First time i heard someone explaining using butane for pot i thought he was tripping!!!! Then saw it done and was blown away! Pretty cool process and once you have dabs flower just isnt the same! Thanks for sharing!
I think the butane is horrible to ingest I don’t think you can ever get it all out. I used to stick my pot after I blew it in my sink with hot water and I thought it was pretty clean but probably wasn’t DO ROSIN DABS NO BUTANE THERE
I'm a scientist you should invest in a closed loop system ! Vac oven with a gas recovery system or AKA if you can't afford that go online and buy vacuum purge pump stainless steel Purge pot . You can pull numerous vacuums .. open up the system to allow gas to vent Purge Purge Purge and you don't even have to hit it with the VAC pressure will pull all gases out of your concentrate without affecting any of your terpenes as well as your THC molecules ..
i would not extract the product with chemicals, but if you want to do that i would recommend a Soxhlet-Extraktor with 99 % ethanol to extract the oil. Cool it down in the freezer and fiter the liquid to get rid of wax. then use the filtrate and mix it with cooled Propane. The THC go into the propane layer and the chlorophyl stay in the Ethanol. Separate the two layers, evaporate half the Propane and put the liquid into closed yars at room temperature for several weeks to get nice THCA cristalls to dab. If you have money you can invest into a short path thin layer destillation setup and a vacum pump, but this cost like 1700 Doller +. otherwise you can wash the chrystals.
I had a simmaler set up novice butt it works good also foe filtration u can use a bukner funnle ? I think thats what its called that way u can just use 90% alch insted of butane
I am only 19 seconds in and I already see a potential explosion. If you have the courage to make BHO never do it around any electrical equipment or anything that can generate a spark. Butane is a very heavy gas and it tends to linger and it can ignite at 35F. The safest way to do this is in a open area away from any electrical wires, outlets or anything else that can produce a spark even static electricity can cause butane to explode
I run bho quite regular I believe the floaties are lipids and waxes from the plant and probably some sugars. And the advice on the unbleached coffee filters and silicone collection container is spot on. And yes too much butane will make your stuff thin also not to mention the evaporation time
Word of advice, don't put your Pyrex dish directly on the the hot plate. It can explode into a million glass shards. Instead, have a pot of boiling water on the hot plate and then stack the Pyrex dish on the pot as if you were trying to melt chocolate.
Had a tube years ago, we would freeze the packed tube before we started and quit putting butane in when it started looking less yellow coming out the end
Usually a couple of hours until the tube was a little frosty, seemed like the runs that we didn't freeze it long enough it just took more butane to chill it down at the beginning
In between cans, I like to shake up the extractor to make sure everything was soaked and touched by the solvent. Sometimes you can end up with a dry mid section especially if it's kinda packed in there.
Here’s a pro tip. Dont smoke while you’re off gassing butane lol. That’s how that building blew up in Detroit. All those canisters were butane bottles blowing up.
Those frozen floaties in the extract is most likely water from your bud. If you make a smaller opening or several small openings more pressure will build up inside your extraction tube and literally force the THC infused solvent straight out of the holes. This will make your extraction more efficient.
@@Skunkhunt_42 it's possible but unlikely, especially if one decarbs first. I've been extracting for about a decade now and I've noticed this happens when the bud isn't dry enough, holding too much moisture. I always set my bud out to dry in the air (especially if they have moisture packs) before I extract and noticed that nice, almost "cracker dry" bud, will never have these floaties in it. This is how I've come to this conclusion. It's also frozen which strongly indicates water ice. Something to also keep in mind is that dry bud can also absorb moisture from the air so, if you do an extraction on a day with high humidity, good chance that your bud will absorb some unwanted moisture. And you'll see these floaties but they aren't anything to worry about, they evaporate away.
When I was working in Upper Michigan we all decided to use CO2 and its clean easy and you do not have to chamber it to get it out... Butane will never completly be removed. We studied people who used the butane dabs and they all developed lung problems..
I hate to break it to you but a vast majority of everything dabs most ppl smoke these days is but extraction... unless you buy full ment or rosin(yes I know they use 100 different methods but at least 75% is butane and I'm in a legal state)
@@blazin_bouch710 Yeah bro I pioneered this in upper michigan. I was also the first held hostage for ransom at my grow house. I suggested the use of CO2 and it was then worked into a way of application around 2013 to 15 By an engineer who made a machine out of milling and so on to produce a Patent for it as it was the first of its kind. I am 61 and I was doing this since 1975. Glad to meet you.
@@blazin_bouch710 I doubt you could (Break ) anything to me as I have many years in this before you. To act like you are a source of enlightenment is funny as you are a kid still. Butane is a GHETTO way and Professionals do not use it or recommend it because of health issues.. period...
