the very centre of the filter spigot it will unlock the bearing. Can then pull back panel off the drum with a sharp tug. Rear bearing is plastic on these.
Any advice on how to install a new drum belt on that dryer? Im currently attempting it and it is a nightmare
Lie it on its front. You should see a mark where belt usually sits, tape it to drum in this position with three pieces of tape. Put drum in machine, loop belt around motor pulley and connect spring for tension. Remove tape. Drum will be pulled slightly out of position due to spring tension. Connect back panel to drum first, then align it which will centre drum.
I’ve known quite a lot of people to have these dryers in the past and I suspect the reason why a lot of them have been got rid of is due to this issue, any chance you can do a video on how to replace the clip that holds the lint filter in place Dan?
That clip is actually part of the rear bearing, if I get time in a week I can probably run over that and how to clean out the inside and the fan bearing which is the other common issue.
Hey mate, im working on my fisher and paykel washing machine, how do i drain the machine using contril panel, im just unclogging it from the top, i have a relatively new machine where you have to take the top off from the back
Those machines use a totally different diagnostic system, too much to describe in a comment, ill try and make a video but it wont be until next week sorry.
What year are these dryers from?
I think these particular models was late 90's to 2005 before the eziloader models came out in 2006.
@@lukekneebone9831 Yeah that seems about right. This model is 2004 and I have another one here from 2005
Hey mate, my safety reset button has stopped working all together - looked at the fan belt and doesn’t seem that worn, any advice on how to fix ? It won’t start at all now
It’s probably something other then the safety reset it that case, like the door switch, timer, motor or motor capacitor.
I think people only run their dryers and not often as because of how expensive their power bills cost to operate it except during off peak hours and it’s still not good for the environment unless you have a heat pump (I know these dryers aren’t heat pumps) are they vented out the back or the front?
If you internally clean your dryer every time you get it fixed, or you move house or whatever, and making sure the lint filter is cleaned and it's not overloaded!
This series is rear vented. Yes heat pump dryers save a bit on power use but I wouldn't get a cheap one, and you have to be using it regularly to save enough electricity to make it worth while for the price difference.
@@motrepairs Yes, not that this may be relevant, but turning off unused appliances at the wall will also save electricity as some people think it's off, but it's not completely as the electrics would be live still so thus if you turn it off at the wall, you won't use as much electricity and it also prevents unwanted fried components in power surges!
I have error code 40, do you mind helping me out 🙂 fisher and paykel .
Appreciate you
Im assuming you are asking about Smartdrive not a dryer? Fault 40 is Bowl disengage fault, check the spline in the bowl, under the agitator, and make sure bowl can slide up and down shaft smooth.
@motrepairs it can go up and down the shaft smooth , I removed the whole inside tub out of the machine and it easily lifts up and out and back in again. Any other tips?
Thanks for replying mate.
@@jessemorrison8661 If its not obvious you are going to need to call a tech who is familiar with the later models of smart drives sorry.