Bell UH-1 Huey - First Test Hover - Indoors
Вставка
- Опубліковано 5 вер 2024
- Bell UH-1 HUEY (Flywing): shorturl.at/xAMT5
Radiomaster TX 16S: bit.ly/2ZKxTeF
RC ERA C189 MD500 Hughes: www.banggood.c...
Goosky S1 Legend RC Helicopter: rb.gy/kfrl4
Goosky S2 Legend Helicopter: bit.ly/3Jgama7
FLYWING FW450 V2 Helicopter: www.banggood.c...
FLYWING FW450 V3 Helicopter: www.banggood.c...
RC Hoonitruck Car: www.banggood.c...
RC Drift Car: www.banggood.c...
Eachine EC35 RTR Flameline 1/14 2.4G 4WD 30km/h RC Car Drift LED Lights w/ Gyro Full Proportional Vehicles Models: www.banggood.c...
FLYWING FW450 V2 Helicopter: www.banggood.c...
FLY WING Bell 206 Helicopter: bit.ly/3rqR2Nq
Eachine E160 Mini Helicopter: bit.ly/2XIaF7a
XK K100 3D Helicopter: bit.ly/38piSDh
Eachine E130 Helicopter: bit.ly/2U2du0F
ALZRC FAST X360 3D Helicopter: bit.ly/36raBxH
XK K130 Helicopter: bit.ly/37DgHfe
XK K110 Helicopter: bit.ly/3i5szZJ
XK K123 AS350 Scale RC Helicopter: bit.ly/30FnXmA
EUROCOPTER EC145: bit.ly/34F5VSj
OMPHOBBY M2 Explore Helicopter: bit.ly/2YaWsQv
OMPHOBBY M2 EVO
iFlight Nazgul5 Evoque F6D Deadcat HD: www.banggood.c... Chimera7 Pro V2 HD 6S: www.banggood.c...
#flywing #rchelicopter #bell #rc #helicopter #flight #unboxing #hover #andrejsturm - Авто та транспорт
Even sounds like a Huey I want one!!!
I can’t wait for the weather to change for the better so I can test my out👍🏽👍🏽👍🏽
very brave
Nice going, I like these, may have to order one.
So cooll, i really want one these too bad i dont have money
Hello, did you perform any operation to calibrate the compass or did you take off inside the warehouse without calibrating it?
Great 👍 you are good pilot 👩✈️
Thank you :)
Stemumj are you getting the V4 and 3d printed rotor parts?
I am not sure, but probably not.
Hi,
I see you recieved this as ARF
can you describe your reciever/transmitter setup?
you added your own reciever?
did you have to modify any settings in transmitter?
I would like better to have the TX16S than buying the provided transmitter in the RTF version.
Thx.
You're gonna make me buy one. Lol! I don't hear much tail noise... Did you change something?
I did't change anything so far. This heli is a V3 version - V3 version FW helicopters have upgraded tail motor&prop combo - the tail prop is larger, shaped differently (to reduce noise) and it spins at lower RPMs and thus the tail rotor noise is reduced compared to the previous generations of FW helicopters.
@@AndrejSturm Well, that cinches it then. Buying one! Dammit... LOL
Hi how did you stop it from shaking on takeoff and landing.
keep going 👍
Very fine !! But you flew indoor with GPS ? 😊
No he flew in manual or 3d mode which is how all RC helicopters should be flown
@@goldenmanuever1176 Thanks a lot ! Is it easy to fly in manual mode ? 😊
Did you need the keep ing throttle stick up while hovering at 3d mode?
Hello Andrej, congratulations to the nice maiden flight!👍
Very nice and scale looking helicopter.
You fly in the blue 3 D mode, is the heli in this mode good to hover or will it very much stick action?
Thank you. In this video I hovered this heli in manual mode ''indoors'' and thus in relatively turbulent conditions. The helicopter was relatively stable, but to keep the heli in one spot I had to constantly make a tiny input corrections which is totally expected in such conditions. So far all I did is this hover test but I have a feeling that it will be a stable flying heli, just like my Bell 206.
Andrej, you mentioned that you hovered " manual" did you use the "ATT" (1400)- setting? I'm a bit confused, because the status LED in the video looked green to me..
Hi, I was flying in full manual mode.