Bosch GTS 10J (fine tuning)
Вставка
- Опубліковано 16 вер 2024
- Bosch GTS 10J construction site table saw. I just own one and just want to share how I set it up.
it's important that I tune it correctly so that it is safer to use and have good and precise results while making.
sorry if this video bores you, it is actually boring but hopefully it helps 😊
Hello Don
Congratulations on purchasing a new table saw!
This table saw looks very good.
I look forward to the success of your table saw.
Thank you so much. Hope I can make jigs for my table saw the way you made yours😊
This video is very very useful. I just bought the same table saw tow weeks ago and definitely I need to do the same adjustments. Geart help and video. Thank you so much . Abdulla from Bahrain 🇧🇭
I'm glad it helps. Keel safe and thanks for watching my friend.
This helped end a lot of frustrating offcuts. Thank you Sir! Subscribed
Thank you so much sir. Keep safe😊
Awesome, thanks for showing this. I ended up making a fence for my saw because the supplied one had trouble locking to square. Other than that, once setup it's a really good saw.
You're welcome brother.
You're definitely not wrong about the 2000 years adjustment. On mine I see there's no fine adjustment (when tightening the bolts they kept pulling the blade out of alignment) so I ended up shimming one of the bolts with a thin washer which luckily got the blade to within 1/1000 of an inch.
Yes bro it's a pain in the butt haha.
2021, most DIYer in the community I know have already upgraded to 10XC, and I'm just learning to fine tune my 10J. Also watched the newer video in relation to this. I just had a bit of a problem with my riving knife.
Thanks for Watching bro. What happened? Not aligned?
Thanks for the info, I've got one of these coming in the next few days and this will save me a lot of fustration, for many of us working away at home who don't have the space and money for a fancy saw we have to make the best of these cheaper saws.
Your welcome my friend. You can check out my other videos about this table saw. Thanks for watching and keep safe.
Thank you, Don! I'll be going over my saw this weekend, weather permitting. : )
Your welcome Jason. Hopefully the weather will be ok. Take care.
Just ordered this TS, magandang fine tuning video.. thank you sir
Salamat kaibigan, glad it helps. Enjoy your new TS
really good fine tuning vid. ngayon ko lang nalaman what those screws infront are for. thank you master kambal
Hahahaha. Welcome brader. Pasensiya medyo boring at trying hard mag english🤣🤣🤣
@@DonDIYProject it was exactly how it should be. Kung ako yan baka puro pacute lang😂 though kainis i fine tune si 10J. With the retail price, should have been plug and play na. I'll wait for your tune up of the miter gauge. Hahaha
@@alvinadonis3953 I already did a video about the miter gauge.
ua-cam.com/video/UV-50I_MTSQ/v-deo.html
Just a quick fix, I just put tape on the sides. Dipende na lang kung gaano kakapal tape na gagamitin mo. Its better to use a non-friction tape pero pag tingin ko ng presyo hahaha, ang mahal pala. So just use what's available, and it will work just fine.
2000 years later cracked me up :)
Hahaha. Sorry about that. But it's the hardest part of the process so I did a separate video of how to adjust it. Hope this could help.
ua-cam.com/video/Stt8JWrne2I/v-deo.html
@@DonDIYProject Cheers! I just bought the same tabe saw few days ago and I'm just starting with the work :)
@@KotRyszard great!. Feel free to ask if you need some help.
@@KotRyszard and hope you subscribe to my channel so you could see my other videos.
@@DonDIYProject thx m8, will do. I see you make very informative videos.
very detailed compared to other videos here in UA-cam
Glad you liked it my friend. But still I didn't tackle one important part, and that's the hardest one. so I did another video on that, which is the blade alignment. Here's the link and I hope it helps.
ua-cam.com/video/Stt8JWrne2I/v-deo.html
Thanks for Watching my friend.
Thanks, Don. Very helpful and next on my to do list!
Thanks for Watching my friend. Glad it helps.
Don DIY Project looking forward to more useful videos!
@@johnpace5774 thanks and take care.