@@greenmedicinetm299 amen i appreciate ya brotha...anyone thats been a part of getting us to where we are now is an absolute legend .im old enough to remember the mex brick bud more seeds then flower....sativa/indica wasnt even talked about yet...there was one guy in town with worth it stuff...and he knew damn well acted like he was a god....lol to be able to just walk into a store when i dont have any personal stuff and grab something that pretty much has to be atleast decent is pretty crazy looking back
Hey brother just a tip I like to blast straight into really really hot water on l double broiler set up it cuts down out the evap process and takes less time in the vac purge anyways happy blasting
These modern vacuum packers have an optional vacuum hose. I wonder if that might not give better taste to draw off the gas rather than force it off with heat. Like freeze drying, kinda😉
I let iso evaporate naturally, then use the attachment of a vacuum packer with a Mason jar. I vacuum until it stops expanding into satiny and more glossy product.
And here i was freaking out dude watned to stick two pounds of bud in a homedepot bucket with ice water but low and behold he made the best hash ive ever smoked
I just grow,clean,sift, and press my own bud.i have a small press and I can do enough for a week at a time without the butane. I clicked on for a small scale video on shatter because i lovesome good clean shatter. I think i found the right video, ill definitely go outside around nothing electrical. And im probably going to make a stand to hold the tube.
My dad was an electrician. I’m not sure if you guys know this, but every outlet no matter if it’s plugged in or not, electricity bouncing in it. That would mean that plug next to the butane. Gas would explode that dish in a second like a firework that dude is crazy to be blasting butane so close to that plug.
When ever you watch the news and they report that someone blew the windows out of an apartment, or a garage blows up.... This is most likely the reason.
Yes i have done this exactly this way many times 😊😊😊😊and for those who are trying at home just be careful please and fully understand what you are doing
I think if he would have used less butane it would have burned off faster. I have been told that one can is good enough and no more than 2 cans per push
2 cans will only do a Oz really and depends on how many trichromes are on the weed. You need to run gas through till it runs clear. The stuff floating on top of the butane is the fats from the cannabis
Gotta make it run clear or your leaving trichomes in the waste.😢 I personally like all mine out of the waste so however many that takes that's just enough.
@@grimreaper-fg9xz I put my Pyrex plate on top of a pot of water and let it sit there and the warm water would evap it. And it worked just fine. You can still use the hot plate to evap the left over butane
That stuff floating around is Water it comes from blowing through your tube. Your air coming out your lungs has moister in it which inturn freezes before it evaporates. That's why it disappears when your butane evaporates cause your temperature rises in the dish.
But for anybody who plans on trying this remember you must do this with good ventilation and be sure there is no spark Source anywhere or you can have an explosion
He's outside. Much harder to reach LEL at his height with this amount of butane. Could probly even drown his cig out in the butane liquid puddle. The key is nor allowing a vapor cloud to form an area with butane concentration between the lower explosive limit and the upper explosive limit that finds ignition source. Bigger the cloud the bigger the boom.
The stuff floating looks to just be your concentrate! It didn't appear to go away. A huge mat of it got poured into the dish and paper at the end. So idk I'm not a scientist lol lol
Try packing it tighter and when the color of thr liquid coming out isn't green stop ading butane oh and most important dont heat over 98 degrees the terps are distroyed at 114 degrees let it evapetate slow the darker the product the better
@@bammbamm6869 and if you use a fan that says your broke and cant afford a proper fume hood.....probably shouldnt be blasting with possible sparkes from a fan blowing close to something just as flammable as ether
You could have used one less can of butane too once that dark color stopped coming out of the product you were good. Save you a lot of time later on with the boiling off the crap.
Ok so now press the same amount of weed and see the different in yield and then after put the pressed weed in that thing run some butane through it see if theirs difference and then see how much you lose from the press left over.
It's not deadly/toxic when done properly. You need PURE butane. A LOT of high % THC oil in dispensaries is BHO, and it's safe. Cans can be sketchy bc you don't know what the contaminates may be. I like pressed better but the good stuff is pressed from sift or keef. Whereas butane and sometimes CO2 runs can get a similar % THC using flower. BHO made from sift is basically pure THC when done right.
