22/03/22 I've been teaching myself small engine work for the past nine months and am compiling a complete diagnostic process worksheet so I do things in the right order, avoid testing when I don't need to and make sure I don't miss anything. I've searched for and found every video Joe Pace has posted in an effort to assemble all the diagnostic information available for the "Advanced Sequential Troubleshooting Worksheet" (which was mentioned in every video but which I cannot find anywhere). I have seen six parts - F (two parts), G, L, I and O plus the Block Off Plate section but have not found Section H or a copy of the entire worksheet. If anyone has more information or even just a list of what's on section H I'd be most grateful. I'm posting this on every one of the above sections in hopes I'll finally get the attention of someone from Husqvarna like a servicing dealer who is willing to share that information.
Bob Chain saws fuel tanks in general have 2 way venting the should hold 3 to 4 psi and not much more. the amount of pressure they will hold is designed in by the manufacture.
Although this this same principle applies to many fuel tanks, check to see if the manufacturer of the tank has a sticker with pressure testing specs. Boat tanks are usually rated for a max testing pressure of 3lbs on most tanks. You don't want to rupture your tank.
Hi, Joe can you tell me where i can buy the 4 stoke carb from ? i got a 2018 scooter and the carb went bad my brother said, so need a new one, something is broke on it ? can you send me where i can go on a place that sells them ? i have look for months i found lots of 2 stoke cabs but no 4 STOKE CARBS FOR SCOOTERS IT LOOKS LIKE THE ONE YOU HOLDING with TWO HOSES in the TANK to thanks, if can help me Kim
I have a 4 cycle engine on a walk behind lawnmower that has some trouble picking up the fuel. The carburetor is clean. I always have to prime the engine when I restart it. How do I troubleshoot this problem?
Thanks, how do you check a Homelite chainsaw where the tank is part of the saw? It appears to have a brass filter pushed into the plastic body above the tank.
Hi Joe, is it possible for you to send me a copy of the Advanced Sequential Troubleshoot Work Sheet as mentioned in several of your UA-cam videos?BW,Steve
You've been a huge help with your teachings. Thank you
Hello Joe. I found your videos and they are so helpful. I wish you would keep making more videos. Thanks again
22/03/22 I've been teaching myself small engine work for the past nine months and am compiling a complete diagnostic process worksheet so I do things in the right order, avoid testing when I don't need to and make sure I don't miss anything. I've searched for and found every video Joe Pace has posted in an effort to assemble all the diagnostic information available for the "Advanced Sequential Troubleshooting Worksheet" (which was mentioned in every video but which I cannot find anywhere). I have seen six parts - F (two parts), G, L, I and O plus the Block Off Plate section but have not found Section H or a copy of the entire worksheet. If anyone has more information or even just a list of what's on section H I'd be most grateful. I'm posting this on every one of the above sections in hopes I'll finally get the attention of someone from Husqvarna like a servicing dealer who is willing to share that information.
Thank you. good info and to the point.
Bob
Chain saws fuel tanks in general have 2 way venting the should hold 3 to 4 psi and not much more. the amount of pressure they will hold is designed in by the manufacture.
Although this this same principle applies to many fuel tanks, check to see if the manufacturer of the tank has a sticker with pressure testing specs. Boat tanks are usually rated for a max testing pressure of 3lbs on most tanks. You don't want to rupture your tank.
Hi, Joe can you tell me where i can buy the 4 stoke carb from ? i got a 2018 scooter and the carb went bad my brother said, so need a new one, something is broke on it ? can you send me where i can go on a place that sells them ? i have look for months i found lots of 2 stoke cabs but no 4 STOKE CARBS FOR SCOOTERS IT LOOKS LIKE THE ONE YOU HOLDING with TWO HOSES in the TANK to thanks, if can help me Kim
I have a 4 cycle engine on a walk behind lawnmower that has some trouble picking up the fuel. The carburetor is clean. I always have to prime the engine when I restart it. How do I troubleshoot this problem?
Thanks, how do you check a Homelite chainsaw where the tank is part of the saw? It appears to have a brass filter pushed into the plastic body above the tank.
Great tutorial
Hi all! Would you explain me, whats the exact meaning of fuel cap pressure test? Dont quite understend!
Thank you!
Great info, thank you Joe.
Well done and very helpful. Thank you.
does a external tank vent on a strimmer hold pressure theres a line from tant to the vent
Why all the sighs? Are you tired?
thanks mr pace your a good instructor I learned a lot .
Hi Joe, is it possible for you to send me a copy of the Advanced Sequential Troubleshoot Work Sheet as mentioned in several of your UA-cam videos?BW,Steve
Awesome
Thanks