For anyone struggling at the 5:00 mark and the cable clip here's what I was able to do that matched what was in the video after very careful examination. You are straightening the cable as much as possible after it is plugged into the extruder. If you are facing the printer, place your hands where the cable lines up with the left tie rod and fold it like a taco towards you. You are going to take the clip, pry open the closed section with your hand, and squeeze the cable inside both spots on the clip. Put the clip peg first into the holes at the top near the tie rod like in the video, then screw in the screw. It took me a minute to hold everything in place but I eventually got it.
This assembly tutorial is world class editing, recording angles and choices of backgrounday, they force people to do things slowly! So many times what is being done is blocked by the machine and/or the person. Then having the black t-shirt as the background so you can't really see the dark colored parts well, and the white texts are usually using the white desk as background so they don't stand out at all!
@@martinlibrefree I actually have 10 of them now. I have 2 at home and 8 (Plus & Max) at work. Learn to keep the bed level and the Elegoo Neptune 4 (Plus & Max) prints great. Good luck.
At the 5:11 mark can you seriously slow down and actually show what you’re doing???? Wiggling your hand around as fast as you can then moving on doesn’t help at all.
Also maybe don’t wear a black shirt when you’re putting a black harness onto a black cable onto a black 3d printer… I seriously hope I can find a better video than this.
I dropped one of the small screw that goes to the top of the rod at 4:18. It fell into one of the holes in the printer, and now I don't know what to do...
Check the red voltage switch is set correctly for your region. It's located in the left side of the machine in a hole next to the vertical frame/gantry support. Super obvious once you find it, but seems like it would be easier to find if it was next to the power switch, like it usually is.
On the left side of the printer, there would be a hole with a switch between the 2 voltages, uses an Alen wrench or a screwdriver, and uses it to reach into the hole and push the switch to the left or right depending on the voltage needed.
![Unboxing & First print Elegoo Neptune 4 Plus - Assembling and Start-up [Tool Update EN]](http://i.ytimg.com/vi/Toidb2EJAgk/mqdefault.jpg)
For anyone struggling at the 5:00 mark and the cable clip here's what I was able to do that matched what was in the video after very careful examination. You are straightening the cable as much as possible after it is plugged into the extruder. If you are facing the printer, place your hands where the cable lines up with the left tie rod and fold it like a taco towards you. You are going to take the clip, pry open the closed section with your hand, and squeeze the cable inside both spots on the clip. Put the clip peg first into the holes at the top near the tie rod like in the video, then screw in the screw. It took me a minute to hold everything in place but I eventually got it.
Thank you, I would have been stuck for a good 10min trying to understand exactly what he was doing🙏
This assembly tutorial is world class editing, recording angles and choices of backgrounday, they force people to do things slowly!
So many times what is being done is blocked by the machine and/or the person. Then having the black t-shirt as the background so you can't really see the dark colored parts well, and the white texts are usually using the white desk as background so they don't stand out at all!
Ordered the Elegoo Neptune 4 plus today. Will be delivered Saturday. Just here to get a head start.
Got mine today, any tips?
@@martinlibrefree I actually have 10 of them now. I have 2 at home and 8 (Plus & Max) at work. Learn to keep the bed level and the Elegoo Neptune 4 (Plus & Max) prints great. Good luck.
Same, but today haha
Your video steps are not properly visible to assembly this printer
Excellent video, followed this from start to finish and I was printing in about 2 hours.
At the 5:11 mark can you seriously slow down and actually show what you’re doing???? Wiggling your hand around as fast as you can then moving on doesn’t help at all.
Also maybe don’t wear a black shirt when you’re putting a black harness onto a black cable onto a black 3d printer… I seriously hope I can find a better video than this.
I bought a Elegoo Neptune 4 plus and I am really happy with it👍🏼👍🏼
I dropped one of the small screw that goes to the top of the rod at 4:18. It fell into one of the holes in the printer, and now I don't know what to do...
….. the same thing happened to me right after reading your comment and now i feel a cosmic level of dread
Might need to use double sided tape on a stick to get it out
Is the filament detector supposed to be super loose and just kind of dangle there?
Yes
what size nozzle come with? and how many different size?: 0.2? 0.4? 0.6? 0.8?????
.4
Just bought one of these and have missing washers, not a great start.
How much shipping gross weight and volumetric weight for Elegoo Neptune 4 Plus ?
My printer cant find any networks, other than a mobile hotspot, any reason why?
Quiero una, ya están corregidos los problemas de finware? Saludos!
My printer doesn’t seem to boot up, it just sits there with a black screen and hums a bit nothing else
Check the red voltage switch is set correctly for your region. It's located in the left side of the machine in a hole next to the vertical frame/gantry support. Super obvious once you find it, but seems like it would be easier to find if it was next to the power switch, like it usually is.
@@foonarf that’s it! Thanks man I was about to contact Elegoo for a refund!
@@foonarfHey I’m having the same problem but I found the hole and I don’t feel or see the red switch you are talking about
Update I got it thanks for the help
@@PhoenixGamer-hb5yy It's buried in there :-)
Mine centers off center and doesn't go all the way down. :(
How to fix the problem with the WiFi card? After updating to ...64. connecting to Wi-Fi causes the LED to blink and the printer to restart?
I did the same and my elegoo not turn on 😢
Just got this printer and i already used an entire spool
Not a good start
Чудовий принтер. Маю такий самий.
Elle fonctionne bien ? Car je pense la prendre aussi
Why does my Neptune 4 Plus just level on 6x6 points?😢
Please email to 3dp@elegoo.com and our staff will help you further.
Good video
just opened this, set it up, plugged everything in, and it won't even turn on. WTF? ANSWER... SWITCH THE VOLTAGE TO YOUR NEEDS, VERY IMPORTANT.
On the left side of the printer, there would be a hole with a switch between the 2 voltages, uses an Alen wrench or a screwdriver, and uses it to reach into the hole and push the switch to the left or right depending on the voltage needed.
the spool holder and a couple other items are facing different directions than in the video