This method is tried and true for results but I've found a different way In a nut shell fill Mason jar with flowers or trim and put flat on jar with holes poked in it so you can submerge the flower in butane . Take off flat and put 2 coffee filters over jar opening and screw on ring Let sit 5 mins Pour the liquid into a cake pan and cook it off Message me if any questions
Any videos or better description ,, probably wouldnt advise this to someone whose never done it or seen it done in person ? Plus i can just go to my dispensary and get w.e the fuck i want for cheap lol ... but i love shit like this and the chemistry and process is awesome to me
thats only going to remove whats crashed out of solution....just go about the process as usual but defat/wax the solution afterwards with alcohol, crystal clear oil afterwards and can be forced into certain crayst states, like sap, pull and snap and shatter
Couldn't it be crystallization of some of the desirable chemicals? Chemical devolved in solvent -> solvent evaporates causing precipitation of potentially thc
@@jamesgrix2201 no it wont crash out of solution like that...the fats,waxes,and lipids do first especially with a liquid solution. even when winterizing the THC still doesnt drop out until conditions are met
Your rooster's got some bass in his crow! How do you determine what "pure," butane is? It's all pretty much the same stuff, isn't it? So, the bulk of the liquid in the glass catch pan, is actually liquid butane, right? I think the stuff floating on top is just the tricons coalescing and sticking together, and forming a 'skin.'
Too my knowledge I believe that it is ice water.water forms from either inside with the butane or from the actual tools that hold the leaf material for blasting i.e from being inside the frazer
thats why pre warming the collection dish in a double boiler system with hot water underneath the pan, blast right into that and it boils off as you blast
dry cracks are only starting at the darker uncured areas...if you gave it 5 times the cure time, dry might be stronger...it's well known that the dryer the wet pour, the stronger it is.
I was focusing so hard at what you were doing the rooster 🐓 in the background jump scared me and I thought your butane can was about to explode or something.. 😆 🤣 😂
Where u get that glass for the butane, I made Dad's better two hot plates and some weights on top.. u can use those mesh bags or even just parchment paper
pvc tube with two caps what we used back in 6th grade 1 can per 8tth we also used hot water to dip the pan in more times the pan was dipped the more butane evaporated could nearly make it clear no yellow but reduced the weight which was worth the loss tho tastes horrible when yellow stay safe everyone
Definitely want to be careful as the Pyrex will burst sometime or another,use a double boiler type heat larger Pyrex with boiling water and concentrate dish floating in it!!!also try whipping it with a whipping tool(dab tool etc) .
Why wouldn't you scrape the glass dish after you heat it all that s*** up and boiling all the butane out? When you put it onto your bowl you left the most of it in the dish. I don't know just seems like a waste to me. Plus how much weed was in that tube? And how much wax did you make.
@@anthonymaize5764 pressure doesnt have much to do with it....super saturation and controlled release of gas is what causes it to crystallize, but yes jars work but break most of the time in my experience, idk if i just cant find the sweet spot or what but a metal pressure chamber i can every time in a few weeks
My first attempt i did an oz but it was homegrown stuff. Its difficult getting a quality result without purging it through a vacuum pump. I winterized mine after a day n a half of boiling it off on a waterbath. After a night of constantly replacing the hot water i threw her in the freezer for a bit and that was my finally product. Burnt and tasted like butane badly so i Know i fucked up by not vacuuming it off. O well better luck next time
My cousin used to put his in freezer but he wouldn't use a whole can all the time some times he'd do a light blast n it would put it n freezer n it made like crumble consistency but I personally like rosin or bubble hash
I done this back in 02, instead of butane used rubbing alcohol. Didn't even know the name for it then, all I knew was I can strip out all the THC from the buds. Everyone thought I was nuts back then and look now it's all over. I didn't even know what to do with it back then, I end up putting it in my cigarettes. (DO NOT DO THAT!!!) I was a teenager
get a big ass pot boil some water and get a pyrex dish that fits over top of the pot and submerges into the water, it may take a bit longer but you always yield amazing crumble if you have initial good product
@@hugostiglitz4452I'd say it's faster, that what I've done too... It just seemed to me to be intuitively, another stage of safely adding boiled water temps & enough heat afterwards... To have to be evaporating & purging out more butane impurities for the process in general. No one mentions it tho?
@@TimesOfTheSines.official my process was hot water bath under the pan until the bubbles stopped being forced out with just hot water temps. then collect into a container and in front of a 1000w heater, constant stirring and nucleating for a half hour or more, left none to trace amounts of butane in the dry crumble. never gcms tested but ive tasted dabs that werent properly purged and one time is enough to get that fucked up taste and recognize it
First time i heard someone explaining using butane for pot i thought he was tripping!!!! Then saw it done and was blown away! Pretty cool process and once you have dabs flower just isnt the same! Thanks for sharing!
It’s better
@@BboyEklypse can't even smoke flower alone after smoking dabs.
