rx king , repair 2 stroke piston housing | proses pembuatan liner rx king

#rxking #automotive #lathe
rx king , repair 2 stroke piston housing,
repairing the liner of a 2-stroke RX King motorcycle, the process of making the liner hole, inserting the piston housing, and the process of adjusting the piston hole.

[@kholidcoy0781]

Chenel indo yg selalu di tonton orang luar negri, semangat terus bang

[@Masardhi5758]

Joooss tenan mas, baru ini sy lihat vidionya semoga sukses selalu dalam berkarya dan berkah ilmunya

[@KULITEHNIK]

Terimakasih doanya, semoga maseh jg di kasih kesehatan selalu 🤲

[@RayTitske]

Great job nice porting to looks fast.

[@MyZxcvb12]

Looks like it's going to be a powerful 2 stroke. Good work.

[@arealassassin]

Amateur! Never, ever press a liner in cold! Put the barrel in the fire, or on a BBQ, and drop the liner straight in, no pressure, or stress. I have resleeved dozens of barrels this way, and never had a failure! Fire is cheap, a cracked barrel is not!

[@gothoblandong5867]

Ini pasti jos. Baru lihat tukang bubut sperti ini. Tau arah2 lubang aslinya

[@dragonskinstudio]

You do some nice work

[@KULITEHNIK]

Thank you very much 🙏

[@progaragechinskiemotorki]

super sprawa mieć takie maszyny :D

[@royelsa8886]

Mantap ..sukses terus mazzzzzze

[@KULITEHNIK]

Terimakasih boskuh 🙏

[@dhimasprabowo3066]

Clearance antara bahan liner dengan alumunium bloknya dibuat berapa mas biar liner masuknya padet kayak gitu

[@gembelde9133]

Punya ku terlihat mas hehehe
Sehat sehat selalu mass

[@KULITEHNIK]

Terimakasih boskuh 🙏

[@kosasihsasih16]

Mantap

[@ZygmuntKiliszewski]

Good job, congratulations 👌.

[@marcolima5141]

Excelente trabalho

[@sic81]

Muito trabalho mesmo.
Ainda não entendi pq ele não resfriar a camisa ou esquentou o cilindro

[@ks-ek4of]

👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@dolananlas1600]

Nyimak om salam satu oli

[@widodododo8219]

Mantab bank,,,, klo blh tau abang di daerah mana???

[@KULITEHNIK]

Ciamis maseh..

[@LingkungSeniSantriKalijaga]

Ini OB lapis atau full ob? Maaf saya awam. Hehe

[@vilivilian9751]

Excelente!

[@grongkra2203]

Quá tuyệt vời a

[@adventurerofmusic8675]

Does sleeving the cylinder can cause overheating?

[@KULITEHNIK]

I use a thicker cylinder sleeve to avoid overheating, of course with an even polish too

[@adventurerofmusic8675]

Ohh i see. Here in our country they use thinner sleeves even on 4 stroke and the sleeve warped rapidly due to overheating and and bad sleeve metal quality. And sometimes the cylinder block cracks due to sleeve thermal expansion

[@1crazypj]

Before Mahle developed 'chrome' for Porsche cylinders in the 1960's, most 'cooking' two strokes were one piece cast iron (cylinders and fins.)
In the late 70's, cast iron liners were common in two stroke and four-stroke motors with alloy block and things stayed like that until late 90's when 'plated' cylinders became common on motorcycles
Usually, there is a 0.002"~0.004" interference fit, depending if liner is shrink fit or press fit (sometimes both, initially shrunk in then pressed after cooling due to alloy 'shrinking' faster than iron)
If you had problems with liners distorting, they were either not fitted properly, had been bored too thin or were made from old water pipe!

[@1crazypj]

@@KULITEHNIK I noticed that on a different video.
Is wall thickness around 8mm?

[@anangbeng2974]

@@KULITEHNIK Andalan pokoke sampean mas

[@smmotor2991]

Sm motor
🙏👍👍👍😀

[@sic81]

Why you dont freezer the serve?
Or burn the cylinder

[@atwer4]

Ngiritt gas ya bng gak di panasin hahaha

[@gepeng-25gadfbhjhhjn]

Open jasa ganti liner silinder rx king gak bang?

[@cinex0182]

Lokasi dimana om

[@KULITEHNIK]

Ciamis boskuh

[@sigitefendi1504]

di blok nya gak di porting dlu om ?
baru di pasang liner nya , takut turun lobang2 yg di blok pas di bubut ngilangin liner nya

[@KULITEHNIK]

Kita ga ada porting blok menjaga perubahan alur lubang , liner ga akn berubah slama transfer gambarnya bener.

[@djokosetiono2956]

Alamat bengkel dimana

[@memyselfandi3925]

👍

[@pistonku3038]

Cara ngemalnyaa mas tutorialnya mas..

[@KULITEHNIK]

Siap boskuh lain kali saya up, kmarin pas pengambilan gambar kurang jlas jd saya skip 🙏

[@pistonku3038]

@@KULITEHNIK iyaa mas karna ngemal bagi sy sangat penting mas. Karna sering kali ga pas .. Mksih mas
D tunggu vidio selnjutnyA

[@kopihitam3867]

Bg bisa pasa boryng jp racing gk?

[@mancingkali3146]

Habis berapa bang untuk OB macam itu

[@fasullodavvero]

???? quale sarebbe il vantaggio di una simile follia?,a meno che quel cilindro non sia fuori produzione,ma anche in quel caso si poteva ricromare.

[@giovannitermite9854]

Buongiorno, posso avere vostro contatto indirizzo, ho bisogno di ricostruire una camicia per mio motore, grazie

[@alerasa9293]

Bisa pesan bosku,, untuk vikxion old

[@dellafitri9565]

Lokasi mana...bisa psn

[@heryrahmanrahman904]

No wa ada Bosque...

[@KULITEHNIK]

IG boskuh
mas.ferdy.522

[@safyaniqbal196]

Yb 100 sleep

[@agusriyadimakro1976]

Harga proses ob

[@kadalinagaraju334]

Address?

[@adicaprio1341]

Boleh tau alamat'y gk Maz

[@KULITEHNIK]

Panjalu, Ciamis boskuh 🙏

[@pegawaingoprekvespa4262]

No WA Masse

[@gertkristensen6451]

cnc ha ha

[@werkudoropandowo]

matamu kui pekok

[@parvezkhanpathan8977]

Sir appkhase hai

[@mbahjur9396]

Lokasi

[@widodododo8219]

Ada no tlp / WA

[@KULITEHNIK]

IG ,.
mas.ferdy.522

[@maxig7922]

Excelente video colega que opinan de este ua-cam.com/video/ngWBjGON0m4/v-deo.html