Racks, Holders, Hooks and Dividers - Tool Chest Building Ep.3
Вставка
- Опубліковано 1 січ 2023
- Like what I do? Support the channel by becoming a member; / @eoinreardon
In this video I continue work on on my hand tool only woodworking chest. Enjoy - Навчання та стиль
Hi Eoin
An old machinist trick for preventing rust in the tool box is to put a block of Camphor in the box. The camphor slowly sublimates(evaporates) and puts a rust inhibitiing coating on the tool. It smells nice also.
Also, dry out a bunch of corks and rotate them through.
My grandad was a plumber from the 1950s to the early 2000s, and when he and I would go into his shed, he'd show me how to use all these hand tools and how he loved to use them, and now I'm a bit older I now love using them. Not to the skill he did though.
That will come in time.
Same here bud. It comes. Just start using the tools on scrap pieces when you are bored. I am starting an ultra simple project; birdhouse!
@@EoinReardon in response to your surface rust issue, in this video, I've been saving up the little silica packets and anti moisture strips, that you find in new shoe and boot boxes, I toss a handful of packets or I staple a few strips inside all my tool chests and draws. It's been helping me for a long time, depending on what atmosphere the tools are being kept in and how long for but a helping hand nonetheless.
Now that’s a tool box to be proud of! In terms of the surface rust issue, I know my grandad just used 3 in 1 oil on the surfaces but he also kept tools individually in small carrier bags, which is a bit of a pain when you immediately want something and it’s wrapped up like Christmas aha
Thanks for the tip. Thats some dedication right there. You often see tools that were kept in their cardboard boxes between uses. Im not sure about that though. Tools are meant to be used not pampered.
@@EoinReardon you’ve just described my grandad perfectly. I now have his Stanley no.4 and it’s still in its original box (well I’m sure the box is there under all the tape aha) and it’s wrapped up in a plastic bag. I can see what you mean by pampered however I think he saw it more as it took hard work to earn the money to own such tools so why not look after them perfectly. Albeit maybe a bit too perfectly aha
@@EoinReardon some tools can be stored in oiled sleeves of compacted cardboard. It also keeps moisture away, especially useful in saltwater marine environments.
If you add a little weight about 1/2 to 2/3 of the way up the chain it might pull it in as the lid closes. Great series!
Paste wax and candle wax are great for protecting the metal on tools. Silica packets left in drawers and corners are nice too! They help reduce the moisture.
Wonderful video as always, thanks!
I use the silica packets and
They seems to work pretty good.
Interesting tip on the desiccant might try that
I was gonna say this too about the silica packets. I’ve been saving them from amazon packages during covid and having a toddler at home. They’ve been great for small drawers, drill bit cases, tool rolls, etc. I’ve been considering using them inside my new plane socks for breaks between projects. My tools live in my garage in a humid part of the American Southeast, so surface rust is unavoidable even with oils, wd40 rust Specialist spray, and paste wax coatings on anything metal over any length of time. Hope it’s working for you too
Eoin: Greetings from Cape Cod. To manage your surface rust: start by cleaning (dust is a precursor to rust - as it attracts and retains moisture. For the same reason, always keep your tool chest closed when not working with it - indeed, you may want to think about adding a "dust-lip", a ½ inch strip around the inside of the lid to help seal the lid from the top.)
I use Renaissance wax and Camilla oil - available thru Amazon - on my chisels and planes But they need frequent application. Given you are working in an unheated space surrounded by typically "soft" Irish weather, you may want to consider spray-on Boeshield - which come from the aerospace industry - that lasts much longer. It's a little pricy, but well worth it - it has kept my cast iron table saw rust free in my garage with just a quick application 2-3 times a year.
Nice job on the chest - I've rarely seen one of these Dutch tool chests that isn't too heavy to comfortably carry by your self. You may want to consider a little folding cradle/cart with caster wheels - as well as some handles on the exterior.
This isn't any advice but: I started watching your videos after my stepdad died in 2021. He loved to make things with wood and he was manx/irish. In the first lockdown he made a Skerries Currach(?) in my back garden. Watching these feels incredibly comforting because I miss him a lot.
