Smith & Wesson M&P M2.0 in 10mm is Quickly Becoming a Favorite
Вставка
- Опубліковано 14 гру 2022
- The S&W M&P M2.0 10mm has become one of my favorite guns after shooting for the past six months. Combined with the Holosun 507K on top and its accurate and a ton of fun at the range. Have you shot the M2.0 in 10mm? Let us know what you think in the comments below!
- Навчання та стиль
Used Floyds Custom aluminum base plate to increase the magazine ammo capacity by one at 16. Did it on all my magazines.
The ergonomics of it are just perfect for me, it's my favorite pistol. I'm not using a red dot, & have the largest backstrap installed. The trigger is noticeably gritty, I bought mine used, & wasn't sure if that's why the previous owner traded it in - that's my only gripe with the firearm. I find most of the 10mm ammo at the store isn't much better than 40 S&W, so you gotta pick the right ammo if you want [most] all the power.
I have the 4" and love it! It jammed about 3 times in the first 100 rounds. I installed a 22 lb recoil spring and it hasn't jammed since.
Hey do your mags rattle When fully loaded and in the gun? I noticed when I loaded the mags to full capacity, it rattles like gravel in a Can, I took out one round and it didn’t rattle much. I’m planning on getting some springer precision mag springs made specifically for the MP10.
@@unitedwestanddividedwefall3521 I changed my mag springs...And just so happens, I got one of them to stop rattling, and I can carry 15+1 in one mag. ..and it also mitigated alot of the misfeeds that Clay mentioned...I'm gonna eventually also get a new recoil spring, that's what alot of other M&P 10 guys been saying online.
Where do you get the new spring at ? Do you have a link? Is it direct drop in?
@@TheSodFather09 I put a 22 lb recoil spring in my 4" M&P 2.0 10mm. I bought it from Galloway Precision (part# GP-162-22-BLK). It was a perfect fit/match and I had it changed in less than 60 seconds without any tools. BUT... I am curious about trying the 24lb spring as the 22 still ejects the brass a long way.
Mine does the same rattle/stuck follower thing fully loaded in the gun. It also doesn’t like to feed the last two rounds of any ammo type. I think these have magazine springs that were meant for the 45acp. I don’t like putting aftermarket parts in my guns but I might try a stronger mag spring for starters unless Smith has a revised version they can send me. It only has about 50 rounds of various ammo through it so far. Maybe needs more use to break it in, who knows..
I love my M&P 2.0 4.625 inch 10mm with no safety lever. Used an Apex aluminum flat trigger upgrade using a model for M&P 2.0 9mm, 40 S&W and 45 ACP but the gunsmith needed to adapt it as the M&P 2.0 10mm frame is a little larger. Using a Holosun 508T solar panel backup red dot using a C&H Precision aluminum mounting plate with stainless steel screws and blue-loctite. I tried putting stronger springs and messed up the reliability. Went back to the original spring and it is reliable. Will get mine ported by Mag-Na-Port eventually. Thanks for posting your review.
Thanks for the reply and watching, Jeffrey!
Can you post a link for that C&H plate please? I couldn't find which one I need and I don't want my screws to shear off my optic.
@@Moderndaycowboy74 call C&H Precision and talk with them like I did.They assisted me with quality customer service.
@@jeffreylocke8808 thank you sir, I appreciate the reply
I was afraid to get one when it first came out and was the first to review Glocks new Gen 5 10mm it was flawless but I still love the S&W!
My trigger was gritty too when I first got it. I replaced the striker safety spring and plunger with one from Apex Tactical and it smoothed up the trigger considerably. My pistol is the 10mm 2.0 4” version. I did that replacement to the following 2.0 9mm, 2.0 40s&w, 2.0 10mm 4.6”, and another 2.0 4” 10mm. It took care of the gritty problem on all of them.
It's my favorite EDC 10mm pistol, I use a custom made leather holster as I had the same experience with the texture of the grips. Great overall gun
Rubber talon grips solves your no undershirt issue.
Went with the 4.6 barrel model with holosun 507c. Started off with 507k and just didn't really like it plus the 507c can run on solar which was a plus for me. I had 1 ftf in first magazine but has been running great since. I the the problem is the angle of the feed lips and not spring tension. All my other pistol's magazines point the round right into the chamber while the m&p points way up. They polished the feed ramp very well but the round never touches it.
Got mine right now. It's my EDC....Replaced my Canik TP9 Elite SC... its undoubtedly slimmer than the Canik. I didn't mean to carry a 10mm...But hey..😁
I just got the 4.6” 10mm and I really like it. Can’t wait to reload different rounds for it.
