What you see when you apply a tapping bit to woodworking
Вставка
- Опубліковано 19 лип 2021
- #woodworking #woodworkingdiy #tapping
In this video, I made a screw tap in wood using a metal tapping bit.
The type of tapping bit used for the work is
1. Manual hand tapping bit
2.Tapping bits after drilling
3. A bit that can be tapped at the same time as perforation
The most important part of tapping, a few tips, and a cross-section shot of the inside that cannot be seen with the naked eye during work were edited in a three-dimensional sense.
Thank you. - Навчання та стиль
Excellent video tutorials. Love you taking the time to cut cross-sections to demonstrate what is happening inside the wood; it makes it much easier to understand what's going on!
Thank you 💚😊 Have a nice day 🍀😄
I still not get it, it looks all same to me, except that one witch drill and make shorter screw fit...
That was a great demonstration, and surprisingly strong!👌🏽
Cheers mate, appreciate your efforts of sharing this information.👍🏽
Thank you my friend 🤜🤛
Have a good timw 🍀😄👍
Well done !
Thank you so much Bro!!! 🍀👍😄👌
Gracias felicitaciones y siempre adelante
Muchas gracias. qué tengas un lindo día 🤜🤛🍀😄👍
교본 하나 만드셔도 되겠네요👍😁😊😄😃
저도 그 비트 샀는데 아직 쓸일이 없네요^^
더운데 건강 챙기시면서 안전목공하세요~
교본은요…. ☺️
저도 쓸 일이 없어서 영상이라도 만들어보자 하고 사용해봤습니다. 😄
좋은 주말되세요~~🍀👍👌🙋♂️
Cross-sections are great
Thank you 😊 Have a nice time 🍀
Awesome presentation
Thank you so much 😄
Always have a good time 🤜🤛👍🍀
Ótimo vídeo amigo parabéns 👏👏.
Obrigado amigo. 😄🙋♂️
Desejo-te sorte hoje🍀🍀🍀👍
지금 까지 탭은 철이었는데 나무에 탭을 내다니 나무는 생각도 안했는데 새롭네요
잘보고 갑니다
다음 영상도 기대해 볼께요
감사합니다. 다다음 영상은 나무에 탭 비트없이 탭을 만들어보겠습니다. 🍀😄👍👌
궁금했는데 잘됬네요.^^
조금이라도 도움이 되셨다니… 부끄럽기도 하고 감사합니다. 더운 여름 건강 잘 창기세요. ☺️😄👍🍀
Très bonne vidéo et très instructifs
Merci. 🤜🤛👌👍
passe une bonne journée 😄🍀
Sympa ta chaîne UA-cam elle doit être suivi dans le monde entier vu que les sous-titrage sont assez bien fait et que tu as une bonne façon d'expliquer sans parler
Merci. passe une bonne journée 😄🍀
Video hay quá 👍
cảm ơn. 🇻🇳👍💚😄 Chúc một ngày tốt lành 🍀
Very good
Thank you 😄
Have a nice day 🍀👍🤜🤛
Needs in dynamometric test of thread and how many cycles screwing
Wow que hermosa herramienta
Gracias 😊 Que tengas un buen día 👍🍀👌
I think ill have to try this
Try it 👍👍👍👍👍
Thank you 😊 Have a nice day 🍀
Boa demonstrações, das brocas com machos e dos machos também, obrigado.
Obrigado 🍀😄👍💚
Amazing skills
Thank you 😄😄😄
Have a nice day 🍀🍀🍀
나무탭핑을 내면 나사를 철물로 해도 되나요? 수축팽창률이 달라서 문제 생기지 않는지요
네 개인적으로는 금속으로 된 볼트를 사용해도 무난한데 수축 팽창에 민감한 용도로 사용시에는 외국에서는 CA 본드를 나사선에 발라주고 사용한다고 합니다. 좋은 하루되세요 😄
SUPER DUPER ❤️❤️❤️
Thank you 🍀💚😊 Have a nice day 🍀
Надо ещё сделать видео
Как нарезать резьбу в картоне
Спасибо 😊 Хорошего дня 🍀
А меньшим диаметром такие сверла есть? Например 2,8 или 3, 2 мм?
Да, у меня самая маленькая насадка, 3,0-3,2 мм. Я еще не видел меньших кусочков, но, вероятно, они есть.
Спасибо 😊 Хорошего дня 🍀
High skill
Thank you 😄
Have a nice day 🍀👍👌
I wonder the shear and pull strength for small to mid level projects
A someone mentioned glue! This is amazing. Thanks
Have a nice day 🍀🍀🍀😄👌
Shear strength is generally determined by the fastener, within reason. Pull out can be increased with a fender washer/nut, if necessary.
Ce que vous présentez le perçage et taraudage
Sur bois
Est-ce que c'est faisable sur aciers
I need this
Thank you 😊 Have a nice day 🍀
나무에 탭이라 신선한데요^^
요즘 왜이리 더운지… 손바닥도 아픕니다. 낼은 올만에 휴가나 즐기까 합니다. 목손님도 더운 여름 건강 잘 챙기십시요. 🍀👍😄🙋♂️
If you soak the treads with CA glue, they will be a lot stronger.
CA glue…. Thank you for good information. Have a nice day 🍀😄👍👌
👍👍👍👍
Thank you 😄
Have a good day 🍀👍🤜🤛👌
nice..... compare some drill bits.