Independently of that - I really love the videos. You've got a clear skill and love for the craft, and that's always wonderful to see.
R.I.P
Excellent work, may an old fella like myself recommend spray oiling the inside of that beautiful tool caddy and use some oil cloth around the tools. Keep plenty of dry cloth rags in a separate container and a bit of alcohol to wipe them before each use. Also keep a 00 steel wool to rub the surface rust. Our tools predict our future. May God give you his blessings, my best to you, from an an old carpenter retired in the mountains.
I like paste wax for rust prevention. I could be wrong, but I feel like oil rubs off faster and even evaporates if left long enough. The wax clings well and buffed onto the metal feels better than oil. Love the tool chest!
Absolutely correct about the oil! It turns into a sticky honey coloured mess that I’ve had to use acetone to remove. Just like you I’ve switched to paste wax and haven’t had any issues since - except for being too generous with it at first and then needing to wipe everything down before using my tools again 😅
Thankfully a small tub of wax lasts a LONG time, and after impregnating a rag with it over multiple applications I can now simply wipe tools down with it and not worry about buildup on their surfaces. And I sadly have to store my tools outdoors to face Canadian weather given that I’m an apartment dweller.
Here’s me hoping for a real, temperature controlled workshop someday in the future.
@@Sangrell I work in my garage which is unconditioned. Essentially the same as a shed. Down here in Florida the rust goes crazy. Especially days like today when it’s near 80F and 99% humidity.
@@jmd5687 I feel your pain! The humidity must be unreal - let alone if your near the coast and have to contend with salt in the air too! Here up North the humidity is likely nowhere near what your battling, but even just the unstable temperatures, particularly during season change, or thawing and freezing cycles, always does a number on my tools - let alone my ability to work when it goes from -22f to 10f in under 24 hours 😖
Eoin, make sure you wipe some shellac on the wood dividers and any wood surface that the metal bits of your tools come in contact with. This prevents moisture held,by the unfinished wood from staining/rusting your tools, especially the dividers for the planes. Nice tool chest, you should get lots 2:57 of use from it.
Cheers
Hey Eoin, try a couple blocks of camphor in your box for rust prevention. It evaporates slowly and puts a light coat of camphor oil over everything. Some folks don't like it but my great uncle used it for years. He was a house builder from back in the forties up until the 70's.
hi, great video and toolbox. lid chain, fix it slightly closer to the hindge on lid side and it will fall into box...
Genius, cant believe I didnt think of that myself. thank you so much!
Only 30s in, bit UA-cam put you up as "A Place for Everything, and Everything in It's Place"!! That has been one of my Major Life Lessons!! It never escaped my notice, that my Pappy (Mom's Dad) had everything "At the Ready"... be it by peg-board location or specific coffee can, Pappy's shop was well thought out!!
Love You Sooo Much, Your determination to keep what you do, true to our lineage, is just Greatness! Congrats on WD-40, that is Super Cool!
Im not so nice to my tools, but ive used balistol for awhile and it works pretty good. Im not sure if thats a good fit for your beautiful hand tools though. Some people dont like the smell of it but it gives me good feelings in my shop when i smell it. Good work on your tool chest, you're making all my hand tools jealous.
Love watching this build. All the attention to detail and organization.
Balisol, beautiful stuff. Stop any tool going rusty and will work on any auld yoke
Hi Eoin, I’m a fairly recent subscriber and I’ve really been enjoying you vids, both long and short. I’m probably 30+ years older than you but I’ve been learning a lot. I’ve only recently switched from power tools to hand tools. Anyway, I truly appreciate the time and effort you’re putting into these productions. Please keep it up! Cheers!
Sorry, forgot to mention that your tool box looks fantastic!
Throw a couple pieces of chalk in each compartment of the tool box. It soaks up ambient moisture to help prevent rust
3-in-1 oil is great for oiling tools. A 7 ounce size tin can with a rag tightly rolled up and stuffed inside makes a great tool oiler. Once the rag is in place in the can, just add the oil. It works great and is handy for keeping tools lightly oiled to prevent rust.
