Hi. I have 3 questions 1- the led that u used is 3mm or 5mm? 2- i must use 10 k or 1 k resistor? Because in diagram is 1k! 3- the distance between leds?
Hola unas preguntas, la fila 4 (Row4) es la superior o inferior . ¿los alambres de las filas tienen chocan en las otras filas o no ? Por ejemplo fila 1 choca con alguna otra fila)
Olá, estou montando esse projeto, contudo me deparei com uma dificuldade, no vídeo não dá pra ver o que faz com o 2N2222, como soldou as pernas dele, poderia me enviar um diagrama de como ficaram as ligações?
Hola 2 preguntas, ¿la fila 1 es la superior o inferior? El alambre que va de la dila superior chica con las de la fila inferior ? Por ejemplo suponiendo que la fila 1 es la superior esta choca con la fila 2,3 y4 ?
Hello, I have a question, I already made all of the squares with the leds, but all my negative legs are on the right side, and now i just saw that you have half of them on right and other half on left. Will that change my final product?
Correct me if I'm wrong, but these wires are not insulated, therefore when live they will shock if touched. Why not use insulated wires? Simply remove the insulation where necessary.
The transistors are there so the microcontroller doesn't need to power the LEDs directly! Which might frie it up, so you connect the LEDs to a power source and with the signal from the microcontroller open and close the "switch"(transistor).
@@DIYBuilder but i got a question, when I verify the code, it tells me "warning: narrowing conversion of '1.75e+1' from 'double' to 'char' inside". Is that normal?
@@DIYBuilder also i've seen other videos where they would only use 4 resistors and the arduino Nano. Will the code works without all of your other components? Because I don't have them.
The anodes of the LEDs are connected in columns and all of the cathodes in a layer are connected. By applying + voltage to a column and selecting which layer the current can flow out of will address an individual LED.
If you need a circuit diagram can't you just pause and look and take like idk 3 maybe 6 seconds to figure it out? Seriously, I don't even do anything with circuits, boards, soldering hardware or anything that has to do with putting together things, except some easy fixes with a hot glue gun and one upgrade, and a few controller mods that usually were exterior only, I havn't messed with electronics at all, at least from the out side, and I can totally understand how the electric flow works and I don't even know any terms. Lazy, just pause and think, seriously.
haven’t got my head around how it’s addressing each LED individually, mind blowing stuff!
Even me🙄🙄
Nice tutorial, just finished mine and it all works first time with no troubleshooting. Thanks!
Help me please
Coppy and paste the code here please
Hey does that require any batteries
@@aaroncodm404 no, no power required, LEDs just light up spontaneously
Hola, un favor podrías explicarme , las cual es la (fila 4 /row 4) la de superior o la de inferior
Look forward to seeing the code on this. Great cube
Hello, thank you very much for your time and video, I have a 3mm led, the resistors are worth it and what else you put in materials? thanks
Hi. I have 3 questions
1- the led that u used is 3mm or 5mm?
2- i must use 10 k or 1 k resistor? Because in diagram is 1k!
3- the distance between leds?
1. 3mm
2. 10k
3.1 inch
@@saquibdasurkar5675 why you need 10k resistance for led ?😑
Great video. What kind of wire was used? Did you buy a spool or some kind of rod. What gauge and material? Thanks.
Hi! Really nice tutorial. I have a question...Can i use pro mini instead the nano? I think yes, but better to ask you)
thanks for good tutorial
Hi
First, i am a little bit confused about the power supply of the circuit, an explanation would be great.
Second, what is the voltage of the LEDs?
Powered by the 5v supplied via the USB cable
The power comes from the arduino.. 5v
Hola unas preguntas, la fila 4 (Row4) es la superior o inferior .
¿los alambres de las filas tienen chocan en las otras filas o no ? Por ejemplo fila 1 choca con alguna otra fila)
I have a doubt should the led be placed according to the (+ )(-) terminal??
I know connection are same but we can use Aurdino Uno r3 in place of nano? By following same connection pin
I am looking at the diagram but cant figure out your column order can you explain what pin goes where
you can find it in description section
Sir we can use aurdino Uno r3 in place of that codes are applicable same
Olá, estou montando esse projeto, contudo me deparei com uma dificuldade, no vídeo não dá pra ver o que faz com o 2N2222, como soldou as pernas dele, poderia me enviar um diagrama de como ficaram as ligações?
Hi. I have 1 question
The 2n2222A works?
since you used the 2n2222P
8:54 what type of material is that
I had made one without transistor. I want to know if ur led cube
is more brithness with transistor.
Can i change arduino nano with uno? Will it work correctly?
UNO is more powerful than Nano with same output pins. Yes same codes will work on both.
Hola 2 preguntas, ¿la fila 1 es la superior o inferior? El alambre que va de la dila superior chica con las de la fila inferior ? Por ejemplo suponiendo que la fila 1 es la superior esta choca con la fila 2,3 y4 ?
Can please explain your lighting setups
What are these so many colour wair?
Hi bro,
I can use resistor 10k or 1k because different between your circuit diagram and the link of parts?
sir you can be video on how meny L.E.D s , how meny resistor and how meny wire s
Can I put it for 5*5*5 cube by change the code .ie initialising 5 instead of 4
you don't have enough i/o pin on the arduino for that
Did you twist the wires?
with a drill to make them straight
@@TalalTheScienceGuy Thanks for the reply . I have completed my led cube 6 or 8 months ago
May I know how many sequences this has?
The emitter of 2n2222 it is on ground?
yeah
How to change the light pattern
can this be made with arduino uno??
8mm led se banayega kya sir
Led are in series or parellel
How do you edit your videos
How much gauge copper wire you used in this? Please answer this
Can i use 9013?
