@@SeanLewisMedia Ive noticed using flux resin instead of a core solder you get a better application, especially microsoldering. Just seems like a much easier flow. Food for thought.
I definitely appreciate the tip and will make sure I pin this comment so people can see it. You are 100% right too. I havent soldered any small boards in a while but I do remember the last time I did it was much easier and promoted way better flow using your method. Have a good one!
When it comes to soldering heat and speed is your friend. Using inadequate heat will heat soak the wires and circuit board. Tin both parts, align them and apply heat to the wire. The heat will transfer through the wire and into the base metal. With a little practice your solder joints will look perfect.
To avoid the solder spreading on two connectors I recommend using a separator like aluminum foil or any thin metal piece and place it between the two connectors before soldering. Other than that, excellent job! P.S expect the soldering police to swarm. 😂
Dude I had no idea they existed. So far everyone has been nice so I appreciate that. I really like that idea of a separator between them and I’m glad you told me that idea. Thanks for the help!
Im so glad it helped man! I know it can be stressful but im glad your trying it. If you ever have extra wire or pieces sitting around you can always practice with those. ive done that a bunch in the past just to practice. I did get tips to use more flux on mine so its always a good idea to have some around. Have a good one!
This is such a great video! Soldering looks complicated and this video really helped me understand how it actually works!! I love how if you make a mistake you can correct it with the solder sucker 👍 great job!👏 the rc car is looking awesome 😎
Aww Im so glad! Its not hard, its just a bit scary to start and get into because the consequences seem huge. A bit of practice with scraps would be a great way to get better too! The solder suckers is a life saver haha! Thank you! and thanks for watching!
Dude, theres a lot of soldering videos out there but this was really helpful! I appreciate the time you took into doing this. Now, my biggest thing/fear is that I'm going to either damage the electrical component by heating it too long or I melt the plastic off connectors because of the same. I try to make a really clean looking connection so I end up spending a lot more time keeping everything hot and melted than I probably should at times. Also, I think I need a new tip on my soldering iron because I did not know in the beginning how to protect the soldring tip. I like to use shrink wrap on everything. I know it probably doesn't hurt anything but how you have it exposed just gives me anxiety! lol. It's my OCD I'm sure. Oh, and that's another thing, my wire will sometimes end up getting to hot and start shrinking the wrap before It's supposed to! Anywho, as much in life, practice makes perfect right? Thanks again for sharing!
Man you hit so many common issues right on the head for sure! I used to do shrink wrap on everything too but I’ve gotten away from it just to save time haha. I’m used to the race buggy side of things too and weigh savings mattered in stock buggy so we shortened everything haha even servo and esc wires. It’s honestly pretty crazy how much heat the electronics can take. I know this one got really warm at one point. Thanks for watching as always man!
great informative video! you should get a lot more speed and traction with that rear esc 🔥🔥 btw did you make that carbon esc mount for the hydra top deck? ive been looking for something like that cuz my esc barely sticks on lol
Much appreciated! Soldering is definetely one of those things that takes some time to get comfortable with but worth it! So my buddy actually made a few for our group of friends. Im going to hang out with him today so Ill see if he has any left for you🤘🏼 If not ill see if he wants to make a run of them so people can get them. I can help him get them to people:)
Thanks mate this vid helped me. Anyone know the best quality wire to use? My hobby store gave me some generic Chinese stuff. I want something premium. EBay is full of the cheap stuff. Also which gauge to use? 12-14 okay for my xerun v10 g3 6.5t to my xerun xr10pro. Thanks x
Not going lie, I have no idea haha. I purchased the motor from a friend and it came included on there. It has worked great and I just left it. I’m not sure who makes that one but it’s there. I appreciate you watching!
Your solder joints are i bit dry. The easiest way to tell is when the solder cools it should have a very shiny finish, it shouldnt be dull. You just need to use some flux, im sure it will be fine for now though just something to try next time. Apart from that good tutorial !!
@@SeanLewisMedia i just googled and i see what u mean. I read it can also be used to stabilize voltage, also it will allow the passage of AC but not DC. Im thinking in the case of RC maybe its being used to prevent the esc from frying if you were to cross the leads into the battery. I also read the description of the accuvance XX and that is what theyre using it for
@@FullBeardSk8 Awesome to know the details thanks! I do think your correct about the reverse protection on the hobbywing! I feel like ive read that before. I know accuvances are more performance claim based and they have a bunch of options.
Flux !
Yes its essential! I always use flux core solder to ensure things bind. Its not a bad Idea to have some on the side incase you get in a jam though!
@@SeanLewisMedia Ive noticed using flux resin instead of a core solder you get a better application, especially microsoldering. Just seems like a much easier flow.
Food for thought.
I definitely appreciate the tip and will make sure I pin this comment so people can see it. You are 100% right too. I havent soldered any small boards in a while but I do remember the last time I did it was much easier and promoted way better flow using your method. Have a good one!
@@SeanLewisMedia All good man, either way, just like to share my travels. Wonderful video you have created!
When it comes to soldering heat and speed is your friend. Using inadequate heat will heat soak the wires and circuit board. Tin both parts, align them and apply heat to the wire. The heat will transfer through the wire and into the base metal. With a little practice your solder joints will look perfect.
@@Scramblerkidd I appreciate it!
