Can you please make a full video from start to finish for CZ 457 MTR stock, Not sure where you will need to drill holes. I'm thinking using an 8" or 10" rail. Thanks
I had some problems with this. First, the Manners PRS TCS stock's line down the "center" was not in fact centered so I was a good bit off once the rail was threaded on and had to redo, my mistake I should have visually confirmed with the rail. Second and more disappointingly, is that tapping in the T-nuts bulged the bottom of my stock so the rail would not sit flush. I tapped it back in and am clamping it flat and filling the hole with epoxy. I drilled a third hole, clamped the rail in place and tapped in the T-nut with something on the other side protecting it from budging. I now have three holes instead of one to install the rail.
Do you find that the prongs on the T nut bite well enough that not epoxy on the T nut is necessary? Not that under bolt clamp load it would move, but more, if I had to remove and install the arca plate? The more I type it out the less is seems needed
Getting ready to purchase a 14" ARCA lock rail for my CZ 457 Varmint MTR and one for my CZ 457 Varmint. I watched your other video on installing about an 1/8" forward of mag release on the MTR. How many t-nuts should I install for the best hold with minimal injury to the wood? Should I use the rear most hole?
I’d like to know the length of that ARCA rail? I’ve got a custom barrelled action coming with a Manners T4A and I’d really like to instal a system like this but I’m no fan of the rail extending beyond the forend
Thank you so much for this video! It's an old video but still very valuable.
Thanks, you guys are awesome
Can you please make a full video from start to finish for CZ 457 MTR stock, Not sure where you will need to drill holes. I'm thinking using an 8" or 10" rail. Thanks
I really like the Camo patterns Manners use on these stocks. I wonder if I could get similar results using sponges and Krylon fusion.
Bergara and savage have aluminum bedding chassis built in. How do you install on these?
Curious would this rail fit a McMillan a3-5 stock , not sure if it accepts the front action screw or not
I had some problems with this. First, the Manners PRS TCS stock's line down the "center" was not in fact centered so I was a good bit off once the rail was threaded on and had to redo, my mistake I should have visually confirmed with the rail.
Second and more disappointingly, is that tapping in the T-nuts bulged the bottom of my stock so the rail would not sit flush.
I tapped it back in and am clamping it flat and filling the hole with epoxy. I drilled a third hole, clamped the rail in place and tapped in the T-nut with something on the other side protecting it from budging.
I now have three holes instead of one to install the rail.
Thank you for posting this
Do you find that the prongs on the T nut bite well enough that not epoxy on the T nut is necessary? Not that under bolt clamp load it would move, but more, if I had to remove and install the arca plate? The more I type it out the less is seems needed
Getting ready to purchase a 14" ARCA lock rail for my CZ 457 Varmint MTR and one for my CZ 457 Varmint. I watched your other video on installing about an 1/8" forward of mag release on the MTR. How many t-nuts should I install for the best hold with minimal injury to the wood? Should I use the rear most hole?
For your stock I would follow closely the instructions given in that other video. The two stocks are quite similar from a mounting perspective.
I’d like to know the length of that ARCA rail? I’ve got a custom barrelled action coming with a Manners T4A and I’d really like to instal a system like this but I’m no fan of the rail extending beyond the forend
This is a 14" ARCA rail you want a 12" if you dont want it to extend beyond the front.
Derek Rosenberg thanks for the reply mate