Hi Great vid. I have a normal key start generator and a smart controller MPPT150/100-TR. Could I link my generator to the controller using the V2 Autogen to automatically start my generator when my lithium batteries drop to the manufacturers low level recommendation?
We have used the ua-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
Very cool and I have cellular phone, android. But there is no grid in many places with internet so how can this connect unless it has a cell service subscribed in to the controller. Like those little security cameras, you must have cable or a mobile hot-spot which must be connected/activated for use. We know things dont just 'connect' to the internet without a sim card and subscription.
I think this is great product. I would love to see this product being assembled on the more common "inverter generators" of 1000 watts or 2000 watts size (that would be a selling point for me and I'm sure for a lot of people as well). As there are 3000 watts generator with remote switch already in the market but no remote controled smaller size generators. I searched everywhere for small generator with remote control but I didn't find any in the market except yours (some DIY videos in YT I have seen are too technical for my liking, also not as good of a solution, and I don't have time to go deep into electronics to solve this issue and do trial and error unfortunately, Im looking for an easy solution). I hope you make video demonstration of your product on 1000 or 2000 watts inverter generators. I have your channel on my notification list and your website on favorite but I'm hesitant to buy without demonstration video of this product on an inverter generator size 2000 watts or smaller. Such video will give us confidence on its exact configuration and operation step by step on inverter generators of the mensioned sizes. So no guess work needed or uncertainty.
Hello @Mansur. Our controllers can be fitted to any generator type or size. Although it must be equipped with an electric starter motor. If you are referring to small 1000watt inverter types with a pull rope start, then this(or any other product) will not be able to auto start the generator. It is not limited to Generators. The V2 AutoGen has also been fitted to petrol engine air compressors, petrol and diesel engine water pumps and other standalone engines. As long as it has a starter motor, the V2 AutoGen can auto start and stop the engine. With or without choke on petrol engines, fuel injected, LPG conversions or decompression levers on diesel engines. So rest assured, we have a solution! The V2 is also customisable according to the application. Can receive a trigger to auto start from an ATS on mains power loss, pressure switches, water level sensors, battery banks, solar charge controllers etc. The sky is the limit!
@@JM-yx1lm You do realise that what you are asking for is a small generator with No electric starter to have a remote start option? The reasons why small inverter type Generators are Small, is because the manufacturer needed to create a product that is lighter, smaller and more compact. They designed it without a starter motor and lead acid starter battery for those reasons.
How would this work in the middle of winter? My idea is to bolt a generator in the box of my pickup and run a cord to front so I can plug it in. Is it possible to come up with something that can program to run for 5 hrs then shut off?
Hi. It can be done, just need to protect the controller from the elements. It's not waterproof! Timer is easy, we already have that available as a feature.
Good day, I am in South Africa and this product is the best I have seen, but, is it available in South Africa? Also where is this APP available, as I checked on PlayStore and nothing?
Hello Mervin. We do ship worldwide. Sent many to South Africa so far. You may view and purchase our products at www.dcautogen.com Links to our AutoGen app are also available on our site. Keep in mind that the app can only be used with our products. There is a setup process when you install the controllers or generators as you need to scan the unique QR Code attached to device.
We have a pull start generator with an off switch, we use it to run a well on a lease property we have cattle on. It’s 30 miles one way from headquarters. We go down in the mornings Monday, Wednesday, Friday to feed and check cattle and to turn the generator on to fill up our overhead tank which feeds the water trough. After 8 hours we drive back down to turn the generator off. It’s not economical as you can imagine. Is there a way to put a timer off switch or a timer valve on the fuel line so that after 8-10 hours the generator will shut off?
Hello Travis, yes that is easily done with a 12v programmable digital timer. Set it for X amount of time to trigger. Some models have an onboard relay which will shutdown your generator. Fairly inexpensive. If your generator had an electric starter, then with an AutoGen controller, everything would have been automated to start and stop when needed.
we are interested in installing a 100 amp hr 12V lithium battery in our travel trailer. Our plan is to use a small inverter generator with command start to maintain the battery and power appliances. The priority power draws are a 12V dc fridge that requires approximately 600W per day and the blower on our propane furnace. Lighting is all LED. The battery should service this load overnight and it would be desirable to have the generator to auto start to maintain the battery while we are away from the trailer. Will the controller integrate with the generator's factory command start and also allow me to manually start the generator when we need to power larger appliances such as our AC? Most campgrounds also only allow generators to operate from 10am-6pm so there would also need to be a way to prevent the generator from auto starting during this timeframe in some instances. Sorry if this post showed up twice.
Hello Thomas. Whenever running a backup generator if grid is down, you must use an Automatic Transfer Switch. This disconnects your distribution panel from main grid and generator feeds your distribution panel.
Thanks for sharing. I have a MGC100 that i am trying to setup on my Champion 100110 but cannot figure out all the wiring yet. I have the crank (starter), b-, and b+ but cannot make sense of the other 3 wires needed. I currently made my own setup remotely in the garage to start the outdoor generator by duplicating the current onboard switch on the generator but want to use the MGC100 instead. Any thoughts? I think the EM Stop would be the one of the other three to stop the engine which leaves me with 2 remaining wires. The generator has a 6-pole combination switch that controls it all.