Great toolbox!
If you're having issues with surface rust on your tools try rubbing them with some Paste Wax, it's a cheap option and that's what I use on my hand tools to stop rust. Just use a rag or even your hand to apply a thin layer. You will have to reapply it every so often tho. Or use some Boeshield T-9 Rust & Corrosion Protector it works great but, it's a little more expensive than Paste Wax is, about $20 US a can. 👍👍
You have a couple options for oiling your tools and keeping them rust free. You could use Camellia oil, but that seems to be a bit expensive. Alternatively, just mix some grease from mineral oil and paraffin (or even better, microcrystaline wax) to make some quality grease. Another tip would be to put some dehumidifier bags into your chest. They'll scrub small excess of water vapor for months if not years... but you need to change them (or bake them regularly).
I love your videos so much and it's sparked my interest in hand tools! I've enjoyed building (w/power tools) since I was a little girl but I feel this is more my speed, so I'm excited to get my hands on some!
Even unfinished, it's stunning! Happy New Year!!
I love watching your work ❤
I know a lot of oilfield guys over here in the states will use diesel to clean their tools, pretty sure if you soak a rag in it and wipe it on it'll protect them as well. When I clean guns I use this stuff called G96 gun scrubber, spraying it on a rag and wiping it in seems to keep the rust off them pretty well
Hi. I made a Dutch Toolbox (DTB) for my main handtool arsenal. I love it. I went with the removable front. panel. I hang it on the back. I also made some hooks to hang my Bow/Frame Saws off the back.
For my interior, i did not glue anything as I wanted to be able to adjust the contents as my collection... and more importantly, my use of tools changed over time.
Here are some things I did for my kit that might give you some thoughts:
1. A lower case with wheels for extra storage and ease of movement around shop floor.
2. Side handles that incorporated a French cleat concept for side expansion of some shelves and other tool storage. Love it! One side I have a shelf that is designed to hang my cordless Drill and impact driver under. The otherside is similar but hangs hammers, bit braces, and egg beater drills. Both incorporate a dowel pin that secures to cleat yet enables removal easily without tools.
3. Along inside front lip of chest, I made a place for my drill bits. I find it perfect and will add another for screwdriver bits and bobs.
4. Your chest has Doors! Have you considered leverage that for some on door storage? A thought.
I'd be very glad to share some photos if interested.
Thanks for another vid I keep checking your channel for new vids haha
Eoin-great looking box there. I’m enjoying your videos a great deal and the enthusiasm that you bring to your work and your videos. I’m a priest here in the US and I’ve been doing all hand tool woodworking for almost three years now as a hobby and have done quite a few restorations of planes and vintage tools. I’m in Pennsylvania in the USA and during the summer months, I have the same problem with the rust. Don’t let it get to you, it’s just part of the deal. I’d imagine in Cork, its quite humid/rainy. By the way, I have relatives in County Tyrone up in the north. Anyway, try using Rust Free to remove the rust with steel wool and T-9 as a protectant afterwards. Both are made by Boeshield and you can get them online. Use gloves & a mask as they are solvents. All the best! Fr. Sean O’Neill
An awl is my most used tool. I am no carpenter or joiner but I use it often to mark wood, measure the depth of a piece of wood or a hole in a wall, cleaning out the dried glue in a nozzle, getting a screw I dropped from under a cupboard or a crack in a floor board, scraping muck out of a groove, stirring paint/varnish. It's got a hundred uses (and a lot of abuse) and sits in the top of my tool box all the time Give it a clean up along the length and sharpen with a bit of sandpaper every now and then and its good to go again.
I use cheap motor oil on my planes religiously every 2 weeks because my tools are stored in a cold and moist environment. Air tool oil works well too if you have a cheap source, or if you drain the oil from a compressor motor. Thats the best oil in the world, so if theres any tools you dont touch, that stuff will keep it well protected forever.
Nice tool box there mate. For the rust I'd suggest using renaissance wax, it is used by blacksmiths all over the world to prevent rust. It was developed by the British museum after they noticed small rust forming from bees wax.
