Hello Jhonrey, salamat din sa appreciation. Actually di ako taga artic pero isa ang artic sa manning ng company namin. I'm working at Owner's office. Feel free to leave your comments 🙂
Hello Aness, when the LCD is ON, the actual feed rate will be increased to 125%. Meaning additional 25% from the 100% actual feed rate when LCD is OFF. Actually, it is not based on the basic feed rate. The basic feed rate could be your actual feed rate if the min feed rate setting is lower. The actual feed rate has a calculation and it has also a rule of which ever is higher with the min feed rate. Also depending on where you have made the setting, wether on the feed rate adjust factor or on the running In. Should you have any clarification, feel free to leave your comment.
Hello Elmir, good afternoon too. Anong ibig mong sabihin, sa Lube oil feed rate ba, tungkol ba sa LO purifier? Kasi kung sa ME system oil, walang design feed rate kundi pressure lang. Pero kung ang ibig mong sabihin ay sa LO purifier, there is no such certain percentage of feed rate, the lower the better. Then keeping at recommended oil temp to lower the oil viscosity for better purification.
Hello Elton, for hitachi MAN B&W, right after the sea trial normally set na ng Maker ang feed rate factor to min of 0.40 as per owners request. Pero actually may calculation sya kung bakit at pano. Sa Mitsui MAN B&W initially ang feed rate factor ay depende sa Cylinder oil na gamit, either BN40, BN70 or BN100. May mga vessel na sa makers manual sa cylinder oil reduction period ay wala sa table ang BN70, normally ay BN40 at BN100. Therefore yong reduction period ng feed rate factor ay kailangan calculate. Ex: 40/70x100=0.57 at 0-100Hrs. Then gradually the feed rate factor is being adjusted depending on the RH, but take note that reduction of feed rate should only be done after confirming the satisfactory condition of your cylinder. Makikita mo din sa manual same wordings.🙂 Kung meron pang di malinaw, feel free to comment.🙂
Hello Chief, sorry ngaun ko lng nasagot tanong mo, akala ko nasagot ko na last time. Upon reviewing, walang reply. Actually if your lubricator is ACC, load dependent sya, automatically adjusting based on the basic feed rate, min feed rate and feed rate adjust factor. Kung ang LCD ay naka ON, ang magiging actual feed rate mo at magiging 125%
Chief Good day. ask ko lang po pag mag running po bago ang piston rings .pag mag running in inaadjust din yong sa Running sa baba o sa Feds rate factor adjustment lang ang inaadjust po. salamat sa advise God bless. Safe sailing everyone
Hello RSZ, salamat sa tanong mo. actually sa manual ng Mitsui MAN B&W nakalagay na ang adjustment after overhaul ay sa Running IN, while sa cylinder feed rate reduction feed rate guidance, naka lagay na Running IN should be OFF forever. While sa Hitachi ay iba din naman. According to the Maker, either way ay pwede, pwedeng sa Feed rate adjust factor or sa running IN. In our company, our practice is sa Feed rate adjust factor which is okay naman sa engine maker/Engrs where in frequently we are having training with them. Kung sa Running In ka mag adjust, what ever your setting for that cylinder will be your actual feed rate while kung sa Feed rate adjust factor, your actual feed rate will be Feed rate adjust factor x nominal/basic feed rate. I would rather suggest to adjust sa Feed rate adjust factor.🙂
Somebody ask kung ang LCD daw ba ay automatic. Actually it will auto ON upon starting and when you increase nor decrease the engine RPM. After about 30 mins on steady RPM, it will auto OFF.
Hello dipankar, thank you for the comment, i will take it for the coming videos. Please let me know which particular video do you want, I will try to make an english version.
Hello Mike, sorry for the late reply. Actually the heating of cylinder oil is depends on the design. Merong design na ang gamit at electric heater at meron din namang na gamit ang ME jacket cooling as heating agent. Parehong may thermostat so you can set the temp.