@@ChrisandYeisliebecause you’re probably a fiend. Take a break now and again you’d be amazed lol
I think the butane is horrible to ingest I don’t think you can ever get it all out. I used to stick my pot after I blew it in my sink with hot water and I thought it was pretty clean but probably wasn’t DO ROSIN DABS NO BUTANE THERE
@@freshsimpofbelair6050 weed fiend? Nah bro that's not even a thing, weed just sucks after you smoke dabs..
Legend also said he is no longer around after lighting up that ole Marlboro red.
It wasn't a Marlboro, it was a Camel menthol 😂😂😂😂🤢🤢🤢🤮🤮🤮
Your both incorrect it was his home grow product
Haha, wheres the second half haha
😂😂😂😂😂😂😂😂😂😂
@@XeroCool420😂😂😂😂😂😂
I'm a scientist you should invest in a closed loop system ! Vac oven with a gas recovery system or AKA if you can't afford that go online and buy vacuum purge pump stainless steel Purge pot . You can pull numerous vacuums .. open up the system to allow gas to vent Purge Purge Purge and you don't even have to hit it with the VAC pressure will pull all gases out of your concentrate without affecting any of your terpenes as well as your THC molecules ..
i would not extract the product with chemicals, but if you want to do that i would recommend a Soxhlet-Extraktor with 99 % ethanol to extract the oil. Cool it down in the freezer and fiter the liquid to get rid of wax. then use the filtrate and mix it with cooled Propane. The THC go into the propane layer and the chlorophyl stay in the Ethanol. Separate the two layers, evaporate half the Propane and put the liquid into closed yars at room temperature for several weeks to get nice THCA cristalls to dab. If you have money you can invest into a short path thin layer destillation setup and a vacum pump, but this cost like 1700 Doller +. otherwise you can wash the chrystals.
Ok Einstein see a psychiatrist people use what they have you sound narcissistic
@@andrevonthyssen4086what works for you may not work for others Einstein
I had a simmaler set up novice butt it works good also foe filtration u can use a bukner funnle ? I think thats what its called that way u can just use 90% alch insted of butane
And I'm a fucking jet
I am only 19 seconds in and I already see a potential explosion. If you have the courage to make BHO never do it around any electrical equipment or anything that can generate a spark. Butane is a very heavy gas and it tends to linger and it can ignite at 35F. The safest way to do this is in a open area away from any electrical wires, outlets or anything else that can produce a spark even static electricity can cause butane to explode
I know i saw that right off the bat too.
It has a very wide explosion window as far as it’s concentration in air too.
Right when he's like "I got my hot plate at about 100 degrees". I was like "not right now tho right?"
Well outside the gas will rasie to fast in side yes tape your outlets wot duck tap if summer tinfoil windows God was with him this DAY😂😂❤
😂😂😂😂
I run bho quite regular I believe the floaties are lipids and waxes from the plant and probably some sugars. And the advice on the unbleached coffee filters and silicone collection container is spot on. And yes too much butane will make your stuff thin also not to mention the evaporation time
yep exactly what they are insolubles, sucks butane is a bitch to try and dewax with at AP vs iso, or id say just filter it off
Clown comment
When he says 100 degrees on the hot plate. I assume that's Celsius right? Which is 212 Fahrenheit?
Word of advice, don't put your Pyrex dish directly on the the hot plate. It can explode into a million glass shards. Instead, have a pot of boiling water on the hot plate and then stack the Pyrex dish on the pot as if you were trying to melt chocolate.
If you want an easier reclaim method you can use a silicone baking dish as your basin.
i always used a silicone or hard plastic restaurant scraper
@@hugostiglitz4452 you don't need a scraper if the dish you run your butain wash in is made of silicone.
Good tip. Do you take it down to shatter or will it come out when it's still sticky like tar?
@@ElohimYellow i agree but over time the shock of temperature will degrade the silicone over time...glass wont.
Use a silicone bowl stick it in the freezer for 10 minutes when it's done the whole bit comes right out
The contacts on thermostat can spark amd cause an explosion at the hotplate
I personally like using non bleached coffee filter instead of the screen mesh. It helps block any plant matter that may seep thru
I use both
@@basscomander6348 you loser buy a heating press machine and do not smoke gas looool are you living on street that you press weed with butan
That's how i do it@basscomander6348
Had a tube years ago, we would freeze the packed tube before we started and quit putting butane in when it started looking less yellow coming out the end
how long would you freeze the packed tube?
Usually a couple of hours until the tube was a little frosty, seemed like the runs that we didn't freeze it long enough it just took more butane to chill it down at the beginning
@ozCurt hope it helps man, good luck
@@heywatchthis1992 what if you're using really good trimmings instead of nugs and don't have an actual tube?
