Few People Know This Circular Saw Secret! Cut Like Pros With Saw
Вставка
- Опубліковано 25 сер 2022
- When sawing, small chips always come out of the boards and the cut is often not smooth. In this video, we show you how to cut properly every time when cutting with a circular saw. If you are wondering how to cut properly with a saw, be sure to watch this video.
- Навчання та стиль
60 T plywood ( finish ) blade, and a little less blade depth, and you're golden
Для фанеры надо брать диск с большим числом зубьев (40). И самое простое - это использовать малярную ленту. На ней и размечать проще. И видно лучше.
Great ideas! Thank you!
Very nice video. Descriptive and clear. Thank you bro
Very professional work, Thanks my friend, Big like ♥️♥️♥️♥️♥️
Gute und praktische Tipps, manche bekannt, manche nicht bekannt, aber auf jeden Fall danke...
Спасибо! Полезная информация!
Заготовку переверни… там чистый рез… 🤣🤣🤣 вот тебе главный секрет циркулярки… 🤣🤣🤣
Excelente!!! Gracias totales
Great tips if your on a budget and can only afford a 24T general purpose blade(framing Blade). If you cut a lot of boards, and can afford it, get a blade with more teath 40T or even 60T if you need really fine edges on both sides.
You would have to be on an extremely tight budget an Avanti 7 1/4 OSB/plywood circular saw blade is like $8 at Home Depot and the Diablo 60 tooth fine finish is about $22. There is no excuse for the wrong blade.
No matter the number of teeth, chipping can be completely prevented only by special measures.
@@trex2621 rubbish! Table saw, chop saw, circular saw are all improved by the correct blade for the material. Try a 100T Frued blade against a chinese 20 tooth. If you think "special measures" is cutting through masking tape, best of luck getting the melted glue off the blade later! Also strange how the Rob Cosmans and other furniture makers dont use "special measures" to avoid breakout from saw blades. Try it yourself, cut a piece of say, hardboard with a 7tpl rip saw. Note the ragged edge. Now use a 24tpi fine toothed saw and note the edge. End of conversation!
@@gbwildlifeuk8269 By "special measures" I first and foremost meant scoring.
¡¡¡¡¡¡¡¡¡Excelente!!!!!!. Hay tantos trucos para aprender y darle buena utilidad a la herramientas
Fijne video weer. Bedankt voor het delen 👍🏻
Great video must try the stuck on plastic sheet.
How about putting an actual finishing blade on instead of a rough framing blade lol
Exactly!! Start with that and use a saw guide to keep the blade from wandering. Did you notice how he rammed the first cut?
Scribing with a blade really speeds up the process😂😂
I agree. he's using a rip blade on a cross cut.
If he had altered the blade depth to a shallow cut, the amount of brake out would be greatly reduced.
Exactly and a good brand
The fact that you were plowing thru quickly on the first cut and much slower on the others had everything to do with all the slivers.
Thanks, from Russia with respect))
Habe mich schon oft über den entstehenden Grat geaergert wie im 1ten Schnitt gezeigt. Nun nicht mehr fank der darauf folgenden Info? Eine absolut tolle reale Info meint Bastler Roland
Weiter so mit Top-Info wünscht Roland Doppellob verdient!!
OBRIGADO. Gostei MUITO
Obrigado, muito bom!!!!
Cool, appreciate it
Love you dude
Да! Канал отличный! Если даже ролик не по моей тематике, всеравно смотрю с удовольствием и до конца.
Nice
Or you could just set the depth on the saw so the blade just goes a tiny bit past the thickness of the board
Just my words 😉
very cool try it
Я дико извиняюсь, но у меня аккушный зелёный Bosch v18 пилит лучше без всех этих прибамбасов. Может просто нужно диск поменять ? Птичку ( кусок фанеры) жалко. 😊
Совершенно верно. Там стоит диск для продольного реза.
nice video
КРАСАВЧИК!!!
영상 잘 보았습니다! 또 오겠습니다!
شكرا 👍
Mantap...
Красавчик 👍🏻
Красавчик!
Baseplate is easy and universal and only takes a few mm off the cut depth
gute Tipps ✔
Друг, нормальный диск нужно использовать, хотя бы на 40 зубьев
классный канал
If you use the other side of the board you'll have a perfectly smooth cut.
super :)
❤️❤️❤️❤️❤️❤️❤️❤️❤️
Was shown this when I was 14. I am now 70. It was common knowledge then and now. Also score line with a sharp utility knife not a new concept.
How about using a plywood blade on plywood ?
Отличные задумки 🙏🙏🙏
👏👏👏
Да, знаем этот эффект с малярным скотчем. Дверь подпиливали, было дело ))
Ich hatte 2021 das mit dem Tapetenband gemacht. Nur, beim letzten Schnitt klemmte das Band. Ich wollte das Band wegziehen. Nur habe ich die Säge nicht gebremst. Glück gehabt. Finger ist nur leicht getroffen worden. Hatte dann 6 Wochen Entschleunigungszeit. Ich benutze diese kreissäge seit 17 Jahren. Von Feinarbeiten bis Stämme zu Feuerholz. Und einmal klappt es eben doch. Also: IMMER schön aufpassen.