Hello Chard, actually pwede din naman, however it overrides yong calculation ng actual feed rate. Kung anong setting mo kasi sa Running In, yon din ang actual feed rate mo regardless kung magpalit ka ng sulfur content. Siguro kung iisang klaseng fuel lng ang gamit nyo till reaching the 500 hrs after overhaul ay pwede din naman, pero kung kung mag iba kau ng fuel lalo na kung higher sulfur, then might be your setting ay kulang. We would rather suggest to make the adjustment sa feed rate adjust factor.
@@marinerealtalk8683 thnx ulit sir..malinaw na sa kin sir..lagi naman gamit namin VLSFO below 0.5 sulfur content..ngayon di na ko kabahan..malqking tulong sa ting mga marino mga videos mo sir.
Hello Ruel, VLSFO ba o LSMGO? Kung VLSFO, enter mo lang ang sulfur content sa MOP and it will automatically calculate para sa basic or nominal feedrate. If ever mas mababa sya sa min feed rate, your basic feed rate or nominal feed rate will be the min feed rate. But take note, if VLSFO, normally is using different grade of Cylinder oil. Pero meron ding cylinder oil na applicable even sa HSFO and VLSFO. If sa LSMGO, actually same din pero kung about 24hr or less lng naman ang consumption, pwede na ding wag mo ng palitan setting.
Sir, I have a question. When the ship's engine is using VLSFO(sulphur content is less than 0.5%), still would it be better to use TBN70 Cylinder oil but decrease the feed rate than using HSFO? Or using TBN40 cylinder oil would be better? Cause, I know that TBN(CaCO3) is also used for removing carbon sludges from fuel oil and other functions(Of course, I also know that if there are too much CaCO3, the sludge from itself would harm the piston and cylinder liner). So sometimes I still have questions to myself that would it be better to use TBN70?
Hello, thank you for the interest on this matter. Actually you are right that higher BN is more effective in cleaning purposes having a higher cleaning ability. On the other hand, the lubricant's BN measures its ability to neutralize acidic products of combustion, which are caused by the sulfur in the fuel. It is therefore, the higher sulfur content of the fuel, is recommended to use a higher BN. Using oil with too high BN could lead to deposits on the engine combustion components that can cause wear or scuffing. Due to issue of cleaning and acid neutralization. Some oil companies has now the type of oil that is applicable for HSFO and even for VLSFO, no need to change.🙂
Yes there is, actually some of our vessel are using it but supply is limited, only here in Japan. You are welcome, feel free to raise question to any of my videos.
Hello Joel, sorry late reply. Pwedeng mahingi ang buong alarm code. Kindly confirm kung fluctuating ba ang hydraulic pressure mo , bumaba or tumaas than normal. Was there any other related alarms?
Hello Joel, as per alarm code your ME is ME-B tama ba? Kung ME-B nga makina nyo, yong alarm code na binigay mo ay hindi connected sa hydraulic pressure. One more thing as per your info, it only alarm on ccu3. Try to change the MPC of ccu3
Hello Joeffrey, yes tama ka. Kung ang calculated basic feed rate ay mas mababa sa Min Feed Rate Setting, and magiging basic feed rate mo ay same as Min Feed Rate dahil sa "which ever is higher between the calculated Basic Feed Rate and the Min Feed Rate".
@marinerealtalk8683 sir puwede po ba pag running in ng isang cylinder para Di mag auto calculate ng actual feed rate direct na ako sa running in bottom dun ko na po nilalagay yung running in feed rate according sa running in feed rate graph ng makina. Puwede po ba na option yun po. Maraming salamaat po.
Hello Jeoffrey, if I'm not mistaken para ito sa bagong overhaul mong cylinder. Actually pag sa running IN ka nag input, it override yong calculation na feedrate adjust factor x basic feed rate. What ever input mo sa running In will the the same sa magiging actual feed rate ng cylinder na yon. Though in the manual mababasa natin na sa running In mag adjust pag nag overhaul, you can alo reconfirm on the cylinder oil reduction guide kung may naka sulat na Running In should be OFF forever. If ever meron, then your adjustment sa bagong over haul mo ay sa feed rate adjust factor instead sa running IN.
Hi sir..Makita Mitsui ang engjne namin pag nag overhaul kami ng piston palit ang piston rings..nakagawuan na namin don kami sa Running In kami nag aadjust..hanggang matapos ang Running In Period sa awa ng diyos okey naman ang mga piston rings during inspection.