I have the MGC100 as well and couldnt get it to work. I switched to this and it works now. I think the MGC100 needs some relays added to it but the seller can't dumb the instructions down to my level. LOL
Hi, I have a wen 3750 dual fuel generator and want to connect it to Schneider electric AGS, the generator is just a key. Would this help me connect the generator to the AGS?
Hi. Looks pretty straightforward. If it has manual choke, you will also need our choke linear actuator. Check out the V6 AutoGen smart controller on our website www.dcautogen.com
Is there a controller like this to convert a portable electric start to a 2 wire standby startup? My solar controller accepts generator input and has a 2 wire signal to start the generator. But my portable doesn't have 2 wire compatibility.
What are you using for the choke circuit? Does that gen have some kinda electronic choke or did you rig up some solenoid to switch it on and off with the v2 signaling? Im going to have to design a circuit that will hold off the starting sequence for a few seconds while the "choke" presses on a propane priming button to fill the carb with propane in order to start.. no physical choking necessary, you just have to prime the system for 5 seconds then immediately hit the starter so the propane will continue to flow with vacuum. Which aitomatically shuts if the gen shuts off.. im guessing the 5v circuit on the v2 can be setup like this maybe or will i have to make a little timer circuit that will pop on if power goes out then tell the v2 to start sequence..??
Hi. You can use our Choke Servo or Choke Linear Actuator. Both available on our online store. Do you have an AutoGen controller already? Send us an email with your requests so we can guide you. Some programming may need to be done for your controller.
Could it be used with a well pressure switch so it could start the generator when the pressure falls to 50psi and then kill it when the pressure reaches 80psi?
Wonder if there is anyway to program this device to automatically start the generator if let’s say I was on my boat and we were running devices off the house/boat batteries and wanted the generator to only start when the voltage dropped to a certain level? Would be a cool feature, although I guess most folks would just be using the generator w devices plugged directly into the generator and would have it running the entire time.....
Hi CrazyMoFo. The V2 AutoGen controller already does that. It starts the generator when your battery bank falls below the user selected low battery voltage threshold within the app. You can view more details at www.dcautogen.com
There are a few ways to approach this. If your inverter/charger has a programmable dry contact relay, this can be programmed to send a start and stop signal to AutoGen according to battery bank state of charge. If this is not available, you would need to add our DC current sensor which will calculate when to shutdown the generator by observing the tail current drop during the Absorbtion stage of charging. When current falls below a preset value, AutoGen controller will shutdown the generator. It does not calculate state of charge though.
I want to buy one of these, but I would like to hook up a portable inverter generator to my off-grid solar system on my bus to supplement energy in the summer for an a/c unit on low setting if possible. Do you know where I can find information for setting up a backup generator to solar batteries? There seems to be no information on this.
Hello Zack. It is possible to install on an inverter generator. You may also find mppt solar charge controllers that accept input from an AC generator to charge your battery bank. You can visit our website for more information on our products at www.dcautogen.com
Hello. Yes, it is compatible, but you will also need our Choke servo to operate the servo during startup. Here is the link for your reference. dcautogen.com/product/v2-autogen-12v-controller/
@@DCAutogen Looking to buy one and I am trying to understand how the controller receives a hardwire start signal. We have a couple of rural WAN towers that we need backup on and I want to make sure this will work for us as opposed to buying a 7kw generac standby.
The V2 monitors a battery bank, if the voltage falls below a set threshold it will start the generator. Example: If you apply a 12v signal to the monitoring pin #10 and #12 via your relay, when the relay cuts the connections and no longer feeds 12v to those pins, the V2 will start your generator. When V2 receives 12v again on #10 and #12, it will kill the engine.
@@DCAutogen hi Nick. Love your videos mate. Bought a V2 AutoGen for my Honda EU is 3kw. Could you send me instructions on wiring to that. I got the choke servo too. My email is Jrcxley@gmail.com Cheers. John Crossley. P.S. I'm in The Gold Coast, Queensland.
The time and effort we spend with our clients pre and post sale for individual customization, by far surpasses the $300 price of our controller. Thanks ;)
Dude 300$ aint about shit when you look at about anything for a generator.. if you get a commercial stand alone is like 1-2 grand and has a bunch of features most people wont ever need to use or could use. If you go the auto start at the electric panel than by the time u get the transfer switch, breakers, sub feed to generator panel if not already but the transfer switch alone is pushing 300$.. I mean you probably own an iphone or samsung and spent close to a grand on it and its just a godamn phone..
Hello Jeff. The V2 AutoGen is an automatic generator start controller. If you don't need the use of the app for monitoring, or manually starting from a remote location, then don't use the app. You can just install it and forget it, let it do its thing :)
Can this be setup on a Kubota 2cyl diesel with 12 volt alternator. Alternator needs 12 volt, glow plug, starter, fuel shut off. Can a proximity sensor be used for crank rotation so controller knows if engine is running or not?