Hello, I have a question, I already made all of the squares with the leds, but all my negative legs are on the right side, and now i just saw that you have half of them on right and other half on left. Will that change my final product?
yep, on the left side the led's cathodes have to be on the right (2 rows of led's) on 2nd side (right) the cathodes have to be towards the left
Can i use BC547 transistor?
Yes you can use it
Can I make this without transistor
Correct me if I'm wrong, but these wires are not insulated, therefore when live they will shock if touched. Why not use insulated wires? Simply remove the insulation where necessary.
I dont think he is putting like 100voltsin that circuit
There was a bug (an ant?) strolling around on your project while video recording at 8.:12 to 8:15. Did he survive?
I have a science project day after tomorrow I just need to know what is the power supply
beuttifull LED cube
how do you power it
Hi dude, I have many question. First, how you connect polarity led?
cathode inside annode outside ( the legs of the cube is annode)
Sir provide circuit description and it's components plzz do fast reply 🤟
what if we leave the Transistors ? what is the advantage of using the transistors any body ! Thank you
The transistors are there so the microcontroller doesn't need to power the LEDs directly! Which might frie it up, so you connect the LEDs to a power source and with the signal from the microcontroller open and close the "switch"(transistor).
220R resistors are 12 Ω resistors
no they are not
Excuse me its a bit late but can this also be used arduino uno? Just askin for our project
Yeah
Can the codes be applied to arduino uno?
Mat ka size kya hai?
From where i can get those rods ?
Offline store
Brother what are these rods called plz tell me i need them
@@thechannel4666 its just copper wire made straight with a drill
What happen if i not use resistor
if I connect the arduino to the pc it work but can I use it if I connect it to the power outlet with a power supply?
You need to read how an Arduino works before asking
Programig kese ki aapne ye btao pls
I lovet but where is the shematics can you put the shematics pls in the description
Can we give 5v for arduino board vin and gnd
Yes
Instead of light can I add text
Good!
Where is the code ? Can't find it in the description.
the codes man not the exact thing appeared on the YT video in here in my project
the code hasn't have the same effects showed in the video?
Gwyneth Alyssa you might have done your wiring different
In the video he did the wiring wrong
because green wire connected to D13,A4A5 and D1
Could you put the code in the description please?
check it again i have put the link in description section. if you need any help, you can ask me feelfree.
@@DIYBuilder thank you soo much man! I appreciate it a lot
Welcome man
@@DIYBuilder but i got a question, when I verify the code, it tells me "warning: narrowing conversion of '1.75e+1' from 'double' to 'char' inside". Is that normal?
@@DIYBuilder also i've seen other videos where they would only use 4 resistors and the arduino Nano. Will the code works without all of your other components? Because I don't have them.
where is circuit diagram
it is not in discription
plz reply fast
as soon as possible
Bro sorry for it. I'll update it as soon as possible.
@@DIYBuilder PLEASE UPDATE IT
hello :-)
i need help..i have transistors 2n2222A is it problem?
No
2n2222A is better than 2n2222, u will be fine
Ai led gulo kon tar diye connect ko6en sir
it is so beautiful.But the code has expired😢
Do we need to download any library for arduino ide??Please reply🙏🙏
Bro! I Couldn't find the codes anymore. Would you be kind enough to upload it again?
The code link is not working!
Plz give circuit diagram
name of music playing at beginning
Can you share the circuit diagram, please!?
i want too
I also too
were is the alimentation please
Could you share the circuit diagram? Please!
There is one blue led in the led cube
i am not able to upload the code onto arduino nano (it says: error compiling for board Arduino nano) can anybody help me pls??
Maybe board is bad
Please copy and paste the code for me.
go ahead and use an uno to upload the code or make sure the board is set to nano in arduino software
The code is not arranged, my ide fine alots of error massage, please make it easier for me, by copy and paste the code here for me.
i cant understnad why circuit and circuit in this video is different.
I need Circuit diagram...
I will update it as soon as possible.
I can't fine any code.
A one my friend
Dute cannot you make this more simple and easy.It is not quite difficult for pro but for beginners is difficult.
The code have some errors, how to remove them?
use older version of arduino IDE which contains avr library
@@707malvin yep, its superb. Its working, so amazing
I don't get how it's able to address single LEDs in that circuit
The anodes of the LEDs are connected in columns and all of the cathodes in a layer are connected. By applying + voltage to a column and selecting which layer the current can flow out of will address an individual LED.
@@rudymcintyre385 thanks for explaining, now I get it :)
@@vladen14basically it's like an AND gate.
I need led diagram
I can't understand plus or mins
Kya ???
cathode inside, annode outside (annode is legs of cube)
bhalo hoache aro bhalo korte hobe.... tumi 'ক' payacho ..
Ok bhai 😁
Great...
Please make 8x8x8 led cube
Can you give me the Arduino code?
Jo chiz slow dikhani chahiye wo fast and jo fast wo slow dikhata hai
The code is showing error
Circuit diagram
I will update the link soon
Circuit diagram i need
I will update it tomorrow.
@@DIYBuilder circuit diagram
Bro the code showed has an error in it
When you copied it there may be Error it is simple to correct it
Hi, I want the schematic diagram please..thank you
Bro, the code doesn't work, please gimme the real code
Where are you ????
India
Suvo da Ami himansu
Wow
wrong code
lol
If you need a circuit diagram can't you just pause and look and take like idk 3 maybe 6 seconds to figure it out? Seriously, I don't even do anything with circuits, boards, soldering hardware or anything that has to do with putting together things, except some easy fixes with a hot glue gun and one upgrade, and a few controller mods that usually were exterior only, I havn't messed with electronics at all, at least from the out side, and I can totally understand how the electric flow works and I don't even know any terms. Lazy, just pause and think, seriously.