That was one of those high dollar ratchets that change from a breaker bar to ratchet depending on the shot.....starts as a ratchet at 11:57.....12:04 is a breaker bar with ratchet sounds lol
Great video guys I love me a square body! I can’t count how many I’ve owned through years but I love the direction the truck is going, will be watching for next episode 👍🏻
Great video but I would say if going to suggest deep creep make sure it "creeps" lol. Right before this a nut was removed that was sprayed but the threads had no oil under the nut. Just say remove the nut the spray oil and put it back on to make it look like its working haha.
on every bolt they sprayed Deep Creep on, none of the threads showed that it actually creeped under the nut or up the threads. it only made the exposed threads wet
It was easier to add EFI and have that aftermarket system control the 4L80, price of external controller and needed TPS is not cheap compared to a single PCM controlling everything, fans, fuel etc.
It should've been clarified that there's a 4L60 and a 4L60E transmission, and that the controller only works on the E version. The 4L60 is basically an improved 700R4 with hydro shifting controls, while the E is all done electronically. There are only E versions of the other GM transmissions mentioned.
TCI shafted me on th350 trans. When I told them my problem the guy said it was my stall convertor showing shavings in the pan. So I took it apart and found the sprags broke and few other parts bad. Manual valve had chip in it fluid bleed off in the pan. When contacted TCI again and sent the pictures. They said 30 day warranty on race transmission. They would not do anything about it or offer to repair it. The guy was not so nice over the phone. Trans was bought 8/2020 install 10/2020, 2nd gear went out 3/2021. Only 160 miles light street driving. I hope you don't go through what happen to me.
My opinion the best factory color combo ever. I'm assuming not going for mid engine as stunt truck had however all wheel drive will rip! Go square shit box or go home! 😂
I would have pop-riveted those cab corner patch panels on. People turn their nose up at pop rivets, imagining that welding is the "correct" way to do it, yet, ironically, it's superior to butt-welding in cases like this, because now you have a bare weld on the inside that you can't paint due to lack of access, and a bare weld rusts like it's its job. I wish I had a dollar for every few-years-old butt-welded patch job I've seen that had rust coming through precisely along the weld. On the other hand, I know for a fact that pop-riveted patches can last for decades without rust problems, at least not any that are caused by the method of attaching the patch.
im guessing because they think youd be using a lot more bondo to cover a rivet vs a smooth weld . a buddy of mine had this tool that would bend the metal in that area to lay the patch panel over lapping the seams . he used a body glue to bond them together . after bondo and paint you couldnt tell by looking at the truck . he did it to show me you dont have to be a welder / fabricator to do some rust repair your self ........ at least on cab corners .
@@867diesel "im guessing because they think youd be using a lot more bondo to cover a rivet vs a smooth weld" They make countersunk pop rivets, as well as drill bits for use with them that drill the hole and then countersink it so you don't have to use two different bits. Countersunk pop rivets don't require any more Bondo to cover them than a ground down weld does.
@@MaximRecoil yeah true . its definitely another way of doing it and not needing the welding machine and all the bs that goes with it . on my next squarebody ill try the rivets
Don't understand why gearbox was pulled to fix flex plate, New brakes and flexies, locking hubs, engine tune, wash and polish it then drive through a moss hole. Then remove it all and replace again for higher spec stuff. Why not straight to big block spec
Well. I think he's still doing it as we haven't seen a finished product. Which I guarantee will be a better build given the reputation these guys have.
@@jamesbarnett4166 outside of Pat and Frankie the rest is pretty much unwatchable at this point. Pat is a knowledgeable engine builder. I basically watch the rest to laugh at what they are hacking up. I mean they bubba pretty much everything at this point.
Can you guys do yet another 4x4? I mean really, I don't think you guys have done enough of them................. Rolling my eyes...... How about doing a damn street truck? Not everyone is into 4x4's, In fact not alot of people are, how about building a an affordable, daily driver classic street truck, I'll even go so far to say I wouldn't even care if it was a Ford, but if you do a Ford do a 7th Gen (80-86) bullnose F-Series truck, just to show everyone that even the ugliest truck can be a cool street truck, because even as Bowtie Guy I've seen enough Squarebodies and OBS trucks. Be different, do a bullnose or a 3rd gen Dodge D-series truck and make it a 2wd street truck.
If I was you l will go with long bed step side it worth a lot of money and some things different and they sold in Saudi 1979 with 100 KM for $200000 Thousand dollars all original and its long bed step side with all original paper and the original sticks and the seat original factory paper covers
Now let's see if they actually paint it or are they just going to be lazy like usual? After seeing the rust repair and that massive paint run I think it would be better for them if they don't let Shaggy do the painting.
You mean the paint drip inside of the corner that will never been seen? These guys are far from lazy and do great work. Does not take much energy to be a keyboard warrior like yourself though.
Disappointed. When I click to get price info from your drop-down info, all I get is a Prompt to join Rebrandly. Guess you guys are not making enough $$$ from Ads and the like. 👉✈🏴☠ Hijacked!!!