Do you have a video for your V6 using an ATS switch? For example,, the ATS has a 12 volt DC built in it and yet the Generator has the 12 volt Battary and we just purchased the Solar charge. We just can't find it.
Good day sir you said connect the three important wire 1st is the kill switch second is for starter relay and for the 3rd sir you didn’t mention it? What is the 3rd wire
Hi. It can take either of the 2 available user options within AutoGen app: Measured dc voltage of starter battery charging circuit or generator ac output.
@@DCAutogen if the physical lines for the internet are down you can’t get it even with power. A cell booster is best. Most cell towers have generators. Get a cell booster and drastically improve your cell service. It won’t be as fast as WiFi, but it’ll be possible
The V2 AutoGen is out of stock and no longer in production. It has been replaced by the V6 AutoGen smart controller available through our online store.
No, it doesn't need WiFi to operate. It needs a 12v power supply. Therefore, by powering via your starter battery, it will operate when you Power goes out.
Hi, I have a generator with a manual choke, purchased new 2 days ago. Still can't get passed my head how a manual choke can b operated digitally (aren't manual chokes off a cable), I want to also know could this unit be fitted to a compressor as well to remotely start it? Both are 12v both key start with a manual choke compressor is deisel and generator is petrol. Also can one of these handle the two unit or do I need one for ever unit? Do you have a place in Melbourne that can install?
Hello Morin. Servos or solenoids are needed to operate the manual choke. We provide a digital servo and bracket with our AutoGen controllers for this purpose. Visit our store dcautogen.com Yes, has been installed in the past on engine driven compressors. You need a controller on each engine unfortunately. We are not located in Melbourne, Australia anymore. But I can find someone for you to assist with installing if the need arises.
It can still operate without WiFi. All depends on how and when you want the generator to start and stop. Limitations of no WiFi is, no remote start or monitoring via AutoGen app.
Hello Eze. Ofcourse! The V2 AutoGen controller uses a digital servo to open and close the Choke during startup. Here is a link of our V2 AutoGen controller. dcautogen.com/product/v2-autogen-12v-controller/
That has been accounted for. The AutoGen controller will never engage the starter as it receives a running signal on one of its inputs. It always knows if it's running or not.
Hello J. It's compatible with any electric start generator. If your generator has a manual choke system, you will also need our choke servo. Depending on your generator wiring, you might need to use external 12v relays to complete the installation.
I'm sorry I'm quite confused. Is there an alternative for that? I am worried if internet is cut from a hurricane then I might not be able to gain access via wifi?
I feel like this won’t work when power goes out. If power turns off then your WiFi will also, cutting off the command between the module and your app... if you can prove me wrong, I’ll buy one.
Hello Jake. The controller still operates in Auto mode even without an Internet connection. It can be programmed to start if monitoring a battery bank, if utility power goes down, if on a timer etc. WiFi is needed only to monitor, remote start and to update any user settings. Is there something else you would like to ask?
No idea of this is still an active thread or not. I would like to run a predator 9500 inverter generator tied to a Sol Ark 15k, what's your thoughts on running the 2wire start out of the Sol Ark to run this controller?
I think I figured it out. Looking at your V6....using the ac inputs and a NC relay, snagging a power source (have to figure out what the 2 wire circuit on Sol Ark requires) for the coil side....run any ac power to the contact sides of the relay then to your controller on the AC input. When the Sol Ark calls for generator, it would close its relay completing the circuit, activating the relay coil, opening the contacts on the relay. Your controller would see that break, then know to start up the generator. When the Sol Ark is satisfied....it opens its relay turning the relay back to NC....your controller now has AC...then knows to stop the gen set. If you see another way....or have a controller actually set up to support a 2 wire start from inverter...let me know, please.
Hi Wade. The AC inputs L and N are used as a generator running signal. For 2 wire start function we use pin#12. Whenever this input senses +12vdc it will trigger an autostart and 0v will shutdown.
sol ark has starter delay . you don't need no $$$$ controller . you can get away with 3 NC relay relays( they like $15 for 3 pack on amazon). its what I did for my sol ark with predator inverter. tested and works great
The V2 connects to starter motor relay for starting. It also connects to fuel relay or coil to kill the engine. Communication between V2 and mobile app is over the internet. V2 connects via wifi. To find more info on the V2 AutoGen please visit us at www.dcautogen.com
@@rahuldogra If you only require a signal to be sent to the AMF to switch on or off, then yes it can be done via our app. Do you need to operate the generator remotely? If you also only need signals sent to the Koels panel for remote start and stop, this cam also be done.
Hello danjjr. Yes, I believe there is a manual choke on that model, so you will need the choke servo with a V2 AutoGen 12v controller. Is it equipped with any safety cut off solenoids for the LPG?
@@DCAutogen Okay, thanks. Yes, the safety cut off is an additional accessory and I'm thinking about buying it: www.wincogen.com/product/low-pressure-fuel-solenoid/
Should have been added as a standard option in my opinion. Either way, the V2 AutoGen can be fitted easily. You may find our products here. www.dcautogen.com
Some essential things can always be powered by a backup system. UPS can provide power to small loads. Some modems/routers can be powered by 12v. There is always a solution...