Hello Chard, actually, ok din naman sa running IN, steady ang feed rate mo kahit na mag bago ka ng sulfur content. However, kung galing ka ng medyo mababang sulfur then will use a higher sulfur, normally it requires a bit more feed rate (actual feed rate) at yon ay auto calculated if sa feed rate adjust factor ka nag set. Remember, even the Maker says that the reduction period written in the manual is just a guide and it doest mean to presicely follow. The adjustment/reduction should be after confirming the satisfactory condition of your cylinder.
Hello Sir, actually it has but if your ME is fitted with load dependent lubricators, it automatically feed based on the setting depending on the engine load. While for engine fitted with mechanical lubricators, we just normally set or adjust to increase the feed rate at manuevering load/RPM.
@@marinerealtalk8683 Hitz Man B&W 6S46MC-C7 Fuel use is VLSFO 0.5%sulfur Actual setting in alpha lub is 1.3 g/kwh in all cylinder Newly overhaul cyl no.2. What will be our running in settings for cyl lubricator sir?
Hello Hilgardo, sorry for the late reply. So ang ME nyo pala is MC-C and using VLSFO. Actually, when VLSFO has stated to use, there was no certain calculation para sa feed rate kasi dipa alam ang effect sa makina kaya nag increase tau ng about 1.3 from normal na 1.0gkw/h. Then depending on the actual observation, maker's advice na pwede nating reduce providing with satisfactory condition ang cylinder particularly the liner. In case newly overhauled piston, increase to 150% then gradually decrease till reaching the normal or minimum feed rate upon reaching 500HR. But according to manual, reduction of feed rate should only after confirming the satisfactory condition of the cylinder. So very important ng inspection. In the case of long voyage and inspection will not be feasible, I would recommend to just gradually decrease in an interval of every 48hrs, same instruction I normally given to our managed vessels.
@@marinerealtalk8683 hello po sir. Salamat po sa pag sagot. Ang maximum po namin na feed rate sa system hanggang 1.7 lang po sir. Wala na po itong itataas pa. Kung sa 1.0 ako mag babase. 1.0 + 150% = 2.5 So sagad ko na lang sa 1.7 g/kwh sir, kasi hanggang doon lang ang settings na pwede ma adjust. Salamat po ulit sir and more power. God bless you
Nice info sir. God bless
Hello Garmie, thank you for the appreciation🙂
Good
Congratilations Sir. ✅👍
Thank you Ms. Lany🙂
Salamat sa shared ideas Sir’ sundan namin iba pang kabanata’
Welcome Engr. Nic at salamat din sa appreciation 🙂
@@marinerealtalk8683 welcome po Sir, subaybayan po namin ‘
Salamat sa pag grant ng request ko sir. It helps a lot
Welcome Chief Roy🙂
Keep going very helpful lodi 👌
Thank you Sir🙂
Please make video in english for all.thanks
Thanks for the interest Sir Kadam, I will try to put a subtitle.
Thank you sir.gbu..
You're welcome Sir Mack🙂 feel free if you have any comments. Thank you.
Good day po sir sa Arctic din ka po pala sir hehehehe :) thanks po sa pag share dinowload ko talaga yung vids na to 😊
Hello Jhonrey, salamat din sa appreciation. Actually di ako taga artic pero isa ang artic sa manning ng company namin. I'm working at Owner's office. Feel free to leave your comments 🙂
When LCD on actual feed rate is increased to 25 percent of basic feed rate. Not 125 percent.
Hello Aness, when the LCD is ON, the actual feed rate will be increased to 125%. Meaning additional 25% from the 100% actual feed rate when LCD is OFF.
Actually, it is not based on the basic feed rate. The basic feed rate could be your actual feed rate if the min feed rate setting is lower.
The actual feed rate has a calculation and it has also a rule of which ever is higher with the min feed rate.
Also depending on where you have made the setting, wether on the feed rate adjust factor or on the running In. Should you have any clarification, feel free to leave your comment.
👍👍👍
Thanks
Good job sir
Hello Sir Pooja, thank you for the appreciation. If you have any comments or question to any of my videos, feel free to ask.