Hope this helps mate, love the channel and keep up the great work.
My Grandad always had 3 in 1 oil for his old tools. Rub it on when you put it away, and rub away any possible residue when ready for use!
Nice tool chest. To prevent the chain from falling out the front when closed, shorten the chain a little and Move the connection on the lid down a few inches around the the middle instead the front edge. It will still hold the lid securely up right but won't have so much travel when you close it. I rub past wax on my planes and saws from time to time to prevent rust. Works great even in my humid climate, give it a try. Cheers!
This looks great! Could you create a series where you start with the beginner tools we need and then start making. Other episodes where we can learn to make beginner projects with those tools?
Eoin, to remove surface rust like that I use a red 3m scotch brite pad and wd40. You could use a linseed oil dampened rag to wipe down all of your tools to help prevent the surface rust.
I use camilia oil to wipe tools down with if they're not used frequently, it works well but most tools that I have get used often enough...... there may be a better rust prevention type thing that'll work better than the camilia oil that I don't know of. That No 62 bevel up plane is a rare sight in Ireland lad, she's a beaut 😁🤙
Minwax finishing paste wax is really good for cast iron to slow the rusting and it makes the planes sole slicker. just rub a light coat with a rag over all the exposed steel and give it 15 to 30 minutes then give it a light buff with a clean rag. i use it on all my planes and castiron tops and no rust so far even had some water leaked on the table saw but wiped it off quick and no rust.
I’ve found a light coating of 3in1 oil works quite well
Greetings from New Jersey, USA. WD-40 has a product called corrosion inhibitor that is designed for long lasting rust prevention. Also some tool companies make silicone impregnated bags for storing planes which might be perfect for those planes that aren’t everyday users
Hello Eoin I've loved the tool chest build.
As the chest is so heavy. It might be a good idea to build a trolley with a scissor JACK built underneath the chest so you can jack it up high to get it in your car for the fairs this year. Just a thought. Happy New year.
Renaissance Wax, Mothballs, and Zerust vapor capsules are all good items to add to your corrosion prevention plan; decent bang for the buck.
I highly recommend fluid film for preventing rust on long term tool storage. It’s a lanolin based rust preventer,
Great video as always
Thanks Zachery
Raw linseed oil and beeswax paste has worked wonders for me. 2 parts wax to 1 part beeswax by weight. Very humid where I live, the wax has stopped nearly all rust on limited use tools.
Great toolbox!!!! A coat of good oil will stop the rust!!! Your great toolbox should be on some kind of cart to make it easier to move...
Try T9 (Boeshield) for long term storage. I've used everything on (and off) the market; it's my favorite. Cheers from the US.
Renaissance Wax is the very best option to keep things from rusting. It was originally designed to keep museum swords and armor from rusting.
Can't wait to see how it goes in episode 4
You can get packs of silica beads for absorbing moisture. It helps with my air tools in my metal tool box
amazing video
hey Eoin, i have an idea to fix your chain issue, i was thinking maybe affix a lead fishing weight onto it somewhere so when you close the lid, that weight will automatically pull the chain into the box.
A bit of conduit that you use to place on electrical wires will help the chain from bunching up and sticking out when you close the lid mate.
Awesome!
Thank you lad. Cheers!
Wheels ! You are gonna need wheels on that thing !
I've heard good things about BOESHIELD T-9 for rust and corrosion protection on bare metal. I live in a desert so haven't got much first hand experience.
"Nothing like a nice piece of ash!" --Sean Connery
Another great video! Happy new year!
Thanks Jaden, and to you. Onwards and upwards!
Awesome
To minimise the surface rust, I'd recommend applying a finish to the tool chest as well as something like 3in1 oil to the tools. That and taking the time to brush off all the sawdust before the tools go back in, I've definitely noticed sawdust having the biggest effect on rusting the tools in my garage. Oh, and using the tools lots also helps of course 🙂
Can u tell me a bit more about 3 and 1 and how it differs from a normal wax like candle or a lubricant like wd40
Birch wood Casey Barricade. Comes in a spray can and in wipes. It’s made for removing surface rust and protecting firearms but it works well on any metal. I used it on my large jointer while I was repairing it to keep the bed from rusting.