What i cant really find is a better miter for this saw, normal table saws has a track of 19mm this one is 16mm..I was searching all over the internet and could not find something better than the supplied one.
You're correct, that's why I just put some tapes on the runner to make a better fit.
Ficou show de bola parabéns
Nung una akala ko Chicano, Pinoy pala! Thanks boss
Hahaha. Salamat sa panonood kapatid😊
Armature lena hai GTS 10 J
6:13
The part I most wanted to see you skipped :(
after loosening the bottom screws what did you do to adjust the blade parallelism
Sorry because it really took some time to adjust. Sad to say that there's no micro adjustment, I just give it a light tap then tighten the screw when it's already aligned .
Yup, quite sometimes. It took me 3 attemps. My lucky way: I have to loose all 4 allen screws at both end. Use dial gauge and put zero. Then tighten 1 allen screw only at one side end only. Whatever value read on dial gauge just keep it. Then tighten the other screw. Make sure while tightening the value doesn't change much. I was lucky it dind't change. After that ZERO the dial gauge.
Then move dial gauge to other end and also rotate your saw blade to that side. What surprise me was the dial gauge change only -0.01mm. Now here is a bit tricky. While tightening the screw keep an eye on the dial. Make sure it won't change much. If not stop and tighten the other one. By doing that i managed to get -0.02mm at this end and 0.00mm at the other. So i guess i was lucky.
Before that, my blade tilting at 1.25mm. Fuhhh
Just uploaded a video regarding blade alignment.
great video, is the fence at 90 degrees to the table?
Actually it is slightly off, about a half mm,
I'm planning to improve it one of these days, but for now I can live with that.
Sir good morning, pagnagadjust po ba ng pagparallel ng blade sa miter slot sabay po ba luluwagan ang front and back allen? Or pipili lang kayo ng luluwagan?
Pwede na likod lang, ang hirap luwagan sa harap.
Could you please show the blade alignment process in some more detail?? This will be most helpful for people like me
Love to show it to you. I'll let you know as soon as I get a chance to make a video for that.
Regarding blade alignment as promise
ua-cam.com/video/Stt8JWrne2I/v-deo.html
@@DonDIYProject I ws probably the first to watchw your video. Very clear and very useful. Thank you ☺️
Price please
@@kavirajpradhan5745 price range of 10j is 28k to 32k pesos, depends on the seller or if they are on sale.
Sir paano nyo na open ung hex screw ng blade adjustment? Ginamitan ko n ng impact driver (makita 171) ung sa akin di lumuwag. :(
Sorry now ko lang nabasa. Hindi ko ginamitan, walang space, pero matigas talaga, Allen wrench yung sa bosch
Sorry now ko lang nabasa. Hindi ko ginamitan, walang space, pero matigas talaga, Allen wrench yung sa bosch
Sir pag nagadjust ng blade alignment sa miter slot ang likod lang ba na allen ang iloosen? Or pati sa front? Natry ko kasi iloosen ang likod pero parang di xa gumagalaw ang blade. Pwede po ba mavideo nyo po ang movement ng blade.
Try ko minsan pag nag check ulit ako ng alignment, pakita ko sayo.
Hi sir can you help me can you show me how set up the switch i mean the wires
Sure. What wire is that?
@@DonDIYProject the wires the supply power to the switch there is to speed connect are numbered 1 and 3 and the wire 2 color blue and brouwn which color goes to which number
@@A5566z2 oh, did your wire stripped?
In some countries, white is neutral. Red phase and green one is soil.
No this is not how to adjust the fence..
Then How would you adjust the fence?
@@DonDIYProject You have to use a sqaure with the fence and the miter slots. Using eys is not accurate.
@@iq0099 I get it, that's one way of setting up the fence, there are other ways too like what I did. I didn't use just my eye, I used a straight edge to perfect lined it up with the miter slot knowing that my blade is aligned with it. Some uses other jigs, but just used the easy way and I found it accurate. Thanks for your input my friend.
@@iq0099 and I also did the method that you've said, but the tip of the combination square is getting under the fence.
@@DonDIYProject Here you go ua-cam.com/video/Wr85XZISwJ8/v-deo.html