Thank you sir, it helps a lot.😊
To God be the glory Chief Loreto🙂
Thank you sir for this imfo...
Welcome Chief Antonio and also thank you for the appreciation🙂
@@marinerealtalk8683 Iam always follow to your vlogg..
Thank you Chief.🙂
Sir baka pwede naman po sa alpha lub system na feed rate adjustment.
Sir good adternoon paano naman sa lubeoil feed rate .? Salamat po mabuhay kayu God blees as all
Hello Elmir, good afternoon too. Anong ibig mong sabihin, sa Lube oil feed rate ba, tungkol ba sa LO purifier? Kasi kung sa ME system oil, walang design feed rate kundi pressure lang. Pero kung ang ibig mong sabihin ay sa LO purifier, there is no such certain percentage of feed rate, the lower the better. Then keeping at recommended oil temp to lower the oil viscosity for better purification.
@@marinerealtalk8683I think he means.... How you got the feed rate factor of 0.4 ?
Hello Elton, for hitachi MAN B&W, right after the sea trial normally set na ng Maker ang feed rate factor to min of 0.40 as per owners request. Pero actually may calculation sya kung bakit at pano. Sa Mitsui MAN B&W initially ang feed rate factor ay depende sa Cylinder oil na gamit, either BN40, BN70 or BN100. May mga vessel na sa makers manual sa cylinder oil reduction period ay wala sa table ang BN70, normally ay BN40 at BN100. Therefore yong reduction period ng feed rate factor ay kailangan calculate. Ex: 40/70x100=0.57 at 0-100Hrs. Then gradually the feed rate factor is being adjusted depending on the RH, but take note that reduction of feed rate should only be done after confirming the satisfactory condition of your cylinder. Makikita mo din sa manual same wordings.🙂 Kung meron pang di malinaw, feel free to comment.🙂
Ask kolang idol how to know the main engine cylinder oil feed rate load in %
Hello Chief, sorry ngaun ko lng nasagot tanong mo, akala ko nasagot ko na last time. Upon reviewing, walang reply.
Actually if your lubricator is ACC, load dependent sya, automatically adjusting based on the basic feed rate, min feed rate and feed rate adjust factor. Kung ang LCD ay naka ON, ang magiging actual feed rate mo at magiging 125%
Chief Good day. ask ko lang po pag mag running po bago ang piston rings .pag mag running in inaadjust din yong sa Running sa baba o sa Feds rate factor adjustment lang ang inaadjust po. salamat sa advise God bless. Safe sailing everyone
Hello RSZ, salamat sa tanong mo. actually sa manual ng Mitsui MAN B&W nakalagay na ang adjustment after overhaul ay sa Running IN, while sa cylinder feed rate reduction feed rate guidance, naka lagay na Running IN should be OFF forever. While sa Hitachi ay iba din naman. According to the Maker, either way ay pwede, pwedeng sa Feed rate adjust factor or sa running IN. In our company, our practice is sa Feed rate adjust factor which is okay naman sa engine maker/Engrs where in frequently we are having training with them. Kung sa Running In ka mag adjust, what ever your setting for that cylinder will be your actual feed rate while kung sa Feed rate adjust factor, your actual feed rate will be Feed rate adjust factor x nominal/basic feed rate. I would rather suggest to adjust sa Feed rate adjust factor.🙂
🖒🖒🖒
Somebody ask kung ang LCD daw ba ay automatic. Actually it will auto ON upon starting and when you increase nor decrease the engine RPM. After about 30 mins on steady RPM, it will auto OFF.
kindly speak in english in your videos so that your video can be understood by all the people in the world. its a request
Hello dipankar, thank you for the comment, i will take it for the coming videos. Please let me know which particular video do you want, I will try to make an english version.
Automatic na po ba yan mag adjust yung temperature ng cyl.oil sa ganyang type na lubricator? Thank you!
Hello Mike, sorry for the late reply.
Actually the heating of cylinder oil is depends on the design. Merong design na ang gamit at electric heater at meron din namang na gamit ang ME jacket cooling as heating agent. Parehong may thermostat so you can set the temp.
Sir pwede ba mag adjust din sa running in..pag nagpalit ng piston rings..ginawa kasi yan ng CE namin.