Hello Leo. Yes it has a daily timer which you can set to start and stop. Also has run timers after the generator has started. All these can be set via AutoGen app.
Hello Dan. The app and controller need an internet connection to operate or monitor the generator from any location. Their is no other way unfortunately. But the AutoGen can still operate in Auto Mode without internet. It will monitor battery bank level or loss of grid power and start the generator. Hope this helps.
Hi Nick I'm trying to contact you but don't know how to get your email address. I'd like to know what parts are used and where to purchase everything. Thank you for your time and I look forward to your response.
Hi
Great vid. I have a normal key start generator and a smart controller MPPT150/100-TR. Could I link my generator to the controller using the V2 Autogen to automatically start my generator when my lithium batteries drop to the manufacturers low level recommendation?
Hi Pumpkin Eater. You surely can! Most importantly is also knowing when to stop the generator and the Victron can send the signal to the V2 for that.
We have used the ua-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
hI ALEXANDER NICE VIDEO. Question what generator do you have there. it seems to be a small one with electric start, I would like to know what it is.
Very cool and I have cellular phone, android. But there is no grid in many places with internet so how can this connect unless it has a cell service subscribed in to the controller. Like those little security cameras, you must have cable or a mobile hot-spot which must be connected/activated for use. We know things dont just 'connect' to the internet without a sim card and subscription.
Pls teach as a contactor authomatic start and stop connection with self starting and stoping not mobile app start and stop with single
I think this is great product. I would love to see this product being assembled on the more common "inverter generators" of 1000 watts or 2000 watts size (that would be a selling point for me and I'm sure for a lot of people as well). As there are 3000 watts generator with remote switch already in the market but no remote controled smaller size generators. I searched everywhere for small generator with remote control but I didn't find any in the market except yours (some DIY videos in YT I have seen are too technical for my liking, also not as good of a solution, and I don't have time to go deep into electronics to solve this issue and do trial and error unfortunately, Im looking for an easy solution). I hope you make video demonstration of your product on 1000 or 2000 watts inverter generators. I have your channel on my notification list and your website on favorite but I'm hesitant to buy without demonstration video of this product on an inverter generator size 2000 watts or smaller. Such video will give us confidence on its exact configuration and operation step by step on inverter generators of the mensioned sizes. So no guess work needed or uncertainty.
Hello @Mansur.
Our controllers can be fitted to any generator type or size. Although it must be equipped with an electric starter motor.
If you are referring to small 1000watt inverter types with a pull rope start, then this(or any other product) will not be able to auto start the generator.
It is not limited to Generators. The V2 AutoGen has also been fitted to petrol engine air compressors, petrol and diesel engine water pumps and other standalone engines.
As long as it has a starter motor, the V2 AutoGen can auto start and stop the engine. With or without choke on petrol engines, fuel injected, LPG conversions or decompression levers on diesel engines. So rest assured, we have a solution! The V2 is also customisable according to the application. Can receive a trigger to auto start from an ATS on mains power loss, pressure switches, water level sensors, battery banks, solar charge controllers etc. The sky is the limit!
That's because small generators do not come with electric start.
@@JM-yx1lm You do realise that what you are asking for is a small generator with No electric starter to have a remote start option? The reasons why small inverter type Generators are Small, is because the manufacturer needed to create a product that is lighter, smaller and more compact.
They designed it without a starter motor and lead acid starter battery for those reasons.
Hey Nick, if you have a wish list going on you can add Alexa thru the mobile phone...LOLOLOLOL
Hi NG... Never used Alexa before but can control the AutoGen via Google Assistant :)
How would this work in the middle of winter? My idea is to bolt a generator in the box of my pickup and run a cord to front so I can plug it in. Is it possible to come up with something that can program to run for 5 hrs then shut off?
Hi. It can be done, just need to protect the controller from the elements. It's not waterproof!
Timer is easy, we already have that available as a feature.
Good day, I am in South Africa and this product is the best I have seen, but, is it available in South Africa? Also where is this APP available, as I checked on PlayStore and nothing?
Hello Mervin. We do ship worldwide. Sent many to South Africa so far. You may view and purchase our products at www.dcautogen.com
Links to our AutoGen app are also available on our site. Keep in mind that the app can only be used with our products. There is a setup process when you install the controllers or generators as you need to scan the unique QR Code attached to device.
@@DCAutogen Thanks for the info, I did also find the App in playstore.
Can tou add 120 volt senseing , ro cause the genset to start on service loss then tripa transfer switch after stable power from genset
Yes, we can do that for you. Done it many times for customers.
Cost?
No extra cost Malcolm. Same price as on our website www.dcautogen.com
Hi mate.......I am chasing a unit to use as a 240 mains change over, with maybe output to turn on a contactor with 12v coil
Hello @ Carli Cameron.
Send me an email sales@dcautogen.com
Give me a brief understanding of what you require.
Does this have a LOW BATTERY VOLTAGE auto generator start feature?
Yes, you can adjust the low battery start setting within the app.
