2015 - 2022 Audi Q3 Amp and Sub Install
Вставка
- Опубліковано 15 жов 2024
- Parts used linked in the description below!
Watch a full tutorial as a 2018 Audi Q3 will have an amplifier and subwoofers installed to the factory radio. Note this Q3 has been equipped with the factory Bose amplified sound system which will be retained with this install.
This video applies to Audi Q3 models for years 2015, 2016, 2017, 2018, 2019, 2020, 2021, and 2022. This video also includes amplifier wiring, amp installation and testing.
Click here to see how to set your gains on your amplifier!
• How To Set The Gains O...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Parts used in this install (Amazon Associate Paid Links):
*Recommended Subwoofer package: amzn.to/33Whd8y
*CT Sounds CT-700.1D Mono Amplifier: amzn.to/3zbEgH0
*KnuKonceptz CCA 4 Gauge Amplifier Wiring Kit: amzn.to/3zIWXT2
*Pac Audio Line Out Converter: amzn.to/33lRh5u
Disclosure: As an Amazon Associate I earn from qualifying purchases
Parts used linked in the description of the video!
My battery is in my trunk. Would that make it easier.
My son has the same car, we installed 2 10”s this weekend, Skar Amp and Kicker 2 channel LOC. I followed your instructions and it worked great for about 15minutes then faded out. Nothing coming from subs unless gain was raised then it was just a loud violent humm. Removed power fuse, installed back and it worked great again. Then faded out. With radio turned all the way down if you increase amp gain it humms loud and violently.
Do you thinks it’s the LOC?
Yeah, bad LOC. I'd recommend the one we used, or LC2i. Give that a shot.
How did you keep your car from kidding memory or screwing over the Throttle body?
Is it possible to connect some tweeters to also amplify the sound? Or taking the signal from the factory subwoofer can it only be used for another subwoofer?
What if i dont have the factory subwoofer and its wiring man … please tell me which wire to use for the amp input 😢 PLEASE RPELY I HAVE THE same AUDI
Hello, which wire did you end up using?
I used a Kicker line-out converter in my 2013 Q7. The issue I have is that sometimes (most of the time) the LOC doesn't turn the amp on. I can unplug the speaker leads for the LOC input, then reconnect them, and the amp will then turn on.
I have a friend that has the same issue in his Honda accord, but he ended up running a new remote wire from ACC to his amp.
Ever ran into this issue and have any advice for my Q7?
Thanks!
I have a amp and sub installed in my Q5. I was told the car need to be all the way on for the after market amp to work in a Audi. I was told the amp only can come on when the ignition switch is in on position. It can not be hooked to come in acc position is this true. The factory amp comes on in acc, but the aftermarket does not. Any suggestions?
It depends on your line out converter and the features it have
what is the fuse amperage you used between the LOC and 12v factory source?
5 amps is plenty!
I think proper way is connect positive wire not to battery but to fuse box
That line out converter is garbage 🗑️. Full of distortion
Not if you properly tune it using an DD1.
@@ProvoBeastAudio I seen that no more than 2 volts then distortion city
@@ProvoBeastAudio No. The signal is already distorted as it comes from the standard radio which is always crap. You can process it all you want, this system will only make it sound louder. What you need is a direct line level signal from the radio to the amplifier. Or an optical (SPDIF) link from the radio to a DSP and DSP to amp.
Where did you run your rcas from)
From the line out converter.