@@BigCurtDawgdo you still want to know
Legend says its still bubbling to this day ...
You watch to much tik tok
? That didn't originate in tiktok your from Gen Z I'm assuming sorry for your loss
@@joshrangel1296 he meant your attention span has become tok'd
@DasGoodSoup sorry never heard of that term either I'm assuming another tiktok trend ?
I’ve heard a 4 year process is the best way to smoke or dab.
In between cans, I like to shake up the extractor to make sure everything was soaked and touched by the solvent. Sometimes you can end up with a dry mid section especially if it's kinda packed in there.
Here’s a pro tip. Dont smoke while you’re off gassing butane lol. That’s how that building blew up in Detroit. All those canisters were butane bottles blowing up.
Man, I just got a full dose of nostalgia!
Those frozen floaties in the extract is most likely water from your bud. If you make a smaller opening or several small openings more pressure will build up inside your extraction tube and literally force the THC infused solvent straight out of the holes. This will make your extraction more efficient.
I came to the comments wondering what those floaties were! Thanks!
What if it were thca-monohydrate? The mol ratio of thca:h2o inside the trichome is apx 1:1.....
@@Skunkhunt_42 it's possible but unlikely, especially if one decarbs first. I've been extracting for about a decade now and I've noticed this happens when the bud isn't dry enough, holding too much moisture. I always set my bud out to dry in the air (especially if they have moisture packs) before I extract and noticed that nice, almost "cracker dry" bud, will never have these floaties in it. This is how I've come to this conclusion. It's also frozen which strongly indicates water ice.
Something to also keep in mind is that dry bud can also absorb moisture from the air so, if you do an extraction on a day with high humidity, good chance that your bud will absorb some unwanted moisture. And you'll see these floaties but they aren't anything to worry about, they evaporate away.
@@tarlnobert8033 you're welcome! ✌😄
good info.. But when you say make several small openings are you meaning like pockets in the tube? So not to pack the tube densely
When I was working in Upper Michigan we all decided to use CO2 and its clean easy and you do not have to chamber it to get it out... Butane will never completly be removed. We studied people who used the butane dabs and they all developed lung problems..
I hate to break it to you but a vast majority of everything dabs most ppl smoke these days is but extraction... unless you buy full ment or rosin(yes I know they use 100 different methods but at least 75% is butane and I'm in a legal state)
@@blazin_bouch710 Yeah bro I pioneered this in upper michigan. I was also the first held hostage for ransom at my grow house. I suggested the use of CO2 and it was then worked into a way of application around 2013 to 15 By an engineer who made a machine out of milling and so on to produce a Patent for it as it was the first of its kind. I am 61 and I was doing this since 1975. Glad to meet you.
@@blazin_bouch710 I doubt you could
(Break ) anything to me as I have many years in this before you. To act like you are a source of enlightenment is funny as you are a kid still. Butane is a GHETTO way and Professionals do not use it or recommend it because of health issues.. period...
@@greenmedicinetm299 amen i appreciate ya brotha...anyone thats been a part of getting us to where we are now is an absolute legend
.im old enough to remember the mex brick bud more seeds then flower....sativa/indica wasnt even talked about yet...there was one guy in town with worth it stuff...and he knew damn well acted like he was a god....lol to be able to just walk into a store when i dont have any personal stuff and grab something that pretty much has to be atleast decent is pretty crazy looking back
Hey brother just a tip I like to blast straight into really really hot water on l double broiler set up it cuts down out the evap process and takes less time in the vac purge anyways happy blasting
Well bubba, don't know if it was the process or the bowl I smocked, but you got me too watch a pot boil down lol cool stuff
These modern vacuum packers have an optional vacuum hose. I wonder if that might not give better taste to draw off the gas rather than force it off with heat. Like freeze drying, kinda😉
A single stage vacuum pump works very nicely
I let iso evaporate naturally, then use the attachment of a vacuum packer with a Mason jar. I vacuum until it stops expanding into satiny and more glossy product.
Ethanol is my favorite way of extraction that or rosin press. Made BHO for years and perfected it
And here i was freaking out dude watned to stick two pounds of bud in a homedepot bucket with ice water but low and behold he made the best hash ive ever smoked
I just grow,clean,sift, and press my own bud.i have a small press and I can do enough for a week at a time without the butane. I clicked on for a small scale video on shatter because i lovesome good clean shatter. I think i found the right video, ill definitely go outside around nothing electrical. And im probably going to make a stand to hold the tube.
If you're gonna play with butane, avoid any spark risks.