We have a pull start generator with an off switch, we use it to run a well on a lease property we have cattle on. It’s 30 miles one way from headquarters. We go down in the mornings Monday, Wednesday, Friday to feed and check cattle and to turn the generator on to fill up our overhead tank which feeds the water trough. After 8 hours we drive back down to turn the generator off. It’s not economical as you can imagine. Is there a way to put a timer off switch or a timer valve on the fuel line so that after 8-10 hours the generator will shut off?
Hello Travis, yes that is easily done with a 12v programmable digital timer.
Set it for X amount of time to trigger. Some models have an onboard relay which will shutdown your generator.
Fairly inexpensive.
If your generator had an electric starter, then with an AutoGen controller, everything would have been automated to start and stop when needed.
these are so awesome!
we are interested in installing a 100 amp hr 12V lithium battery in our travel trailer. Our plan is to use a small inverter generator with command start to maintain the battery and power appliances. The priority power draws are a 12V dc fridge that requires approximately 600W per day and the blower on our propane furnace. Lighting is all LED. The battery should service this load overnight and it would be desirable to have the generator to auto start to maintain the battery while we are away from the trailer.
Will the controller integrate with the generator's factory command start and also allow me to manually start the generator when we need to power larger appliances such as our AC? Most campgrounds also only allow generators to operate from 10am-6pm so there would also need to be a way to prevent the generator from auto starting during this timeframe in some instances.
Sorry if this post showed up twice.
Sure.
Best to go through the websites contact form.
Send us the details of your generator.
Just need to add engine RPM and engine temp and extra temp sensors for the generator shed temp while running and I’ll buy
These options can be added if you wish.
We can add an rpm sensor and 1 temp sensor. Need to check if we can add a 2nd temp sensor.
this is awesome but how do you get past the back feeding of the gridline if hooking to a house that is on the grid?
Hello Thomas.
Whenever running a backup generator if grid is down, you must use an Automatic Transfer Switch. This disconnects your distribution panel from main grid and generator feeds your distribution panel.
Generator interlock kit is cheaper than a transfer switch
Interlock kit.
Thanks for sharing. I have a MGC100 that i am trying to setup on my Champion 100110 but cannot figure out all the wiring yet. I have the crank (starter), b-, and b+ but cannot make sense of the other 3 wires needed. I currently made my own setup remotely in the garage to start the outdoor generator by duplicating the current onboard switch on the generator but want to use the MGC100 instead. Any thoughts? I think the EM Stop would be the one of the other three to stop the engine which leaves me with 2 remaining wires. The generator has a 6-pole combination switch that controls it all.
I have the MGC100 as well and couldnt get it to work. I switched to this and it works now. I think the MGC100 needs some relays added to it but the seller can't dumb the instructions down to my level. LOL
Hi, I have a wen 3750 dual fuel generator and want to connect it to Schneider electric AGS, the generator is just a key. Would this help me connect the generator to the AGS?
Hi Tony. Yes, sure can!
Check out the products on our online store.
Hi will this work on a troy bilt xp7000 series generator and a growatt sfp 3000 24v system
Hi. Looks pretty straightforward. If it has manual choke, you will also need our choke linear actuator.
Check out the V6 AutoGen smart controller on our website www.dcautogen.com
Is there a controller like this to convert a portable electric start to a 2 wire standby startup? My solar controller accepts generator input and has a 2 wire signal to start the generator. But my portable doesn't have 2 wire compatibility.
Yes, check out our newest AutoGen X smart controller.
hi nick, i have a Honda EU30is Generator with a manual choke. which version do i need ?
Hello Sotiri. You will need the V2 AutoGen 12v with Choke Servo. Is there anything else I can assist you with?
I want basic connection to make an automatic start and stop device for eu30is generator.
Hello.
Check out the V2 AutoGen 12v version on our online store dcautogen.com
What are you using for the choke circuit? Does that gen have some kinda electronic choke or did you rig up some solenoid to switch it on and off with the v2 signaling?
Im going to have to design a circuit that will hold off the starting sequence for a few seconds while the "choke" presses on a propane priming button to fill the carb with propane in order to start.. no physical choking necessary, you just have to prime the system for 5 seconds then immediately hit the starter so the propane will continue to flow with vacuum. Which aitomatically shuts if the gen shuts off.. im guessing the 5v circuit on the v2 can be setup like this maybe or will i have to make a little timer circuit that will pop on if power goes out then tell the v2 to start sequence..??
Hi. You can use our Choke Servo or Choke Linear Actuator. Both available on our online store.
Do you have an AutoGen controller already?
Send us an email with your requests so we can guide you. Some programming may need to be done for your controller.
Could it be used with a well pressure switch so it could start the generator when the pressure falls to 50psi and then kill it when the pressure reaches 80psi?
Hello. It can be done. Can I get a link to your pressure switch?
How do you start it from the app if power goes out and there's no wifi signal available?
You can provide power for your wifi router from a UPS or have the AutoGen controller start your generator when grid power is not available.
Wonder if there is anyway to program this device to automatically start the generator if let’s say I was on my boat and we were running devices off the house/boat batteries and wanted the generator to only start when the voltage dropped to a certain level? Would be a cool feature, although I guess most folks would just be using the generator w devices plugged directly into the generator and would have it running the entire time.....