Hello Chard, actually pwede din naman, however it overrides yong calculation ng actual feed rate. Kung anong setting mo kasi sa Running In, yon din ang actual feed rate mo regardless kung magpalit ka ng sulfur content. Siguro kung iisang klaseng fuel lng ang gamit nyo till reaching the 500 hrs after overhaul ay pwede din naman, pero kung kung mag iba kau ng fuel lalo na kung higher sulfur, then might be your setting ay kulang. We would rather suggest to make the adjustment sa feed rate adjust factor.
@@marinerealtalk8683 thnx ulit sir..malinaw na sa kin sir..lagi naman gamit namin VLSFO below 0.5 sulfur content..ngayon di na ko kabahan..malqking tulong sa ting mga marino mga videos mo sir.
Hello Chard, you are very much welcome. Kung meron kang iba pang tanong, just drop your comment sa comment section ng mga video ko sa channel na ito.🙂
Pls, kindly make the videos in English
Hello Faisal, I will consider your request, just me time.🙂
Sir, paano PG nka low sulphur Po Tayo sir?
Hello Ruel, VLSFO ba o LSMGO? Kung VLSFO, enter mo lang ang sulfur content sa MOP and it will automatically calculate para sa basic or nominal feedrate. If ever mas mababa sya sa min feed rate, your basic feed rate or nominal feed rate will be the min feed rate. But take note, if VLSFO, normally is using different grade of Cylinder oil. Pero meron ding cylinder oil na applicable even sa HSFO and VLSFO. If sa LSMGO, actually same din pero kung about 24hr or less lng naman ang consumption, pwede na ding wag mo ng palitan setting.
Now malinaw na po kaya pala minsan magtaka bakit mas mataas po sa minimum na 1.50g/kWh meron pala 125% whichever is higher than minimum feed rate’..
Yes Engr. Nic, be guided with this video.🙂
Sir, I have a question. When the ship's engine is using VLSFO(sulphur content is less than 0.5%), still would it be better to use TBN70 Cylinder oil but decrease the feed rate than using HSFO? Or using TBN40 cylinder oil would be better? Cause, I know that TBN(CaCO3) is also used for removing carbon sludges from fuel oil and other functions(Of course, I also know that if there are too much CaCO3, the sludge from itself would harm the piston and cylinder liner). So sometimes I still have questions to myself that would it be better to use TBN70?
Hello, thank you for the interest on this matter. Actually you are right that higher BN is more effective in cleaning purposes having a higher cleaning ability. On the other hand, the lubricant's BN measures its ability to neutralize acidic products of combustion, which are caused by the sulfur in the fuel. It is therefore, the higher sulfur content of the fuel, is recommended to use a higher BN.
Using oil with too high BN could lead to deposits on the engine combustion components that can cause wear or scuffing. Due to issue of cleaning and acid neutralization. Some oil companies has now the type of oil that is applicable for HSFO and even for VLSFO, no need to change.🙂
@marinerealtalk8683 Oh~~~ I didn't know that some oil companies have the cylinder oil for both HSFO and VLSFO. Thanks for reply
Yes there is, actually some of our vessel are using it but supply is limited, only here in Japan.
You are welcome, feel free to raise question to any of my videos.
Sir.. lagi mg alarm ang MOP hydr press Regulator high fail.. alarm id 0347.. sana matulongan mo ako sir
Hello Joel, sorry late reply. Pwedeng mahingi ang buong alarm code. Kindly confirm kung fluctuating ba ang hydraulic pressure mo , bumaba or tumaas than normal. Was there any other related alarms?
@@marinerealtalk8683 minsan mataas cya sa set point ang alarm hydr press regulator at ccu3_0070611
Hello Joel, as per alarm code your ME is ME-B tama ba? Kung ME-B nga makina nyo, yong alarm code na binigay mo ay hindi connected sa hydraulic pressure. One more thing as per your info, it only alarm on ccu3. Try to change the MPC of ccu3
Sir paano po halos lahat ng sulphur ngayon is less than 0.5 na po. Kaya yung nasusunod na lagi yung naka enter na minimum feed rate tama po ba sir.?