Way to ruin a square body by going drivers side front diff 👎they were pass side diff. Also to much stall on the converter not needed at all just going to add unwanted heat to transmission and waste low end torque. Lastly big power big axels and half ton frame how's that going to end not well. The fall guy truck was a 3/4 ton with a small block and 36's and did fine for what it was. You have taken a good square body and ruined it again as usual.
Enter for a chance to win a free set of Continental tires: swee.ps/KZZxRgfNP
That was one of those high dollar ratchets that change from a breaker bar to ratchet depending on the shot.....starts as a ratchet at 11:57.....12:04 is a breaker bar with ratchet sounds lol
Great video guys I love me a square body! I can’t count how many I’ve owned through years but I love the direction the truck is going, will be watching for next episode 👍🏻
Wish I had a nice big clean garage, and lots of money 😆.
You could if you had your own show and sponsors
Yeah I don’t think there’s anyone that doesn’t..
Those threads, where the nut was, were dry as f after he removed that nut by hand lol.
3K stall seems awful high for a 4x4 big block truck. I went with a converter from a 6.5 Detroit/T400 setup that has a stall closer to 1500 RPM
I was thinking the same. Around 1800 would be perfect
Great video but I would say if going to suggest deep creep make sure it "creeps" lol. Right before this a nut was removed that was sprayed but the threads had no oil under the nut. Just say remove the nut the spray oil and put it back on to make it look like its working haha.
Just like how the far away shot is with a ratchet, but close up is with a breaker bar.
I think that stall on that converter is a bit high for a pickup! 2400-2800 would of been better.
1500 would have been fine, the bbc torque should have no problem getting things rolling that low!
on every bolt they sprayed Deep Creep on, none of the threads showed that it actually creeped under the nut or up the threads. it only made the exposed threads wet
Oh brother!
ya serve no use did not get in tread at a ll lol just a waste honestly
Watch project farm you tube channel on penetrant tests. Nothing works very well except for heat.
😂😂😂
That truck was very clean. I don't think it really needed any penetrating fluid. I second the project farm testing results.
You guys Rock
It was easier to add EFI and have that aftermarket system control the 4L80, price of external controller and needed TPS is not cheap compared to a single PCM controlling everything, fans, fuel etc.
Great video can't wait for more content from flog box
Love the square bodies!!!
Been hanging for this build took you boys long enough
"O" nice job on the truck. I'm working 1991 4x4 k1500 and plymouth arrow truck.
It should've been clarified that there's a 4L60 and a 4L60E transmission, and that the controller only works on the E version. The 4L60 is basically an improved 700R4 with hydro shifting controls, while the E is all done electronically. There are only E versions of the other GM transmissions mentioned.
He said it was an E
One of my favorite builds
When money and sponsership is no object.
Yep that's what I want in a 4x4 a high stall converter NOT
TCI shafted me on th350 trans. When I told them my problem the guy said it was my stall convertor showing shavings in the pan. So I took it apart and found the sprags broke and few other parts bad. Manual valve had chip in it fluid bleed off in the pan. When contacted TCI again and sent the pictures. They said 30 day warranty on race transmission. They would not do anything about it or offer to repair it. The guy was not so nice over the phone. Trans was bought 8/2020 install 10/2020, 2nd gear went out 3/2021. Only 160 miles light street driving. I hope you don't go through what happen to me.
once again its better to use a GOOD local shop to rebuild one
اللهم صل وسلم وبارك على عبدك ورسولك محمدﷺ
Brilliant video.
Would you do the paint prep/sanding with the front clip in or off? I’d have no where to put it unless I buy one of those racks you have.
My opinion the best factory color combo ever. I'm assuming not going for mid engine as stunt truck had however all wheel drive will rip!
Go square shit box or go home! 😂
I have the same original paint on my 85 k10 suburban
I would have pop-riveted those cab corner patch panels on. People turn their nose up at pop rivets, imagining that welding is the "correct" way to do it, yet, ironically, it's superior to butt-welding in cases like this, because now you have a bare weld on the inside that you can't paint due to lack of access, and a bare weld rusts like it's its job. I wish I had a dollar for every few-years-old butt-welded patch job I've seen that had rust coming through precisely along the weld. On the other hand, I know for a fact that pop-riveted patches can last for decades without rust problems, at least not any that are caused by the method of attaching the patch.
im guessing because they think youd be using a lot more bondo to cover a rivet vs a smooth weld . a buddy of mine had this tool that would bend the metal in that area to lay the patch panel over lapping the seams . he used a body glue to bond them together . after bondo and paint you couldnt tell by looking at the truck . he did it to show me you dont have to be a welder / fabricator to do some rust repair your self ........ at least on cab corners .
@@867diesel "im guessing because they think youd be using a lot more bondo to cover a rivet vs a smooth weld"
They make countersunk pop rivets, as well as drill bits for use with them that drill the hole and then countersink it so you don't have to use two different bits. Countersunk pop rivets don't require any more Bondo to cover them than a ground down weld does.
@@MaximRecoil yeah true . its definitely another way of doing it and not needing the welding machine and all the bs that goes with it . on my next squarebody ill try the rivets
I would have went with Atlas 2 gear drive transfer case other than that it awsome
Im just wondering why the bed bolts had to removed just take the tailgate off🤔🤣@12:50
Electronic control transmission?