Hi CrazyMoFo.
The V2 AutoGen controller already does that. It starts the generator when your battery bank falls below the user selected low battery voltage threshold within the app.
You can view more details at www.dcautogen.com
Nick Alexander thanks for the information , I visited your website and love it! I’ll be getting one this off season! Thanks again
will the generator automatically shut down when batteries are at full charge?
There are a few ways to approach this.
If your inverter/charger has a programmable dry contact relay, this can be programmed to send a start and stop signal to AutoGen according to battery bank state of charge.
If this is not available, you would need to add our DC current sensor which will calculate when to shutdown the generator by observing the tail current drop during the Absorbtion stage of charging. When current falls below a preset value, AutoGen controller will shutdown the generator.
It does not calculate state of charge though.
I want to buy one of these, but I would like to hook up a portable inverter generator to my off-grid solar system on my bus to supplement energy in the summer for an a/c unit on low setting if possible. Do you know where I can find information for setting up a backup generator to solar batteries? There seems to be no information on this.
Hello Zack. It is possible to install on an inverter generator. You may also find mppt solar charge controllers that accept input from an AC generator to charge your battery bank.
You can visit our website for more information on our products at www.dcautogen.com
hi
i have diesel keystart water pump...which versio do i need?
Hello. You will need the 12v version
dcautogen.com/product/v2-autogen-12v-controller/
will your kit be suitable for Böhmer-AG 3800KE - 3000w 8hp Petrol Generator - Electric Key Start
Hello.
Yes, it is compatible, but you will also need our Choke servo to operate the servo during startup.
Here is the link for your reference.
dcautogen.com/product/v2-autogen-12v-controller/
Brilliant, Where can I buy the kit?
Hello.
You can purchase all of our products directly from our online store at www.dcautogen.com
How do I wire a relay to it to auto start the gen when the power drops the relay out. I see aux1,2,3 on it are those used for that?
Hello John Chase. Do you have one of our V2 controllers?
@@DCAutogen Looking to buy one and I am trying to understand how the controller receives a hardwire start signal. We have a couple of rural WAN towers that we need backup on and I want to make sure this will work for us as opposed to buying a 7kw generac standby.
@@johnchase7667 the V2 is programmable so we can customise it accordingly. We can set it to start when a signal is received.
The V2 monitors a battery bank, if the voltage falls below a set threshold it will start the generator.
Example:
If you apply a 12v signal to the monitoring pin #10 and #12 via your relay, when the relay cuts the connections and no longer feeds 12v to those pins, the V2 will start your generator. When V2 receives 12v again on #10 and #12, it will kill the engine.
@@DCAutogen hi Nick. Love your videos mate. Bought a V2 AutoGen for my Honda EU is 3kw. Could you send me instructions on wiring to that. I got the choke servo too. My email is Jrcxley@gmail.com
Cheers. John Crossley.
P.S. I'm in The Gold Coast, Queensland.
Hello Can I use the ats system for electric motor?
Depending on the application, yes it can be used.
Sends an email with your requirements at sales@dcautogen.com
@@DCAutogen alright, so I Will let my contact to! Phone +258840501169
Email address: edmilsonedmilsonnobre@gmail.com
$300? that some sweet markup for a couple chips and relays.
The time and effort we spend with our clients pre and post sale for individual customization, by far surpasses the $300 price of our controller. Thanks ;)
Dude 300$ aint about shit when you look at about anything for a generator.. if you get a commercial stand alone is like 1-2 grand and has a bunch of features most people wont ever need to use or could use. If you go the auto start at the electric panel than by the time u get the transfer switch, breakers, sub feed to generator panel if not already but the transfer switch alone is pushing 300$..
I mean you probably own an iphone or samsung and spent close to a grand on it and its just a godamn phone..
You going to spend 1 monyh making mobile app for your phone xD I rather spend 300$
not a big fan of utilities that need an app to run... make it stand alone and i'm interested
Hello Jeff.
The V2 AutoGen is an automatic generator start controller. If you don't need the use of the app for monitoring, or manually starting from a remote location, then don't use the app. You can just install it and forget it, let it do its thing :)
Can this be setup on a Kubota 2cyl diesel with 12 volt alternator. Alternator needs 12 volt, glow plug, starter, fuel shut off. Can a proximity sensor be used for crank rotation so controller knows if engine is running or not?
The alternator produces 12v. This can provide the signal to controller to know that the engine is running.
Do you have a video for your V6 using an ATS switch? For example,, the ATS has a 12 volt DC built in it and yet the Generator has the 12 volt Battary and we just purchased the Solar charge. We just can't find it.
Sorry, don't understand what the questions are.
You want to know if the V6 AutoGen can be triggered from an ATS? Yes, that's easily done.
Good day sir you said connect the three important wire 1st is the kill switch second is for starter relay and for the 3rd sir you didn’t mention it? What is the 3rd wire
3rd is connected to generators 12v AC coil which is used to recharge the starter battery and to provide 12v DC max 8amps to external devices.