Frrr u can here the lighter in the background😂 making me nervous
Ah butane. I can feel the headache with every hit now
My dad was an electrician. I’m not sure if you guys know this, but every outlet no matter if it’s plugged in or not, electricity bouncing in it. That would mean that plug next to the butane. Gas would explode that dish in a second like a firework that dude is crazy to be blasting butane so close to that plug.
you know nothing about electricity lmao
Ur retarded
And yet it didn’t 🤫
When ever you watch the news and they report that someone blew the windows out of an apartment, or a garage blows up.... This is most likely the reason.
Nah im from TN lol. It's most likely a shake and bake lab here
I'd rather just smoke 😂
Fr 😂
I feel you for real, who wants to smoke gas? Especially butane as a lighter.
THC-A ,Delta 8 ,HHC ,thc-p ? What do you smoke…do you even know what delta 9 is
@lu9077 bro you just named all the corner store strain information 😂
If you purge it instead of just holding it doesn’t freeze the bud as much and you don’t have to use 4 cans
Yes i have done this exactly this way many times 😊😊😊😊and for those who are trying at home just be careful please and fully understand what you are doing
I think if he would have used less butane it would have burned off faster. I have been told that one can is good enough and no more than 2 cans per push
2 cans will only do a Oz really and depends on how many trichromes are on the weed.
You need to run gas through till it runs clear.
The stuff floating on top of the butane is the fats from the cannabis
I’ve been told means u don’t kno shit
1 can per ounce usually is good enough depending on how tight its packed how easily it flows tube size all come into play
Wow drink it.
Gotta make it run clear or your leaving trichomes in the waste.😢
I personally like all mine out of the waste so however many that takes that's just enough.
I never used a hot plate I just used water to evaporate it and it works just fine.
How do you use water tk evaporate water
@@grimreaper-fg9xz I put my Pyrex plate on top of a pot of water and let it sit there and the warm water would evap it. And it worked just fine. You can still use the hot plate to evap the left over butane
That stuff floating around is Water it comes from blowing through your tube. Your air coming out your lungs has moister in it which inturn freezes before it evaporates. That's why it disappears when your butane evaporates cause your temperature rises in the dish.
Try not blowing through it and that stuff will be non existent.
My first vacuum pump was a mason jar fitted with a break bleeder pump 😂😂 looking back now I'm very lucky I didn't blow anything up 😅
Where did u get the tube u put the bud into
Can be built from black or aluminum pipe with a couple appropriate fittings on the ends
But for anybody who plans on trying this remember you must do this with good ventilation and be sure there is no spark Source anywhere or you can have an explosion
Amazon has them
Adult toy shops
Glass turkey baster
It's the dabs forming on top. It evaporates from the top, not the bottom, thus separating there. Then, coming together when the butane is gone.
Try useing r600a it is a butane alcohol mix and use a stainless tube and valve assembly
Get some Hot Hand hand warmers. Put them under the glass tray. The butane evaporates faster.
😂🎉
Reminds me of Freebasing and making up your hits...
Am i the only one that noticed this dude only uploaded one video after this one 3 years ago. Feds ran up on his ass lololololol
Lmao are you smoking right next to the highly flammable vapors?
He's outside. Much harder to reach LEL at his height with this amount of butane. Could probly even drown his cig out in the butane liquid puddle. The key is nor allowing a vapor cloud to form an area with butane concentration between the lower explosive limit and the upper explosive limit that finds ignition source. Bigger the cloud the bigger the boom.
wondering if those magnetic stirers used by chemists would help constantly stirring it while being reduced on the hotplate
Electric hotplate
I myself used to stir mine a lot and I believe it helps 😁
The stuff floating looks to just be your concentrate! It didn't appear to go away. A huge mat of it got poured into the dish and paper at the end. So idk I'm not a scientist lol lol
Try packing it tighter and when the color of thr liquid coming out isn't green stop ading butane oh and most important dont heat over 98 degrees the terps are distroyed at 114 degrees let it evapetate slow the darker the product the better
are you refering to the end product or how saturated the liquid is???
I thought you put a fan on it and it evaporates super fast. My buddy from Cali did it like that at there shop in Humboldt.
Yes you are correct, that's how we do it in Cali...plus you want to push that butane away from you. It lessen the chance of something bad happening 🔥
Yes you are correct, that's how we do it in Cali...plus you want to push that butane away from you. It lessen the chance of something bad happening 🔥
@@bammbamm6869 you sound like a hood chemist.....keep it away from spark and flame outside over a hot water bath.......wheres your risk there
@@bammbamm6869 and if you use a fan that says your broke and cant afford a proper fume hood.....probably shouldnt be blasting with possible sparkes from a fan blowing close to something just as flammable as ether
@@hugostiglitz4452 bro, I was talkin about the old days
You could have used one less can of butane too once that dark color stopped coming out of the product you were good. Save you a lot of time later on with the boiling off the crap.