Nr 3
👍👍👍
Rompe porque tenes una hoja para tronzar madera ,para cortar multilaminado tiene que tener mas cantidad de dientes
Количество зубьев на диске надо уменьшить до трех))))
это гениально
Согласен с последними тропы способами. Кроме скотча...
Диск пильный надо подбирать соответствующий.
Show 👍👍👍🇧🇷🇧🇷🇧🇷🇧🇷👏👏👏
А диск правильно установлен?
Muss sich bei einer Kreissäge das Blatt links herum drehen ( also die Späne nach oben werfen ? )
Ещё не мешало бы диск для чистого пропила поставить
На 100% уверен, все будут использовать второй способ)
What is best saw blade for plywood?
How about safety???
IMO - DON'T ZIP TIE THE BLADE GUARD
Yes it's to protect the blade when not in use but it also is a reminder for your fingers.
別に秘密じゃないだろう、裏技と言うべき!😊
Where I worked for years Building Homes if you tie down your blade guard the supervisor would tell you to get a tool out of your truck that he needed. When you got to your truck you would find your last paycheck under the windshield wiper with your saw sitting on the hood. There was NO EXCEPTIONS. No matter how long you work there. You were gone.
👍👍🖐🖐
Поставь диск с напайками и не страдай ))))
Кон гениальна
I know a 74 year old guy that knows all that and has a plexglass plate bolted to his saw because it the quickest way.
El sistema es bueno, real pero con una hoja de sierra de más dientes ( 100,- 110) y dejando solo tres dientes por sobre el espesor de la madera. Lo que muestra el video es el corte por encima ye el problema se produce por debajo. Con ese disco que usó hizo trizas la madera.
First comment
Lo conocen todos los que trabajan con ellas
Will last a long time ,what does that mean.
А самое простое не показал. Нужна только пила и ничего больше, ни скотча, ни оргстекла ни жертвенной дощечки.
Ставим половину глубины и пилим обратным резом- пила идет спереди назад, потом на всю глубину и вперед
Думал что откроет реальный секрет.... Этот секрет у нас любой школьник знает... Но судя по количеству комментов на латыни, невольно вспоминается уважаемый Михаил Николаевич Задорнов... "Ну тупые!!!!!!!!" 🤣
💯💯💯💯💯💯💯👌👍👍🤝
You have the saw blade installed the other way around!
No he doesn't
Blade on my Dewalt doesn’t sit at 90 degrees. Almost but not 90. Won’t adjust further.
My cheap black and decker battery op and hyper tough are that way...was going to spring for a dewalt but now I won't. Probably China manufacturing. I was sure it was just cheap saws but now I wonder. My cuts are so far off I can't make a good joint for the life of me.
should keep finish side down as well.
does it saw, go throu glass like that?
If you now use the right saw blade for the right material you will not have the problem. Now you have a saw blade for trimming / scalloping . Too coarse teeth. Get a saw with more teeth. And saw calmer.
Mirar de poner una sierra con más dientes especiales para melamina esta es de madera
That is a ripping blade not a plywood blade.
Вот испоганил такой шикарный лист фанеры😆
Just change the blade.. that's a rip cut blade. If you don't have a finishing blade then go for this technique. ✌
try cutting it with the finished side down huh lmfao
Get a diablo blade and none of this wil be necessary . The blade on that saw is vary old tooth technology. Just facts
Keep wire tying the blade guard down(open) and you will not have that thumb of yours.
🤣😝🤣👍
La sega gira al contrario...
Ты серьезно.!? Я думал ты сейчас откроешь «мега- секреты» О которых я не знал…
Прям из закрытых архивов ФСБ секреты!!!
А ещё можно пропилить на минимальную глубину обратным ходом, А потом уже пропилить на всю глубину нормально
Это секрет малярного скотча а не пилы)
Con un disco con mas dientes tambien te cortaria mas fino , si puedes lo compras y ya diras
not a very fine blade for plywood.
Ну дык, в первом случае так надавил, пила чуть не заглохла, зато в остальных еле тащился, как будто броню от танка лобзиком пилил
Ничего нового!!!
спец- видно по залишкам пальців
с бумажной малярной лентой пожароопасненько..
You're using a framing rough cut saw blade to cut finish grade plywood why would you not use the proper blade and cut a curve
What's da Matter, cat got your tongue?
Ну конечно, что ещё может посоветовать профессионал. Только нахрен снять защитный кожух. Ты и верхний сними, так запил будет ещё чище.
Ничего нового
Ты что глухонемой ? ,- да ! )