Okay sir, thank you so much more power to your youtube channel
@@alfredcruz7028 you may view our products on our site www.dcautogen.com
So if the electric is off how do you have internet
Extremely simple...run it off a battery backup
Hi , I purchased one of the V2 Auto Gen and can’t get it connected to the app. How can I get some support for my problem
You can talk with us through our website live chat service.
Hey !! How does the controller know when to stop cranking? Thanks 🙏🏽
Hi.
It can take either of the 2 available user options within AutoGen app:
Measured dc voltage of starter battery charging circuit or generator ac output.
@@DCAutogen Thanks !
Can i get this item in Singapore?
Www.dcautogen.com
Were can i buy one i am from south africa
www.dcautogen.com
okay great , but when the power goes out , so does the internet ........ so what happens when the internet drops ?
Cell booster
Run your router from a UPS
@@DCAutogen if the physical lines for the internet are down you can’t get it even with power. A cell booster is best. Most cell towers have generators. Get a cell booster and drastically improve your cell service. It won’t be as fast as WiFi, but it’ll be possible
Where Can I get one of these! Out of Stock
The V2 AutoGen is out of stock and no longer in production. It has been replaced by the V6 AutoGen smart controller available through our online store.
Will this work with my growatt spf 6000t dvm and a harbor freight 9000watt generator?
Yes
Aap ki range kitne hai
Does this need wifi? How will it work when power is out?
No, it doesn't need WiFi to operate.
It needs a 12v power supply. Therefore, by powering via your starter battery, it will operate when you Power goes out.
Hi, I have a generator with a manual choke, purchased new 2 days ago. Still can't get passed my head how a manual choke can b operated digitally (aren't manual chokes off a cable), I want to also know could this unit be fitted to a compressor as well to remotely start it? Both are 12v both key start with a manual choke compressor is deisel and generator is petrol.
Also can one of these handle the two unit or do I need one for ever unit? Do you have a place in Melbourne that can install?
Hello Morin.
Servos or solenoids are needed to operate the manual choke. We provide a digital servo and bracket with our AutoGen controllers for this purpose.
Visit our store dcautogen.com
Yes, has been installed in the past on engine driven compressors.
You need a controller on each engine unfortunately.
We are not located in Melbourne, Australia anymore. But I can find someone for you to assist with installing if the need arises.
Hi There. Just want to ask if where can i buy this auto start module...
Zandro Varquez please visit our website www.dcautogen.com for more info and prices.
This work on diesel generator ??
Yes, it does.
and you dont need to worry about wiring in a choke and actuator!
I have very littlle wifi connection at my cabin. Will this still work?
When you say little wifi, do you mean weak signal, slow speed, or data limitation per month?
@@DCAutogen It is pretty much non existent.
It can still operate without WiFi. All depends on how and when you want the generator to start and stop. Limitations of no WiFi is, no remote start or monitoring via AutoGen app.
@@DCAutogen i just want generator to start and stop when the batteries need charged and are fully charged without me having to be there.
Can be done.
Can this work on a generator that is using manual choke?
Hello Eze. Ofcourse!
The V2 AutoGen controller uses a digital servo to open and close the Choke during startup.
Here is a link of our V2 AutoGen controller. dcautogen.com/product/v2-autogen-12v-controller/
Directly sending a start signal without checking the status of generator can cause damage
That has been accounted for.
The AutoGen controller will never engage the starter as it receives a running signal on one of its inputs.
It always knows if it's running or not.
Gdmrning sir,please give me a diagram,
How do I know if this is compatible with my key electric start generator?
Hello J.
It's compatible with any electric start generator.
If your generator has a manual choke system, you will also need our choke servo.
Depending on your generator wiring, you might need to use external 12v relays to complete the installation.
Does the wifi mean it's connected to an internet? Or independent wifi?
Connects through wifi to the cloud. Then you can access it from any location.
I'm sorry I'm quite confused. Is there an alternative for that? I am worried if internet is cut from a hurricane then I might not be able to gain access via wifi?
If Internet is down and you are not onsite, you won't have access to the generator via AutoGen app.
Wonder if its a monthly fee for the app..
No
I feel like this won’t work when power goes out. If power turns off then your WiFi will also, cutting off the command between the module and your app... if you can prove me wrong, I’ll buy one.
Hello Jake. The controller still operates in Auto mode even without an Internet connection. It can be programmed to start if monitoring a battery bank, if utility power goes down, if on a timer etc. WiFi is needed only to monitor, remote start and to update any user settings.
Is there something else you would like to ask?
Another option is to keep your WiFi router on a UPS, if Power goes out, the router will still be active.
No idea of this is still an active thread or not. I would like to run a predator 9500 inverter generator tied to a Sol Ark 15k, what's your thoughts on running the 2wire start out of the Sol Ark to run this controller?
I think I figured it out. Looking at your V6....using the ac inputs and a NC relay, snagging a power source (have to figure out what the 2 wire circuit on Sol Ark requires) for the coil side....run any ac power to the contact sides of the relay then to your controller on the AC input. When the Sol Ark calls for generator, it would close its relay completing the circuit, activating the relay coil, opening the contacts on the relay. Your controller would see that break, then know to start up the generator. When the Sol Ark is satisfied....it opens its relay turning the relay back to NC....your controller now has AC...then knows to stop the gen set.