Ok so now press the same amount of weed and see the different in yield and then after put the pressed weed in that thing run some butane through it see if theirs difference and then see how much you lose from the press left over.
THE STUFF FLOATING AROUND IS ICE
protein.
Plant fats yea?@tribalismblindsthembutnoty124
Yep, from moisture in the product and from the moisture in his breath when he blew in it.
Man have we come along way since this
Just use a press bro that stuff is fkn deadly
Yes sir live rosin babayy
It's not deadly/toxic when done properly. You need PURE butane. A LOT of high % THC oil in dispensaries is BHO, and it's safe.
Cans can be sketchy bc you don't know what the contaminates may be. I like pressed better but the good stuff is pressed from sift or keef. Whereas butane and sometimes CO2 runs can get a similar % THC using flower. BHO made from sift is basically pure THC when done right.
@@FlyingPusssyfoot when done right…
@@weedismyreligion to be fair I wouldn't use this video as a tutorial lol
@@FlyingPusssyfoot 🤣👍
Running the butane through one foot away from electric cord is wild
Dude is gonna go to the moon. Literally.
WE USED TO DO THIS IN THE 90s ya we set out dish in a warm dish of water also
This method is tried and true for results but I've found a different way
In a nut shell fill Mason jar with flowers or trim and put flat on jar with holes poked in it so you can submerge the flower in butane . Take off flat and put 2 coffee filters over jar opening and screw on ring
Let sit 5 mins
Pour the liquid into a cake pan and cook it off
Message me if any questions
You are a hero.
Any videos or better description ,, probably wouldnt advise this to someone whose never done it or seen it done in person ? Plus i can just go to my dispensary and get w.e the fuck i want for cheap lol ... but i love shit like this and the chemistry and process is awesome to me
No use everclear alc in the jar shake it for 2days then boil it out or just let it evaporate naturally
You can do a 10min shake for the honey 🍯
The floaters I believe are the bad waxes probably get a better product if you scoop those out
thats only going to remove whats crashed out of solution....just go about the process as usual but defat/wax the solution afterwards with alcohol, crystal clear oil afterwards and can be forced into certain crayst states, like sap, pull and snap and shatter
@@hugostiglitz4452 defat the solution? Please expound
Couldn't it be crystallization of some of the desirable chemicals? Chemical devolved in solvent -> solvent evaporates causing precipitation of potentially thc
@@jamesgrix2201 no it wont crash out of solution like that...the fats,waxes,and lipids do first especially with a liquid solution. even when winterizing the THC still doesnt drop out until conditions are met
I used to do this 10
Plus years ago. 😊
Chemistry is dope!
If you get a bigger container and put boiling water in it then place the butane extraction container in the boiling water it evaporates a lot safer
Your rooster's got some bass in his crow!
How do you determine what "pure," butane is? It's all pretty much the same stuff, isn't it?
So, the bulk of the liquid in the glass catch pan, is actually liquid butane, right?
I think the stuff floating on top is just the tricons coalescing and sticking together, and forming a 'skin.'
Too my knowledge I believe that it is ice water.water forms from either inside with the butane or from the actual tools that hold the leaf material for blasting i.e from being inside the frazer
thats why pre warming the collection dish in a double boiler system with hot water underneath the pan, blast right into that and it boils off as you blast
no. Its protein.
It's moisture from butane contaminated by water from blowing out the cylinder
Yeah 3drops of water 💦 in the purge
dry cracks are only starting at the darker uncured areas...if you gave it 5 times the cure time, dry might be stronger...it's well known that the dryer the wet pour, the stronger it is.
This brings back good memories I remember doing this in 6th grade
I was focusing so hard at what you were doing the rooster 🐓 in the background jump scared me and I thought your butane can was about to explode or something.. 😆 🤣 😂
Lol!😂
Wow! 😳 One word… BOOM ! 💥
This is pretty much the same reason,
why I got interested in learning about chemistry😂
Where u get that glass for the butane, I made Dad's better two hot plates and some weights on top.. u can use those mesh bags or even just parchment paper
pvc tube with two caps what we used back in 6th grade 1 can per 8tth we also used hot water to dip the pan in more times the pan was dipped the more butane evaporated could nearly make it clear no yellow but reduced the weight which was worth the loss tho tastes horrible when yellow stay safe everyone
Definitely want to be careful as the Pyrex will burst sometime or another,use a double boiler type heat larger Pyrex with boiling water and concentrate dish floating in it!!!also try whipping it with a whipping tool(dab tool etc) .