Hello Joeffrey, yes tama ka. Kung ang calculated basic feed rate ay mas mababa sa Min Feed Rate Setting, and magiging basic feed rate mo ay same as Min Feed Rate dahil sa "which ever is higher between the calculated Basic Feed Rate and the Min Feed Rate".
@marinerealtalk8683 sir puwede po ba pag running in ng isang cylinder para Di mag auto calculate ng actual feed rate direct na ako sa running in bottom dun ko na po nilalagay yung running in feed rate according sa running in feed rate graph ng makina. Puwede po ba na option yun po. Maraming salamaat po.
Hello Jeoffrey, if I'm not mistaken para ito sa bagong overhaul mong cylinder. Actually pag sa running IN ka nag input, it override yong calculation na feedrate adjust factor x basic feed rate. What ever input mo sa running In will the the same sa magiging actual feed rate ng cylinder na yon. Though in the manual mababasa natin na sa running In mag adjust pag nag overhaul, you can alo reconfirm on the cylinder oil reduction guide kung may naka sulat na Running In should be OFF forever. If ever meron, then your adjustment sa bagong over haul mo ay sa feed rate adjust factor instead sa running IN.
Hi sir..Makita Mitsui ang engjne namin pag nag overhaul kami ng piston palit ang piston rings..nakagawuan na namin don kami sa Running In kami nag aadjust..hanggang matapos ang Running In Period sa awa ng diyos okey naman ang mga piston rings during inspection.
Hello Chard, actually, ok din naman sa running IN, steady ang feed rate mo kahit na mag bago ka ng sulfur content. However, kung galing ka ng medyo mababang sulfur then will use a higher sulfur, normally it requires a bit more feed rate (actual feed rate) at yon ay auto calculated if sa feed rate adjust factor ka nag set. Remember, even the Maker says that the reduction period written in the manual is just a guide and it doest mean to presicely follow. The adjustment/reduction should be after confirming the satisfactory condition of your cylinder.
Thanks
Likewise, thank you for watching this channel. Feel free if you have any question🙂
Ask kolang idol how to know the main engine cylinder oil feed rate load in %
Hello Sir, actually it has but if your ME is fitted with load dependent lubricators, it automatically feed based on the setting depending on the engine load. While for engine fitted with mechanical lubricators, we just normally set or adjust to increase the feed rate at manuevering load/RPM.
Sir baka pwede naman po sa alpha lub system na feed rate adjustment.
Hello, pwede ba malaman anong specs/type ng main engine nyo. Para mas clear bigay ko sayong advice.
@@marinerealtalk8683 Hitz Man B&W 6S46MC-C7
Fuel use is VLSFO 0.5%sulfur
Actual setting in alpha lub is 1.3 g/kwh in all cylinder
Newly overhaul cyl no.2. What will be our running in settings for cyl lubricator sir?
@@marinerealtalk8683 maraming salamat po sir. God bless you po
Hello Hilgardo, sorry for the late reply. So ang ME nyo pala is MC-C and using VLSFO. Actually, when VLSFO has stated to use, there was no certain calculation para sa feed rate kasi dipa alam ang effect sa makina kaya nag increase tau ng about 1.3 from normal na 1.0gkw/h. Then depending on the actual observation, maker's advice na pwede nating reduce providing with satisfactory condition ang cylinder particularly the liner.
In case newly overhauled piston, increase to 150% then gradually decrease till reaching the normal or minimum feed rate upon reaching 500HR. But according to manual, reduction of feed rate should only after confirming the satisfactory condition of the cylinder. So very important ng inspection. In the case of long voyage and inspection will not be feasible, I would recommend to just gradually decrease in an interval of every 48hrs, same instruction I normally given to our managed vessels.
@@marinerealtalk8683 hello po sir. Salamat po sa pag sagot.
Ang maximum po namin na feed rate sa system hanggang 1.7 lang po sir. Wala na po itong itataas pa. Kung sa 1.0 ako mag babase. 1.0 + 150% = 2.5
So sagad ko na lang sa 1.7 g/kwh sir, kasi hanggang doon lang ang settings na pwede ma adjust.
Salamat po ulit sir and more power. God bless you