👋 Hi yall hope all is well, here’s a FFW option for those that just need it. Intro Gears & Locker 0:00 Axle teardown: 0:34 How to pinion setup bearing: 3:47 New Revolution Gears: 5:37 Pinion Depth Setup Theory: 6:30 Pinion preload Setup Theory: 10:34 Carrier setup: 14:35 Powertrax Locker Install: 17:38 Ring gear install: 25:23 Backlash & Preload Theory: 27:03 Carrier Install: 28:50 How to check Backlash 30:18 How to run a gear pattern: 31:30 How to interpret gear patterns: 32:19 Final Build: 34:40 Inner Axle seals install: 34:45 Break in procedure: 41:39
EXCELLENT. Showed the details I was un certain about that every other D30 vid dont show. Great video quality, edits, lighting, no BS... BRAVO! Installing 4.88s with a TruTrak LSD.. Did the rear D44 already and its pretty sweet.
Dude your killing it,I really enjoy your work, I’ve watched so many gear set up videos but you really take the time to thoroughly explain what your process is. Unfortunately I won’t be tackling my gears it’s headed to the shop in two weeks to go from 3:73 to 4:56.
Realy good video, most useful as I am going to be doing my first regear as soon as I get back from our summer holiday. But I wondered why you didn't use the case spreader for the final install of the carrier?
Good luck it’s a bit of a chore you’ll do just fine! And I didn’t use the spreader in that moment just to show that it can be done without it. I did use the spreader most of the time. 🍻🍻
@@ATEMOFFROAD Thanks. I'm fitting an ARB in mine, so process a bit different. But with the copper airline being vilnerable I am trying to avoid using a deadblow to pound the carrier in.
Very cool. Will be a nice selectable locking setup! Definitely recommend using the spreader for both in and out of the carrier. You will still need a dead blow to seat the bearings as the spreader should only open the case no more than 20 thou and it’s not enough to overcome preload. But I do believe your shim stacks will now be on the outside of the bearings?
So I am confused why the side the ring gear is physically on the carrier is called the non-ring gear side and the side the bolt heads are on is called the ring gear side... Seems backward. Also, my GC has the 249J transfer case. Would this PowerTrax locker be acceptable to run in my front diff.?
@@ThatGuyFromArizona the way you mentioned is backwards, left side or bolt hole side for ring gear is Marked R ring gear side. NR is marked for Non ring side. Where do I mention this? Its mainly helpful so you don’t mix up the bearing caps if you plan to make setup bearings with the old. And helpful when making shim stacks for backlash and carrier preload. As far as carrier fitment use the Powertrax website for year make and model. 🍻🍻
👋 Hi yall hope all is well, here’s a FFW option for those that just need it.
Intro Gears & Locker 0:00
Axle teardown: 0:34
How to pinion setup bearing: 3:47
New Revolution Gears: 5:37
Pinion Depth Setup Theory: 6:30
Pinion preload Setup Theory: 10:34
Carrier setup: 14:35
Powertrax Locker Install: 17:38
Ring gear install: 25:23
Backlash & Preload Theory: 27:03
Carrier Install: 28:50
How to check Backlash 30:18
How to run a gear pattern: 31:30
How to interpret gear patterns: 32:19
Final Build: 34:40
Inner Axle seals install: 34:45
Break in procedure: 41:39
I know how much work you put into this!! video turned out great!! good job
Thanks for watching 🙏🍻
EXCELLENT. Showed the details I was un certain about that every other D30 vid dont show. Great video quality, edits, lighting, no BS... BRAVO! Installing 4.88s with a TruTrak LSD.. Did the rear D44 already and its pretty sweet.
Nice, I have the a Detroit tru trac in the rear absolutely love it. 🍻🍻
Dude your killing it,I really enjoy your work, I’ve watched so many gear set up videos but you really take the time to thoroughly explain what your process is. Unfortunately I won’t be tackling my gears it’s headed to the shop in two weeks to go from 3:73 to 4:56.
its my form of meditation. Thanks for watching I appreciate it. 🍻
Great work, and explanation man! I'm really enjoying ur build🤙
Thank you I appreciate it. 🙏🍻
Great video! And great tip on checking clearances on the locker. Didn’t think to do that.
Thanks for watching 🙏🍻
Nice table.
Love the table, been holding up pretty solid.🍻🍻
Great video!
Thank you 🍻🙏
Good video 👍
Thank you for watching I appreciate it. 🙏🍻
Realy good video, most useful as I am going to be doing my first regear as soon as I get back from our summer holiday. But I wondered why you didn't use the case spreader for the final install of the carrier?
Good luck it’s a bit of a chore you’ll do just fine! And I didn’t use the spreader in that moment just to show that it can be done without it. I did use the spreader most of the time. 🍻🍻
@@ATEMOFFROAD Thanks. I'm fitting an ARB in mine, so process a bit different. But with the copper airline being vilnerable I am trying to avoid using a deadblow to pound the carrier in.
Very cool. Will be a nice selectable locking setup! Definitely recommend using the spreader for both in and out of the carrier. You will still need a dead blow to seat the bearings as the spreader should only open the case no more than 20 thou and it’s not enough to overcome preload. But I do believe your shim stacks will now be on the outside of the bearings?
Great videos. What are you doing for outer axle seals?
Do the instructions come with it, ?
Are all the Dana 30s reverse gears ?
( getting parts together to do mine)
@@bob4003 the locker yes , the gears no. If it’s low pinion Dana 30 they are normal cut, High pinion Dana 30 are reverse cut
@@ATEMOFFROAD how does an amateur tell the difference? 🥴
@@bob4003 this video explains everything 🍻ua-cam.com/video/tFJ0jYcF3iw/v-deo.htmlsi=P09c0Tl0_0paGs0K
At 3:35 in video and can't see link to pinion oil baffle mentioned in video, or am I missing the link?
I'm going mad, I can see it now!
Thanks for watching. 🍻🍻
So I am confused why the side the ring gear is physically on the carrier is called the non-ring gear side and the side the bolt heads are on is called the ring gear side... Seems backward. Also, my GC has the 249J transfer case. Would this PowerTrax locker be acceptable to run in my front diff.?
@@ThatGuyFromArizona the way you mentioned is backwards, left side or bolt hole side for ring gear is Marked R ring gear side. NR is marked for Non ring side. Where do I mention this? Its mainly helpful so you don’t mix up the bearing caps if you plan to make setup bearings with the old. And helpful when making shim stacks for backlash and carrier preload. As far as carrier fitment use the Powertrax website for year make and model. 🍻🍻
@@ThatGuyFromArizona www.powertrax.com/traction-systems-product/3151-differential-locker-9204302700/?crt_viaSearch=year%3A1973
Anybody no the part number on the locker the link in description dont work anymore
@@jeremyhanna3852 I’ll check the link thank you 🙏 here’s the locker amzn.to/4fmqnuc
19:30 Good boy! Using metric! 😂
Haha 🤣 yeah didn’t need to take much off there. 🍻🍻
Hey! love your videos
Thank you for watching I appreciate it. 🍻🙏
@@ATEMOFFROAD Can you check your email pls? we sent something to you😉🥰