If you see another way....or have a controller actually set up to support a 2 wire start from inverter...let me know, please.
Hi Wade.
The AC inputs L and N are used as a generator running signal.
For 2 wire start function we use pin#12.
Whenever this input senses +12vdc it will trigger an autostart and 0v will shutdown.
@@DCAutogen nice! Thank you.
sol ark has starter delay . you don't need no $$$$ controller . you can get away with 3 NC relay relays( they like $15 for 3 pack on amazon). its what I did for my sol ark with predator inverter. tested and works great
How do you control the manual choke
you would have to add a electric servo.
Visit us at www.dcautogen.com for more info and prices.
how do i buy i of v2autogen 4rv
Check out our online store www.dcautogen.com
Do you have something for Koel 15kva ! With modbus??
Hello Rahul. The V2 AutoGen is compatible with the Koel but its communication is via wifi. Not modbus.
No I am asking how to hook this up with the genset panel! Does it support modbus? Or how will it communicate
The V2 connects to starter motor relay for starting. It also connects to fuel relay or coil to kill the engine. Communication between V2 and mobile app is over the internet. V2 connects via wifi.
To find more info on the V2 AutoGen please visit us at www.dcautogen.com
Can this shift the AFM settings to manual?
Edit: AMF means automatic mains faliure / switch
@@rahuldogra If you only require a signal to be sent to the AMF to switch on or off, then yes it can be done via our app.
Do you need to operate the generator remotely?
If you also only need signals sent to the Koels panel for remote start and stop, this cam also be done.
how the box know that the engine star to run it self for stop the electric star motor???
Hello VENDINGMEXICO.
This is sensed via the generators 12v output or charging coils.
How far can the generator self reduce?
Sorry, don't understand what you mean.
How much is this device
www.dcautogen.com for more info on our products.
Is this unit compatible with an HPS12000HE Winco Honda GX630 with Electric Start? Thanks!
and if so, what would I need? I'm assuming 12V controller and Choke Servo?
Hello danjjr. Yes, I believe there is a manual choke on that model, so you will need the choke servo with a V2 AutoGen 12v controller.
Is it equipped with any safety cut off solenoids for the LPG?
@@DCAutogen Okay, thanks. Yes, the safety cut off is an additional accessory and I'm thinking about buying it: www.wincogen.com/product/low-pressure-fuel-solenoid/
Should have been added as a standard option in my opinion.
Either way, the V2 AutoGen can be fitted easily.
You may find our products here.
www.dcautogen.com
Does this controller wire to the safety shut off or no?
Very fabulastic
Thank you Raheem!
Where is this product available
Hello. You may find our products at www.dcautogen.com
If there is not power is not internet
Some essential things can always be powered by a backup system. UPS can provide power to small loads.
Some modems/routers can be powered by 12v.
There is always a solution...
Shut up, and take my money!!!
Thank you Darko for your enthusiastic comment! Your order will be prepared soon.
@@DCAutogen you surely made superb product and it is precisely what I'm looking for. Thank you for your quick response.
Does it have a timer on it
Hello Leo.
Yes it has a daily timer which you can set to start and stop.
Also has run timers after the generator has started.
All these can be set via AutoGen app.
Thanks for the quick reply. Will it work without wifi? And will it work on my honda eu7000 is? If so please send link I need one
@@DCAutogen I just need the timer to work, do I need wifi for that? Or will it work via Bluetooth
To run the daily timers, it will need an Internet connection via WiFi. Yes, it is compatible with the Honda EU7000
No Bluetooth connectivity.
You can view our products here www.dcautogen.com for more information.
Is the app owned by yall?
Yes we supply the app with username and password with the purchase of our V2 or V4 AutoGen generators or controllers.
YOU had me. Until you said internet!!!!!!!!!!!! Why!!!!!!!!!!!!
Hello Dan.
The app and controller need an internet connection to operate or monitor the generator from any location. Their is no other way unfortunately. But the AutoGen can still operate in Auto Mode without internet. It will monitor battery bank level or loss of grid power and start the generator.
Hope this helps.
Great system but it's double the price of my generator can't afford that
Hello Emiel. Can't help with that unfortunately.
Hi Nick I'm trying to contact you but don't know how to get your email address. I'd like to know what parts are used and where to purchase everything. Thank you for your time and I look forward to your response.
Hi Andre. You can find more info at www.dcautogen.com
I need to start and stop a generator 900 miles away. A little WiFi probably isn't going to help.
If wifi internet or GSM service is available at generator site, then distance doesn't matter.
apna address Din
This work without wifi when there’s no power
Yes, it works without WiFi. Although there are ways to keep your WiFi connection even when power is no longer available.
It’s not “earth”… it’s negative you dope!
does it have a maintenance feature where it can start the generator every month for maybe 10, 20, or 30 minutes?
Hello Johnny.
Yes it does. You can select the days, time and the period to run for all within the app.