Massey Ferguson Tech Tip: Compact Tractor Loader Removal
Вставка
- Опубліковано 29 чер 2024
- Massey Ferguson Compact & SubCompact Tractors offer Quick Attach/Detach Loaders...this video shows how to remove & re-install the loader. This was filmed using the GC1715 with DL95 Loader. Hope it helps to get more out of your Massey Ferguson.
- Авто та транспорт
It's about time that some one show that good job
Very helpful. I have a new GC1710 and could not get the top pins of the loader to unseat. Therefore, I stood on front of loader bucket to unseat the top pins. A lot of steps to ultimately use the mid-mount mower. Thanks for the tip about standing on the bucket. Removing the backhoe was much simpler. Thanks again.
New Paint on loader brackets and loader frame make the first few times a little more effort until the paint gets smoothed up. You can step in the bucket or pick up a little weight on this series of loader and it will help tell things get smoothed out. I'd rather see things a little tight at the start than loose and then wear even looser over time. Hope that helps.
Vahrenberg Implement; I put a little lubricant grease where the loader and tractor join to make the next time a bit easier. My initial 10 minute loader disconnect turned into a 30 minute fiasco b/c I thought I was doing something incorrectly so I viewed your video which cleared things up. Thanks. Don
I would recommend Anti-Seize versus Grease as Grease will attract dirt & dust and could compound the problem. Plus as temperatures rise the oil will ooze out of the grease.
Thanks. Have a safe Independence Day and may God continue to bless our great nation.
Thanks for sharing
I appreciate you doing this. I may have adked you a few months ago.I have been asking AGCO for a helper video since March 2015. I guess this is good enough since you are selling AGCO products. I may call them and compliment your business for doing such a good deed. I bought mine in March, last year and have yet to be able to remove it. I also have been having hard time with the 60in mower deck and backhoe. It may be because I don't have any level surfaces. I am hoping to get me a small pole barn built that will hopefully make this easier.
We have plans for Mid Mount Mower Connection Video and Backhoe Removal Video too. Just need to have a GC Series in Stock long enough to get filmed...they selling faster than we can get.
The surface doesn't have to be 100% perfect level but the more level it is the easier to remove and reinstall.
+Vahrenberg Implement that little thing that hangs in front may need adjusted, but not for sure.
+Vahrenberg Implement Thanks for replying.
Second the request for the mid mount mower removal and reinstall. I've seen a video for just about every sub compact tractor but Massey for this. I'm considering one but want to see this before pulling the trigger. It's my understanding that there's a 60" drive over deck. Would like to see how that works. Great videos and thanks.
I'm trying...It should come up this week. We can't keep GC Series Compacts instock long enough to shot a video and going to try as I have 2 more coming in but they are already presold. Might be a quick video before they take them home. Wish I had a tractor instock long enough to do everything but time and work commitments interfere with producing videos.
Good video. I have a gc2400 and have a hard time getting the hydraulics out of the system when reinstalling the loader. I move the control handle as shown and eve bleed the hose tips on a hard surface but at least one of the connectors won't seat. Other tips? I work the tractor all year and it's great. Just don't find the process of switching the loader and snow blower to be very easy.
Thanks
N
Make Sure the Pressure is released on both tractor and loader will make it easier to connect any hydraulic coupler.
Question, can you use the "Float" feature on the Snowblower attachment? or the front blade?
Defiantly....that would be a good use for Float position to flow the ground contours.
Is it normal for the boom to drift down? When I park it and put the pin in and check it about 4 hrs later the boom is tite against the pin.
When not in use loader valves are not zero leak valves and will leak down over time.
When you got off the seat, the tractor remained running, Mine turns off. Why?
When Tractor Range Lever is in Neutral Position and PTO Lever is Off Position it allows you to leave the seat and the engine remains running.
Thanks, I didn't know that...very useful information.
Is it the same basic procedure for the larger tractors? Say the 4600 or 5600 series
Very Similar on all series of Massey Ferguson Loaders but the 900 Series Deluxe Loaders have lock-n-go that is a little different connection to mid mount frame. The 900X Series Loaders like on 4600/4700 Tractors are very similar to this. Plans are to do more videos showing on each series of tractor as time permits.
Ok, Thanks. Looking forward to it.
We are having a hard time hooking hydraulic lines up when installing the loader can not get the black line to seat . Do you have any tips on that?
Sounds like you have Hydraulic Pressure built up in the line need to loosed the fitting to release pressure. Be careful as Hydraulic oil will leak/squirt out. Wrap a towel around before loosening. If Pressure is on tractor side shut off tractor move joystick in all 4 directions to release pressure and that will help connect hoses too.
SAME ISSUE! RESOLUTION works for me is to wrap the end with a rag, then take a hammer and tap down on the nipple (bulbous ball bearing tip) and it will break the pressure and pop out a bit of hydraulic oil. maybe half an ounce. Thats it. Now the tip will now pop into the receiving coupler when you pull down on the collar. No this is not a porn description! the pressure is so tight in the lines that the ball bearing tip wont recede until you do this. You will need to do it on all 4 of the lines.
can a MF 210 get a grapple bucket. attachment
We didn't get into Massey Ferguson until 2008 the 210 was before our time with Massey Ferguson. Does it have a loader? There are many aftermarket or third party vendors that sell Grapples for all types of tractor loaders.
it does have a loader
has a 216 bucket
Have you check out the W. R. Long Website they make 3rd Function Kits and lots of loader accessories. Or there are numerous other manufacturers out there that make grapples for Compact Tractors like Worksaver, etc.
Why is my mower so hard to hook u p the takes a lot of &@$))(:/ to hook up to shaft
Which Mower MidMount or 3 Point Mower? Are you shifting into Neutral to make it easier to align the shafts? Need more Information to assist
mi dealer find me a ripper tooth at this link
amiattachments.com/attachments.php?link=loader_backhoe-backhoe-rippers
do you know where too find a quick attach for the backhoe
I've never seen for Agricultural Backhoes a Quick Attach System. That might be something available in the Construction Indisty. I would recommend contacting the company of attachment they may sell quick attach systems for Backhoe accessories.
sorry should have mention mi dealer is a Massey Ferguson dealer and mi tractor is a GC1710 and he told me it's the same as a small mini JCB excavator and the link i gave you in mi other comment that company make those attachment but you need too pout there bucket not the one that came whit the tractor.
it would be nice from massey to have a quick attach and a choice of attachment.if you find some thing could you let me know?
and by the way love your video
I will share to Massey Ferguson about your request. There is no industry standard for backhoe attachments yet but it may be coming. ALO Quicke is the Loader and Backhoe Manufacturer and I will mention to them also as they are growing implement selections for loaders but might want to look into backhoe accessories too.
thanks
fill the bucket
That can be done too.
the😥