Little tip from an FPV drone pilot: solder from left to right, it's easier that way. Nice Video!😉
Thank you! I appreciate all the advice I can get🤘🏼
I was watching this as I was soldering, thank you brotha!
That’s awesome man! Glad it was useful and I appreciate you watching!
To avoid the solder spreading on two connectors I recommend using a separator like aluminum foil or any thin metal piece and place it between the two connectors before soldering. Other than that, excellent job! P.S expect the soldering police to swarm. 😂
Dude I had no idea they existed. So far everyone has been nice so I appreciate that. I really like that idea of a separator between them and I’m glad you told me that idea. Thanks for the help!
I just butchered a soldering job (first time trying it) so this video comes at a perfect time, thanks for showing the screw up and how to fix it too
Im so glad it helped man! I know it can be stressful but im glad your trying it. If you ever have extra wire or pieces sitting around you can always practice with those. ive done that a bunch in the past just to practice. I did get tips to use more flux on mine so its always a good idea to have some around. Have a good one!
This is such a great video! Soldering looks complicated and this video really helped me understand how it actually works!! I love how if you make a mistake you can correct it with the solder sucker 👍 great job!👏 the rc car is looking awesome 😎
Aww Im so glad! Its not hard, its just a bit scary to start and get into because the consequences seem huge. A bit of practice with scraps would be a great way to get better too!
The solder suckers is a life saver haha! Thank you!
and thanks for watching!
Dude, theres a lot of soldering videos out there but this was really helpful! I appreciate the time you took into doing this. Now, my biggest thing/fear is that I'm going to either damage the electrical component by heating it too long or I melt the plastic off connectors because of the same. I try to make a really clean looking connection so I end up spending a lot more time keeping everything hot and melted than I probably should at times. Also, I think I need a new tip on my soldering iron because I did not know in the beginning how to protect the soldring tip. I like to use shrink wrap on everything. I know it probably doesn't hurt anything but how you have it exposed just gives me anxiety! lol. It's my OCD I'm sure. Oh, and that's another thing, my wire will sometimes end up getting to hot and start shrinking the wrap before It's supposed to! Anywho, as much in life, practice makes perfect right? Thanks again for sharing!
Man you hit so many common issues right on the head for sure! I used to do shrink wrap on everything too but I’ve gotten away from it just to save time haha. I’m used to the race buggy side of things too and weigh savings mattered in stock buggy so we shortened everything haha even servo and esc wires. It’s honestly pretty crazy how much heat the electronics can take. I know this one got really warm at one point. Thanks for watching as always man!
great informative video! you should get a lot more speed and traction with that rear esc 🔥🔥 btw did you make that carbon esc mount for the hydra top deck? ive been looking for something like that cuz my esc barely sticks on lol
Much appreciated! Soldering is definetely one of those things that takes some time to get comfortable with but worth it!
So my buddy actually made a few for our group of friends. Im going to hang out with him today so Ill see if he has any left for you🤘🏼 If not ill see if he wants to make a run of them so people can get them. I can help him get them to people:)
What size bullet plugs are you using and after that do you just stick the plugs into the abc holes of the xd10 motor?
They came included with the esc, but I believe they are 4mm. They plug right in to the motor like you said. It makes switching motors out easy.
@@SeanLewisMedia I really appreciate the help!
Thanks mate this vid helped me. Anyone know the best quality wire to use? My hobby store gave me some generic Chinese stuff. I want something premium. EBay is full of the cheap stuff. Also which gauge to use? 12-14 okay for my xerun v10 g3 6.5t to my xerun xr10pro. Thanks x
@@pesh909 I usually use 12ga Deans Ultra Wire or 12ga Deans Wet Noodle. It’s a little harder to find but really high quality wire👌🏼
nice vid wonderin why u have the acuvance capacitor ?
Not going lie, I have no idea haha. I purchased the motor from a friend and it came included on there. It has worked great and I just left it. I’m not sure who makes that one but it’s there.
I appreciate you watching!
Your solder joints are i bit dry. The easiest way to tell is when the solder cools it should have a very shiny finish, it shouldnt be dull. You just need to use some flux, im sure it will be fine for now though just something to try next time. Apart from that good tutorial !!
Thank you! I’m definitely not a master and can always use suggestions!
always has solder iron on the tip, so it can transfer the heat better
Yes exactly
N1 video
I soldered purple cables to my ESC
that looks cool too
I took a picture for you but UA-cam deletes my commend all time if i ad the link
Purple wires would be sick! Try sending it on Instagram if you want🔥
@@SeanLewisMedia oh yeah, I didn't even think about Instagram ^^😅
@@RiaRayku Haha no worries!
@@SeanLewisMedia did you get the pictures?
u dont know what the cap is for 🤨
Its stores power but there’s a lot nonsense being sold in the market too.
@@SeanLewisMedia i just googled and i see what u mean. I read it can also be used to stabilize voltage, also it will allow the passage of AC but not DC. Im thinking in the case of RC maybe its being used to prevent the esc from frying if you were to cross the leads into the battery. I also read the description of the accuvance XX and that is what theyre using it for
@@FullBeardSk8 Awesome to know the details thanks! I do think your correct about the reverse protection on the hobbywing! I feel like ive read that before. I know accuvances are more performance claim based and they have a bunch of options.
@@SeanLewisMedia yeah so its probably worth having id say, a little protection for peace of mind
@@FullBeardSk8 For sure! at least the one that comes included! If its there its there for a reason haha