Thank you 😄
Have a nice day 🍀👍
@@BStarCrafts your demonstration other tapcdrill... is useful, thank you.
🤜🤛👍
영상에 나오는 비트 구입처 부탁드립니다~^^
네이버 검색창에 스파이럴탭 치면 수코리아랑 메가툴 두 곳에서 구입한 걸로 기억합니다. 해치피 주말 되세요 😄🍀
👍👍🤝
🤛🤜👍🍀👌
I always oil the wood with BLO if by hand
Hahaha! Thank you Bro….👍
I only thought of the oil, but I didn't use it to work. When I made the next video, I told Softwood to try it out... Thanks for the very good advice! wish you a happy day😄😄😄😄🙋♂️🤜🤛👌🍀
@@BStarCrafts no advice to give you : you are exceptional of talent . I struggle making simple scarf joint in pine :( I do everything by hand and my pine is so dry that it chips everywhere. Very discouraging.
It's an undeserved compliment for me, and you're very humble. Always work safely ☺️
You should put some Cyanoacrilate (instant glue) into the threads to get the wood fibers stronger. Do this two times: just after cutting, and then run the tap again by hand, and repeat the glue application.
Lastly, add a little hard wax coat, thus ther glue hardened and waxed threads will be much stronger and will not be easily worn by repeated screw tightening and untightening.
Aeromodelers use that technique on Balsa wood threads, because balsa is too soft, but the Cyano glue helps a lot in any wood too.
Thank you 😊 Have a nice day 🍀
👍 👍 👍,
Спасибо 😊😊 Хорошего дня 👍🍀👌
기계전공이라 목공에 문회안입니다. 목공영상보며 항상 궁금했던 한가지 여쭤봅니다.
목공에도 치공구만들때는 플라스틱을 부분적으로 사용하면 어떨까요?
너무 비용이 많이 들려나~?
부분적으로 사용하면 가격도 낮추고 내구성은 크게 향상될것 같습니다.
(특히 슬라이딩 부위)
예)MC나일론, ABS, 테프론,아크릴 등등
네 나무의 특성상 수축과 팽창을 반복하기 때문에 플라스틱 레진 종류를 사용하면 내구성 면에서 훨씬 좋을 것입니다. 그런데 보편적으로 이용되지 않은 이유는 개인 작업실에서 플라스틱을 사용하면 가공 및 접착 등 가성비 문제가 있지 않나 개인적으로 생각합니다. 좋은 의견 감사합니다.
좋은 주말되세요 😊💚🍀🎁
drill & tapping a plastic tube insert works well too as not much tare out ,as its solid not fibrous like the wood & you pick the colours & cheaper than steel inserts even if it takes a little more time ^_~
Thanks for the nice comment and have a nice day 👍😄🍀🤜🤛
Or a D Nut. Not as aesthetically pleasing but definitely way stronger than tapping the wood itself
What kind of tree?
Rubber tree…
Thank you 😊 Have a nice day 🍀
Como se llama ese kit de la maleta azul??
Una herramienta manual para hacer hilos.
A hand tool for making threads. 😊
You can fill the hole with super glue and make it spread through the threads and soak in the wood surface. When it hardens, it will make the threads more durable.
Good 👍
Thank you 😊 Have a nice time 🍀
👌👍😎.
🤜🤛👍🍀😄
Разные породы древесины
Over the years I've tapped wood, plastic, nylon and even rubber. The more threads you can cut the better the grip of the screw. The principle is always the same. My favorite choice is 1/4" x 20. If you don't ever want it to come apart add some super glue to the screw before assembly.
My favorite trick is to use a flat piece of automobile plastic to replace stripped/missing blind body panel fasteners. Cut the piece, thread it and glue it behind where the missing fastener is supposed to be. Run the screw into the new piece just like the original fastener. If it's one of several on the bottom of the car/truck you can't tell the difference.
Thank you 😊 Have a nice day 🍀
At times visuals only leave something to be desired. A simple voice over would have been helpful in parsing the details.
Hi~ want to do it with my voice, but I can't speak only Korean... 😭
Thank you 😊 Have a nice day 🍀
Pine and hard wood is not the same!
👏👏👏👏👏👏👊🇧🇷👍💯
Thank you 👍😄
Have a good time 🍀💚
Tem uma luz
Obrigado 😊😊 Tenha um bom dia 🍀
A D nut is still a stronger choice though.
Right 👍
Thank you 😊 Have a nice day 🍀
用去木头上要更粗的牙！
甚至用方牙，因木质比较软，不经的拉……就没有牙了。
大孔的牙才有些力。
Se al posto della punta da 7 mm usassi wuella da 6.5 x M8 ssrebbe un pelo meglio
산안내고 그냥박어도 게안던데
那個我也買了，齒紋都是小一號（便宜沒好貨）
你好。 🙋♂️😄
你說得對。 便宜的也很難使用。 祝你今天過得愉快 😅
수동 탭핑.. 욕 나오던데.. ㅋㅋㅋ
ㅋㅋ 맞아요… 진짜 사용하는 경우는…
앞으로 거의 없을 겁니다. 😁
Krzywo jak
Buenas tardes yen Colombia a dónde se consiguen gracias
Где русские
Спасибо 😊 Хорошего дня 🍀
M
ау
Thank you 😊😊 Have a nice day 👍👍👍
@@BStarCrafts 감사 해요
Якщо руки криві їх не виправиш
Он пьяный что ли все отверстиязасверливает под углом