Great tool box, it’s always nice to see someone doing what they were born to be doing, whatever higher power you believe in, they’re happy you found what they gave you.
you can use wax to seal and prevent moisture buildup. there are various brands but you can use candle wax too.
Edit: it may not work as well on the sole because of the more frequent rubbing but if its sitting in your toolbox there for a little it will probably stay sealed
cheers thank you!
@@EoinReardon beeswax works great, and its relatively cheap/easy to find. natural too!
There is a product called Renaissance Wax. Great for metal. Used on swords at a bunch for the Renaissance Faire locations in the US.
Zerust makes products that stop corrosion in drawers and chests. They're nice because you don't need to remember to treat your tools every time you put them back in place.
So, oil for the metal is obviously good, but if you've got moisture issues, you can buy packs of silica gel and throw them in there to keep the inside air from getting to damp
Great vid mate u need a trolly make one on casters try the silica pouches you get in trainers or a dry dyhumidifer to draw moisture away from ur tools
Amazing work! To help with the surface rust on your tools I recommend using the Birchwood Casey Silicone Gun and Reel Cloth Gray. I have been using for years on all types of metal tools keeps things nice and clean and slick. Hope it helps.
The problem with silicone ismifmitmgetsmonmthenwood of,your project, it is hard to remove. There are several spay on wax finishes designed for wood,tools, that protect the tools, and do not transfer to your projects. Paste wax is also a very traditional rust preventative and helps the planes slide easily. Another traditional solution is tallow wax. I use camellia oil, which I have had the best luck with. It does require wiping down the tool after use, or at least once every several months of storing the tools.
To hang up your tape measure, take an old hack saw blade and nail it on each side. Much easier to hook your clip on a bigger flat piece than that single nail you have there.
Quinn Dunki uses a product called Boeshield T-9 - it's a spray on rust preventative. I've never used it but she swears by it. A more easily-available product this side of the pond is probably clear Waxoyl spray.
Glad to see your subs and views blowing up on here too. Get that bag laddd!
Thank you Ryan!
When you get the little packets of silica gel in deliveries etc, keep them and place inside your tool box it will draw the moisture out the air inside the box
Ballistol might be worth a try for rust prevention.
I use electrical termination compound to keep away surface rust, It’s tacky and meant to keep away oxidizing.
I’ve also heard about beeswax but I haven’t tried it yet.
I use paste wax on stored tools to prevent rust and I haven’t had a problem since I started. I’m sure there must be other methods though so I’m hoping to be enlightened and educated by this comment section :)
In terms of the rust there are many things to do.
You can coat the metal surfaces with wax, motor oil, WD40, gun oil etc.
WD40 and gun oils tend to dry out a bit and leave a steady protective coat on the surface (which they are made to do) however it may need to be re applied after rubbing off when using the tools. Same goes for wax.
What I came to love is cold bluing all my tools with a simple gun bluing solution. However this doesn't work on all metals as they have to be carbon based and won't blacken chrome steel for example. 2 coats of gun blue and a 9hour coat of gun oil afterwards leaves good lasting protective finish but the downside is that you may not like having everything in black color. You may also try moisture sucking packets and just throw them into the box but they still may let little bits of rust form as they aren't perfect for an application like this. Hope this helps out.
For rust you could try storing a few packets of silica gel in the chest. if you keep it closed that'll absorb enough humidity to make a difference I reckon. WD40 also have a rust prevention oil maybe they could hook you up once you get that sponsorship 😉
Your timber is absorbing and expiring moisture. Sealing the timber will help stop rust.
There is a product called ballistol. Its supposed to be great for everything metal. Its used on firearms a lot to prevent rust. Yes im American, and we like guns.
Put a little sinker weight on the top part of the chain just past halfway. It should pull the chain in out of the way of the lid front
I've had good luck with paste wax for wood. The key is to reapply every so often. I'm lucky though, my shop is in a nice dry warm basement. Only gets humid during the summer months.
after using, I usualy spray my tools (especialy the one's i don't frequently use) with some wd40 and dry them of lightly with a old cloth, works like a charm
I use Balistol for the tools which I don't need for longer.
