How Upgrade the Oil Cooler line Pipe on 2010 Lexus RX350 Replace install toyota 2GR-FE / leak fix

Поділитися
Вставка
  • Опубліковано 15 бер 2024
  • this oil cooler pipe line are interchangeable to some lexus and toyota
    autopurlieu.com
    Please support me by donating so i can keep making great content.
    Paypal: autopurlieu@gmail.com
    Cashapp: $AutoPurlieu
    Venmo: @Legend_gary
    Thank you
    Join this channel to get access to perks:
    / @autopurlieu
  • Авто та транспорт

КОМЕНТАРІ • 16

  • @rayoh2011
    @rayoh2011 Місяць тому +2

    Hello Sir, Thank you for an excellent tutorial on your 2010 Lexus RX350 Oil Cooler line Pipe replacement! Of 10 or more similar installations on the RX, Sienna, Highlander, etc, your video has the best lighting, cleanest like-new parts, and very easy-to-follow procedures! I have the same car, and I feel very good about doing this job now!

    • @autopurlieu
      @autopurlieu  Місяць тому +1

      Thank you for your support 🙏

  • @greatproduction1198
    @greatproduction1198 4 дні тому +1

    Great job. and really good quality video, thank you so much MAY GOD THE LORD BLESS YOU

    • @autopurlieu
      @autopurlieu  4 дні тому

      @@greatproduction1198 thank you for your support 🙏

  • @andysimpson3142
    @andysimpson3142 15 днів тому +1

    Thank you

  • @luisvirgen4544
    @luisvirgen4544 3 місяці тому +2

    What’s drill extension setup are you ising

    • @autopurlieu
      @autopurlieu  3 місяці тому

      I use a deep socket, extension and a swivel adapter

  • @merica1st76
    @merica1st76 Місяць тому +2

    I crossed treaded the bottom right tread tightening the stud in place and it broke the upper oil pan.I should have took it to a shop😖

    • @autopurlieu
      @autopurlieu  Місяць тому +2

      How bad is it? Was it leaking ? Or wasn’t tightening properly ?

    • @merica1st76
      @merica1st76 Місяць тому +1

      The stud wouldn’t stop turning it snugged up a little, but then got loose again and then a chunk of the upper oil pan where the stud goes dropped to the ground in pieces.

    • @autopurlieu
      @autopurlieu  Місяць тому +2

      @@merica1st76 normally you would go up 1 size bigger and replace the stud then match it with bigger nut. But it will be tough to find a 1 size bigger stud .
      If you think there’s still a bit threads left. You can try to install it back gently and use a locktight .make sure it fully dry so you can tighten the nut into that stud

    • @merica1st76
      @merica1st76 Місяць тому +2

      @@autopurlieu thanks for your input,but the whole hole where the bolt goes is gone it broke in 2 pieces.Do you know if I will have to remove the engine to replace the upper oil pan/the no 1
      . oil pan?

    • @autopurlieu
      @autopurlieu  Місяць тому +1

      @@merica1st76 if your replacing just the oil pan. I don’t think you have to drop the whole engine .
      Dealer or other shop might drop the engine to make it easy for them. Specially if it’s AWD.
      I have dropped the oil pan from toyota Tacoma when doing the front timing cover gasket replacement (I have a video in my channel) without removing the engine from the car.

  • @johnr2297
    @johnr2297 Місяць тому +1

    Hi, How much oil is lost during this procedure?

    • @autopurlieu
      @autopurlieu  Місяць тому +1

      Not too much. Half a quart maybe

    • @johnr2297
      @johnr2297 Місяць тому +2

      Ok 👌 👍 thanks.