2GR-FE Toyota Sienna, Venza, Highlander, Rav4, Lexus RX350 Oil Cooler Lines Upgrade
Вставка
- Опубліковано 8 вер 2024
- If you would like to eliminate the weak point of your 2GR-FE engine - upgrade your oil cooler lines from the rubber to metal. See below for the links.
As an Amazon Associate I earn from qualifying purchases. #commissionsearned.
Also, I personally use or have used the products featured in my links and only recommended them if I feel they are of good quality.
Didn't find the kit on Amazon, but found the original cooler lines (without gaskets):
Genuine Toyota 15767-31020 Engine Oil Cooler Pipe- amzn.to/3Q6SGRJ
For the kit (lines and the gaskets) - ask your dealer for part number - 04004-29131
Original Toyota/Lexus OIL filters for 2GR-FE engines - amzn.to/3Q39md5
Toyota OEM Engine Air Filter 17801-0P051 - amzn.to/3Q5nWkc
Lisle 81960 5/8" Carbide Scraper, 8" (for old gasket removal) - amzn.to/3WDlC6j
Battery charger/repairer/desulfator/maintainer - amzn.to/3HkXQr4
Timing tool for Audi 3.0T engine - amzn.to/3Vy7Otq
Headlight restoration kit:
CERAKOTE Ceramic Headlight Restoration Kit - amzn.to/3NKwomx
Power tools:
1/4" Milwaukee M12 Fuel ratchet - amzn.to/3sBmcUm
3/8" Milwaukee M12 Fuel ratchet - amzn.to/3rJLMY0
1/2" Milwaukee right angle impact - amzn.to/3oGqQQ6
1/4" Milwaukee M18 FUEL Hex Impact Driver amzn.to/3Jk1r6r
Tools:
Triple Square Spline Bit - amzn.to/3Lq398i
Mityvac MVA6851 Fluid Extractor - amzn.to/3sCU2IV
Arcan Underhoist Support Stand, 3/4 Ton Capacity - amzn.to/3Jc2Uf8
2011 here Just failed and I'm glad my wife caught it leaking before it ran dry!
Vert good video, Sir. I watched about 10 of similar jobs, with Highlanders, RX 350s, and Venzas, etc. l find your camera has the best angles, lighting, and details. I also appreciate you took the time to show every step of your work and the patience to explain them! Thank you 👍🎊
To get to the 3 lower tube plate bolts is using flex head ratcheting wrench and access from underneath. It will take you less than 5 minutes to remove 3 bolts and screws.
I have a 2012 XLE and believe I’m not affected despite having the same engine.
and, of course, here is the link to the actual original video from Ahmed (The Car Care Nut) that this UA-camr seems to have "borrowed" from and without any attribution: ua-cam.com/video/hbMzH42cqCI/v-deo.html
This is the lower...i think by d look of it d upper side is more likely to break...idk...good job..and thanks a lot for posting this u earn more a sub an like keep posting..cheers!
Car care nut's channel mentions to not get brake cleaner on o2 sensor. May ruin sensor.
I would say not to get the brake cleaner on the "active" part of the sensor where the holes are and sensing element is. The "outside" of the sensor when it is installed is open to the elements and should withstand nearly anything.
the gaskets are leaking on my Venza, even though it has metal lines. This could be quite the challenge to do without a lift
Thanks! I didn’t see where you listed the new part. Is this from the dealer or aftermarket? Thanks, good job and suggestion.
I showed the part number in the end of the video. Original part only - never an aftermarket for something important like this.
hello would it be possible for you to provide the part number for this cooler line part. i'm looking to do the job on my 2010 toyota venza with the v6 engine?
The rav4s do not have an oil cooler