Should have done EFI too.
It’s become 8 minutes of wrenching and 18 minutes of infomercials.
Don't understand why gearbox was pulled to fix flex plate, New brakes and flexies, locking hubs, engine tune, wash and polish it then drive through a moss hole. Then remove it all and replace again for higher spec stuff. Why not straight to big block spec
restoring ford excursion v10. Or not 🤷♂️
Why not put bed liner on the cap Corners they would never rest again
Your front diff is on the wrong side?
probably only going to cost 50k.
Hi guys I have a 1990 chevy k1500. It won't shift out of 3rd gear. Need help pls.
you need a transmission
Hay can you do a Ford f150 or f250
You know Stacy David did a Fall Guy truck ?
Well. I think he's still doing it as we haven't seen a finished product. Which I guarantee will be a better build given the reputation these guys have.
@@bmstylee seems like some of these prokects get half assed
@@jamesbarnett4166 outside of Pat and Frankie the rest is pretty much unwatchable at this point. Pat is a knowledgeable engine builder. I basically watch the rest to laugh at what they are hacking up. I mean they bubba pretty much everything at this point.
was going to say the same thing about Stacy David building one, I thought it was finished.
I don that your pumpkin is on the wrong side of the truck
Just a little late on this Stacey David Gears did it and fix it better. I am fine saying that and I haven’t even seen the finished product
Stacey's truck looks really good. However, with his MO it will be a while before we see it finished.
He finished it Never took us for a ride in it
why does topolinsky look so angry when he's doing they dyno test?
Can you guys do yet another 4x4? I mean really, I don't think you guys have done enough of them................. Rolling my eyes...... How about doing a damn street truck? Not everyone is into 4x4's, In fact not alot of people are, how about building a an affordable, daily driver classic street truck, I'll even go so far to say I wouldn't even care if it was a Ford, but if you do a Ford do a 7th Gen (80-86) bullnose F-Series truck, just to show everyone that even the ugliest truck can be a cool street truck, because even as Bowtie Guy I've seen enough Squarebodies and OBS trucks. Be different, do a bullnose or a 3rd gen Dodge D-series truck and make it a 2wd street truck.
you would think after all these years chevy/GMC would fix the problem with the bottom corners of the cabs rotting out
It's not just GM. Cab corners and wheel wells are rust prone. Sound deadening material eventually gets moisture on it and the rest is elementary.
Fall Guy Truck was a LONG BED..
They never said it was going to be a replica
Are there people working in a shop with m@sks on?
So I see a lot of keyboard warriors on here. What show are you on and when, so we can all benefit from your expertise?
It not a 85 k10 the head light style is wrong the headlights are saying it a 81 K10
Fall guy tribute? How exactly is this a fall guy tribute?
stay tuned and find out lol
@@everettgrover9459 they already said what they are doing.
👍👍👏👏👏
You must have said k10 square body 10 times in the first 30 seconds......
these trucks and always their cab corners :(
Thankfully a rat motor
Stacey David beat yall to it and did it better
The jesus of christ is happy!
@real_teriadrianna wow scams on here now too
Why put that electronic crap in an older truck? That's part of the reason to rebuild them to get away from that crap. Simplicity
If I was you l will go with long bed step side it worth a lot of money and some things different and they sold in Saudi 1979 with 100 KM for $200000 Thousand dollars all original and its long bed step side with all original paper and the original sticks and the seat original factory paper covers
Now let's see if they actually paint it or are they just going to be lazy like usual? After seeing the rust repair and that massive paint run I think it would be better for them if they don't let Shaggy do the painting.
You mean the paint drip inside of the corner that will never been seen? These guys are far from lazy and do great work. Does not take much energy to be a keyboard warrior like yourself though.
Disappointed. When I click to get price info from your drop-down info, all I get is a Prompt to join Rebrandly. Guess you guys are not making enough $$$ from Ads and the like. 👉✈🏴☠ Hijacked!!!
First
And thats the best you could come up with?
@@aeroflopper am i supposed to come up with something?
How about keep it a small block. Big blocks are overrated.
as the saying goes, no replacement for displacement
Way to ruin a square body by going drivers side front diff 👎they were pass side diff. Also to much stall on the converter not needed at all just going to add unwanted heat to transmission and waste low end torque. Lastly big power big axels and half ton frame how's that going to end not well. The fall guy truck was a 3/4 ton with a small block and 36's and did fine for what it was. You have taken a good square body and ruined it again as usual.
I want REVENGE....Put a FORD engine in a GM car/truck.
A '57 Chevy with a Coyote FORD engine.
Lost my interest at carburetor! Id went fuel injection!
Going to put a stupid LS engine in to?
watch the video.... carbed big block
Yes. Let's not use one of the best small blocks ever. I never hear people complain about Hemi swapping a Mopar or Coyote swapping a Ford.
Definitely not an LS it's a Big Block Chevy and a 4L80E
Surprised they didn’t pressure wash it first to get all that crud off of it first 🤷♂️
@speer147gr LS is great but it's been played out on this shows.