Це відео не доступне.
Перепрошуємо.
Use single Cat5 cable to connect 2 PoE IP cameras
Вставка
- Опубліковано 14 лип 2019
- Joe shows you why one cable can connect 2 IP devices.
More information can be concerned our official website:www.fastcablin....
Here you can find more support: www.fastcablin...
If you have any question, tell us in the comment.
Great video. Also, I read some of the questions and I like your answers. Thumbs up to video and subscribed with the Bell. Thanks again.
Thanks for this. I will like to get clarity on this. Once a POE switch supports 12-36 as power pins then this method can work for two ip camera over one ethernet cable.
Yes, as long as it supplies power using 12-36 pins.
I did this in hikvision NVR and it didn't work, any idea
hi, I have a hikvision poe nvr and hikvision ipcs, they dont work with the 1235 commercially available splitters, how must i wire my splitter / combiner, i use t568b standard - great video, also for us dummies 🙂
If you are sure your POE NVR take 45-78 spare pairs to send the power, it will not work with this low cost solution. You might consider the 1 in 2 out PoE extender. www.fastcabling.com/product/poe-extender/
Did you later solve it ?
can you tell us the specific splitter you used and where to order? thank you
This is the link: www.amazon.com/dp/B07G9C7KSL please understand both PoE switch and IP camera should be compatible with IEEE802.3af/at standard. It doesn't work with PoE NVR, as the PoE NVR employ separate twisted 45-78 for power.
@@Fastcabling what splitter would you use then to run from a POE NVR to run two cameras over one cable?
@@eckathewrecka You may have an issue using the splitter to working with PoE NVR. Some of the PoE takes 45-78 spare to transmit the power which means you can't splitter the Ethernet cable. All 4 twisted pairs has been ocuppied.
Hi I try these two adaptor to connect two HIKVISION smart hybrid cameras to a poe HIKVISION NVRbut it doesn't work
If the NVR take 45-78 spare twisted pairs to send the power, it will not work. There are 12-36 and 45-78 4-twisted pairs in UTP cat5e cable. Most PoE NVR send the power over 12-36 together with the data, leave 45-78 not used. The adapter employs the not used twisted pairs to connect the second camera. However, if the PoE NVR take the spare twisted pairs 45-78 to send the power which is seperated from the data. You can't re-use the cable to carry the second camera.
Why with this splitter, when I I test both ethernate cable, there is missing channel one in all 8 channel?
Can you explain "missing channel one in all 8 channel"? The splitter simply seperate your cat5e cable in two group. As you know, only 2 pairs - one group is enough for fast 100mbps Ethernet. If you have choose the correct Etherent PoE switch, the power can be transported as well as the data. You got two group twisted pair after add injector/splitter both side. that is how to power to PoE IP camera.
Hi
I have a lorex NVR with PoE function. A cat 6 cable is running to an outdoor camera and working fine. How can I install another camera close to the existing one please? I mean using the same cat6 cable to connect 2 cameras.
Thank you
I think you will need to move the cable to your switch at the NVR end. If you need two cameras to the NVR, you can't take the POE port from the Lorex NVR. The NVR will detect the connection automatically and only pick one of the IP address (camera) as video feed. In this case, you can connect the cable to up switch to either reuse the cable or add the 1 in 2 out PoE extender at the edge. www.fastcabling.com/product/poe-extender/
I have a SWANN CCTV system and I want to run 2 camera's off one cat 6 cable. I have the splitter adaptors but it still does not work. Do you have any suggestions to how i could get it to work? I am thinking maybe there is not enough power off one cat 6 line for 2 camera's to run so would it be possible to get a power boost?
You might test single camera. if it doesn’t work with single camera, the problem is the PoE NVR use spare pairs to send the power which suppose to carry second camera in your case.
Hi, can you connect two pir cameras to one single cat 6 ethernet cable?
Thank you
Hi I bought a hikvision 4k camera system with 6 cameras. Do I need a power supply? Or can I just plug it in ?
If it is the PoE NVR or PoE switch ready, you can just plug in without using power supply.
Hello. I have a tp link sg1210mp switch and vigi camera. Will work for 2 camera with one cable ?
Yes, it should work. The sg1210mp takes 12-36 twisted pair as power pin.
It didn't work for me. With only one camera plugged into the splitter, it worked. When I plug in the second camera the whole system crashes and I lose all video. All cameras are from the same system. Might be because one of the cameras is a PTZ camera.
Hi, can i use this device to split and add one more camera (in single cable) to my Reolink system?
It is hard to say. It depends on how reolink design his campers. If the PoE power goes through the same twisted pairs 12-36 yes it will work. otherwise It doesn't
Can use this method to connect 2 cameras to nvr
It depends how your NVR design. It is vendor specific. If the PoE NVR use spare twists pairs to send the power (45-78). Not sending the PoE power over data pairs, it will not work.
Hi, Nice video but at the end, not really clear on which POE devices are not supporting this way?
I'm using HIK NVR and I wish to use this system for 2 HIK Poe camera.
Is this way will work ?
It really depends on how HIK design the POE port. If the power is going through spare twisted pair 45-78, it will not work. If I set the automatic connection to each port, it will not work either.
Will this method work with a Tenda TEF1105P-4-63W 5-Port PoE Switch - TEF1105P-4-63W?
This method only can re-use the Ethernet cable, It can save the PoE port. You will need to verify the power pin from TEF1105P is 12-36
I tried connecting the same way but we are getting the green light on the access point but no light on the switch side. and also the access points are not getting detected on the controller
The access points are TP link EAP 115
You may try the PoE switch instead of the original PoE injector because the original POE injector is a passive injector. It takes 45-78 spare twisted pairs to send the power.