Put a fan above your ventilation to prevent your body from taking in oxygen
Would a press be more safe?
you remind me of the guys I would play call of duty with when I was a little kid
legend has it he is still filming seeing colors he cant explain
can someone explain how this Badass just picked up a glass dish boiling with no glove. I Have to say im really impressed 😶💯
Only way to find out what the floaters are is to remove some and dry it
Thx, I’ll stick with the cold press
This is so old now but the floating stuff has to be the plant waxes solidifying because of the heat
We did it in Humboldt with 8ft long schedule 40 6inch pipe.
you can use a air compreser to blow the rest threw also do you smoke the left over bud
There’s is no way you can smoke that bud afterwards… is there?
No the bud is useless now. (Plant matter*)
Hell no don't smoke the leftover
@@Town_Country96hell naw shit will give you cancer or some shit
@@Town_Country96😂 no it was a joke its flameablw
I would try to scoop it out and see the difference
Amazing Very Cool.
How to get a knock from the FBI
The safe and proper way to purge the butane is with a pan of hot water instead of a live heat sourse
Is UA-cam shoeing how to make dabs or am I high?
Why wouldn't you scrape the glass dish after you heat it all that s*** up and boiling all the butane out? When you put it onto your bowl you left the most of it in the dish. I don't know just seems like a waste to me. Plus how much weed was in that tube? And how much wax did you make.
And in your opinion do you think a second run doing this is necessary??
why not just huff the butane?
Stupid😂😂😂..he found a better way to drink it lmfao
Just out of curiosity how much flower went into that tube and is it ground or whole flower?
I think he mentioned 60 gr in the beginning.
An Oz
That 🐓 feeling the DAB EFFECTS IN THE AIR POP THE BUBBLES TO BUDDY
Legend has it the chickens are still out
Did you grind up your bud before hand?
I was told to make sure leaves or product to be dried beforehand
Clearly smoking while evaporating butane….brilliant
All the money you end up having in butane in a year you could have a really nice press. Probably not even a year depending on how often you do this
I think it’s the fats n waxes but I’m not sure I get the same stuff when I evap my butane too
If you put some in jar with a lid on it and open it once in awaile you will make thc diamonds (90%+ purity and the rest is terpenes).
Yeah it dont work like that
@bylly nallee actually it does you create thc crystals with presure fact check me.
@@byllynallee9238 ua-cam.com/video/Z7XZ7hcg8bk/v-deo.html
@bylly nallee you don't take all the butain out of the material when you put it in a Mason jar so it will gain presure.
@@anthonymaize5764 pressure doesnt have much to do with it....super saturation and controlled release of gas is what causes it to crystallize, but yes jars work but break most of the time in my experience, idk if i just cant find the sweet spot or what but a metal pressure chamber i can every time in a few weeks
My first attempt i did an oz but it was homegrown stuff. Its difficult getting a quality result without purging it through a vacuum pump. I winterized mine after a day n a half of boiling it off on a waterbath. After a night of constantly replacing the hot water i threw her in the freezer for a bit and that was my finally product. Burnt and tasted like butane badly so i Know i fucked up by not vacuuming it off. O well better luck next time
My cousin used to put his in freezer but he wouldn't use a whole can all the time some times he'd do a light blast n it would put it n freezer n it made like crumble consistency but I personally like rosin or bubble hash
RUN IT UP DOPEE STUFFF !!!!!!!!!! YOU EVER GO INTO PRODUCTION YOU LET A BROTHER KNOW , ID LOVE TO TRY . STAY SAFE
I done this back in 02, instead of butane used rubbing alcohol. Didn't even know the name for it then, all I knew was I can strip out all the THC from the buds. Everyone thought I was nuts back then and look now it's all over. I didn't even know what to do with it back then, I end up putting it in my cigarettes. (DO NOT DO THAT!!!) I was a teenager
Where do you get the filters for tube from
What else can you do if you can't vaccum purge?
get a big ass pot boil some water and get a pyrex dish that fits over top of the pot and submerges into the water, it may take a bit longer but you always yield amazing crumble if you have initial good product
@@hugostiglitz4452I'd say it's faster, that what I've done too... It just seemed to me to be intuitively, another stage of safely adding boiled water temps & enough heat afterwards... To have to be evaporating & purging out more butane impurities for the process in general. No one mentions it tho?
@@TimesOfTheSines.official my process was hot water bath under the pan until the bubbles stopped being forced out with just hot water temps. then collect into a container and in front of a 1000w heater, constant stirring and nucleating for a half hour or more, left none to trace amounts of butane in the dry crumble. never gcms tested but ive tasted dabs that werent properly purged and one time is enough to get that fucked up taste and recognize it