Nice
We always used to coat with a thin layer of petroleum jelly - Vaseline in the US. Maybe some bags of silica absorbant to take on the water, and the lid kept closed?
petrolium jelly is a great idea. it would also lubricate the sole. Im just wondering could it be bad for the wood, leave a stain or make it harder to finish with varnish, wax and oil.
@@EoinReardon def finish the wood first. Any toolbox finish should be a seal, not open pore. The gunk that will collect! Love your videos!
@@EoinReardon LOL I was thinking only of your tool box - were you worried about staining projects? Well you are removing the wood first being contacted. But when in doubt, keep a rag and some denatured alcohol on hand, clean b4 use and re-apply after.
Yaaass was buzzin for this episode lad. Ye can get a platform that scissor lifts up like 500kg. It's also on castors... So ye can stick an auld engine or toolbox on it n lift it up, pop it back down n wheel away. Those wheels lock off too. Probably set u back about 100 euros. Work out a way to fix box to it n ur golden. But they come with those anti slip rubber mats so it might be alright just sat on it. Good luck 🤞 🍀
2:11 an electric guitar you say?!?? Please keep us updated about that!!!!
Put your linseed oil on the tools works great
You've done a lovely job on your tool cabinet, but for practicality, I find storing tools inside metal file cabinets on wheels makes a whole lot more sense.
They can be moved around easily and can even be locked.
Heck, all I did there was screw the cabinets onto small piano dollies.
As for rust, try keeping a small open jar of soda crackers inside to absorb moisture. Works like that in a small salt shaker.
Of course, that may attract mice. Worst-case scenario, maybe have to invest in a barn cat.
Ballistol oil works well as a rust preventative
Even knowing you said you want to paint it black, imo, the natural color looks perfect as is, maybe just seal it against water. Yes to casters and side handles. About the surface rust on the planes, either nickel plating or chemical bluing should provide rust protection. (I watch a lot of tool restoration videos on youtube.)
I’d loose the chain and used one of those piston type rods used specifically for hatch covers. No worries then of it coming down on your head or fingers.
Boiled linseed oil should keep your tools from rusting, it's a really light oil and doesn't leave a lot of residue. WD-40 would work too.
You could try balistol, its oil for rifles and more and if you take care of it and rub it in carefully, you should not have any problems anymore
A past wax works great
Aside from wax & oil, you can get toolbox shelf liners that prevent corrosion. Look up "anti corrosion toolbox liner". They work well in my experience.
You could use desiccant pouches. Doesn’t need power but will absorb moisture in the air.
You may need a moisture barrier layer: physical, chemical, or both. An oily rag for wiping everything down may help too. Peace.
Use silica to absorb moisture to prevent rust.
I use turtle wax on my hand saws and hand planes chisel I apply it with 0000 steel wool and buff off but you might need to do it twice a year if the are exposed in the garage cheers lad I enjoy your videos 🪚🔨😃
Hard wax like a bees wax on all surfaces including the wall of the chest. As the tool rub against the walls they will pick up more wax
Hello, idk anything about woodworking but i think if you applied some oil finish in the inside it should prevent moisture buildup.. maybe also make a small cage in the side and fill it with silica packets they are pretty cheap 🤔
You beautiful man, I've been curious about your toolbox in the livestreams and didn't even know there was a series going on about it, so definitely going to check those vids out!
Also Happy New Year, Eoin 😉 Wishing you much deserved growth on your channel for 2023
Thank you Dylan. Im looking forward to getting it finished and on the road. Happy new year to you too.
@@EoinReardon No problem, excited to see the progress on it!
Also, if you mix linseed and beeswax into a paste its great for finishing and sealing things up nicely. Good for waterproofing too, and doesn't require as much maintenance in the future. You can also use linseed beforehand, and then apply the linseed & beeswax paste afterwards once it's all been soaked, but it's usually not even necessary