I have post the picture on one of my cameras at my front gate and believe one of the cables is damaged, how can I use this system to run one cable and get both cameras working?
I suppose both cameras support PoE (Power Over Ethernet), if this is the case, you should examine how to camera get the power from your PoE NVR or PoE switch. This solution only will work if the POE system uses the same twisted pair (12-36) to transmit the power and data which gives you a spare twisted pair (56-78) to send the power and data to second cameras. The other solution is POE extender which can supply two independent POE ports by using a single Ethernet cable. www.fastcabling.com/product/poe-extender/. It doesn't have a requirement for your existed PoE system.
Hello. Thanks for info. Will this work with 2 Lorex LNB9252B cameras?
It depends on the PoE switch, but not the IP camera. Most of the PoE IP camera accepts power over 1236 or 4578. However, the PoE switch only will choose one path to send the power. If the PoE NVR or switch choose 45-78 to send the power, you can't take 45-78 to carry the PoE for second IP camera.
Hi cn it work with poe injector using ip camera n ap acess with poe injector but not cctv poe switch how if use tp link poe ports ? Cn it work
Yes, but you will need to pick the PoE injector which take 12-36 data pin to send the power. Most PoE injector use 45-78 spare twisted to send the power. It will not work. As the second camera needs 45-78 in the cable.
But my second port is not conventional ip camera just tp link c210 will use poe spliter so cn use poe injector to up the device
i know that gigabit devices need all 8 wires to work but what about poe ip cameras that have specs saying they support both 100/1000 Base-T. Can they work on 4 wires or only 8 wires?
The 1000mbps bandwidth require 4 twisted pair (8 wire). The 2 twisted pair (4 wire) only can provide 100mbps. As I know, most of the IP camera support and only require 10mbps bandwidth, even you consider the traffic peak, 30mbps is more than enough. Unless what you try to use is the Mutiple sensor camera (one camera has several sensor built-in), I really have no idea why 1000bmps do any help. 4 wire PoE only can transmit 100mbps, that is decided by IEEE802.3 protocols.
@@Fastcabling ok so can this camera DH-IPC-HFW81230E-Z which is advertised as supporting both 100/1000mb work with just 4 wires?
@@adyady3099 According to the specification you sent me, the 1000mbps is reserved for mass accessing. The camera allows 20 users accessing at the same times.
Great video! I got one question for my Ip cam system.
My home using tplink nc450 and use PoE injector, is this no way to use 1 cable for 2 tplink nc450?
Thx👍🏻
The tplink nc450 is passive PoE device which means the spare twisted cable has been ocuppied to transmit the DC12V power. There is spare twisted pair you can re-use to send the data or power for second tplink nc450. If the camera is standard PoE, there are mutiple solution to extend the PoE port.
I try this one in below, not working.
7👈fu致这行话₴bZeNcSOg3O0₴转移至👉氵匋寳👈或掂击链街 m.tb.cn/h.40cIR2w?sm=ccfe06 至浏.览览.器【绿联网络分线器盒网线一分二对接头同时连接上网宽带三通换转接口】
Hello, this only allows one device on the internet to run at any one given time and not both at the same time..... does this mean it cannot run 2x IP cameras working at the same time on the network?
This video discuss how to use one existing cate5/cat6 cable to run two PoE IP cameras. If your existing PoE system use data twisted pair 12-36 to transport both power and data, you got spare un-used twisted pair (45-78) which can carry second PoE IP cameras. You still need two PoE ports at the centers. It doesn't require the network port. It is all about double use the Ethernet cable.
@@Fastcabling Thank you
@@Fastcabling Does it work with 2 Reolink cameras?
There are 2 POE modes:
Mode A (endspan) - power is sent together with the data on pairs 1236, meaning pairs 4578 are free.
Mode B (midspan) - power is sent on pairs 4578, meaning data is sent on pairs 1236.
Mode A (endspan)uses 10/100 only.
Does anyone know any Mode A (endspan) poe switches for sale, I need it for myself to install hikvision poe door station and indoor station.
Are you sure it is the 12-36 power pin you need? Most PoE switch use 12-36 as power pin now. You might see some mid-span power solution on PoE injector or not-standard PoE that has remove the power handshaking (force to inject the power). By the way, the mode A has no problem to supply 1000mbps. The latest poe++ take all twisted pairs to send the power 1236 and 4578. The 45-78 mid span was popular because it is simple to separate the power and data transmission at the beginning, but the PoE technology is very sophisticated now.
@@Fastcabling
Thank for the reply.
I have 1 cat6 cable which needs to connect 2 POE hikvision intercom devices. 1 for poe doorbell and 1 for poe indoor station.
Somehow I need to get this to work. Do you know anyway to make it work using 2 port extender?
How can use 1 Cat 5 or 6 cable to run 2 cameras?
You can use the splitter to separate the cable into two or you can use the 1 in 2 out PoE extender. www.fastcabling.com/product/poe-extender/
Can u send the link where to buy the splitter
Could you please send an email to support@golbong.com? The team will provide you the related link. It is important your PoE system is end-span that use 12-36 to transport both power and data. Otherwise, you don't have spare twisted pair to send PoE to your second IP device.
I have 2 cctv cameras and i want to permanently wired to my router but my router has only one socket for the two cameras... how can i do this sir and thank you so much
You will need 1to2 PoE extender. One Ethernet cable in, 2 PoE out. The coming in cable will tak the PoE (power over Ethernet) from your PoE switch or PoE injector.
Can’t understand.
Sorry for the confusion. The cat5e or cat6 cable has 4 twisted pairs. The PoE/PoE+ and the 100Mbps network only take 2 twisted pairs to transmit the power and data. Those two splitter will divide 4 twisted pairs into two group. So you can put two cameras over single cable.