If you're gonna load HOT rounds for it get a Wolff 24 pound recoil spring & guide rod for it. It's the same as the .45 acp spring. It helps a lot
@@garymccausland1272 I also have a 45 s&w full size I can snag the guide rod out of to see if it helps.
Thanks for watching, Jesse! Need to start reloading now.
The 10 mm and the 45 both have 16 pound springs of the same dimensions. Get the Wolff 24 pound spring & guide rod
I have the 4.6 model with holosun red dot & it’s been flawless. I do recommend changing out the mag springs since it’s what been causing issues for some .
Did you have to change the mag springs on yours?
@@TheSonsOfSimon I did change out the mag springs just to avoid any issues.
Hey would anyone know if I can switch the slide lock bar for a smaller one that comes on the m&p 9? Reason I ask is because, my m&p 10 won’t fit my micro roni :(. The slide buttons on the side makes it too wide.
I’d much rather have the 10mm in a Kriss Vector for sure
Just FYI . . if you wind up carrying this gun or another gun with the 507K you can expect to replace the battery in a few months. Typically you'll find that you need to run the reticle on the second highest setting and the shake awake is pretty sensitive. It isn't such a big deal though because you can change the battery without removing the optic.
I carry daily and my battery is still going strong after 18 months.
Do you clean the barrel on these hand guns when u get them ? Or she already clean ?
I was looking into getting the 4 inch, but heard so much about all the issues with it... now im leaning towards the springfield XDm compact
You probably made a smart decision. S&W has had my 4.6" 10mm for about 3 weeks now due to the failure to feed issues that many others are complaining about. They are telling me a 5 week turnaround on it. If it is not flawless when I get it back, I am selling it and moving onto something else for 10mm
@tasburath I love my xdm, over 2000 rounds thru it without a malfunction.... looking into trying out the new sig Xten comp though. For whatever reason sigs carry 10x better than other brands for me.
Have you had any issues with the optic plate staying on?
Heck. In. Based!!!
I’m trying to find a nice Iwb holster for it 4inch barrel.
I got the 4.6 and it's my first handgun and I really like it but idk what I wanna do with it all what sight would be best and I plan on getting a new spring and barrel any opinions?
I imagine you found a solution but I got the Performance center model and I replaced the springs with some from springer precision. The extra power ones. I’d say holoson is your best choice for a red dot. Also got the extra round base pads for the magazine. So 18 rounds total instead of 15.
My M&P10mm is my go-to for bears in alaska... it's proved itself in a pinch already with a mountain lion. 3rds and down.. I'm satisfied. I don't hunt anything but deer. I carry a 10mm for the nastiness in life..
I cary a G40 in Alaska, but I really like this one better. Half the people have jams and half don't. I'm not sure what to do with that.
@@Alaska_MD I'll tell ya... I run hard cast bear loads in my M&P. Never a stovepipe or jam.
Is there a version of this for ca ???
@@ecarrollpa bahahahahaha
Coming from the 1911 platform, I think all polymer triggers are garbage. That being said, I do own afew.
Burnish/polish the trigger transfer bar and the take up grit vanishes. That stamped piece is always rough on m&p where it ramps on the striker lock button.
$ik 👽
👊💪🤙🇺🇸
Shoot it without the red 🔴 dot to show us how accurate the gun shoot 🎯💥💥💥🔫
10mm is the best millimeter
A “wrist breaker”??? Are you sure you’re in the right video category?
S&W support out right told me you can not use underwood ammo in this gun. You can use ammo running at 40 cal numbers fine. But full 10mm loads and this thing is not reliable. Get a RIA 1911 or a Glock if you want to depend on a gun for your life with 10mm. First and last S&W for me.
Don't let that turn you away. S&W lifer and haven't ever had a single issue 1000s and 1000s of rounds.. that 10mm though... the early reports are very disappointing that there was ever any issue.. and its the one I REALLY wanted too. But don't let this one off turn you away. M&Ps are stupendously good.. apparently except for full power high grain 10mm loads in this 1 model
It’s because you used to be soft now your just a little tougher also the Glock 10mm does suck 😅
I bought the same model 6 weeks ago. Liked the 4" for carry (vs my longslide MOS G40). Kinda having a hard time finding anything else to like.
I ran some PMC and Sig 180 as well as Underwood and Buffalo Bore in full power, 200 & 220gr loads. It cycles the PMC & Sig well. But that stuff is loaded to hot 40S&W velocities: not to 10mm velocities. If I'm gonna carry something that shoots a .401 180gr at 1100fps, I'll just run hot 40S&W in a smaller piece.
The fact it won't reliably cycle full power 10mm as it comes from the factory is very disappointing. I mean these guys built the original FBI 10mm autos to run full on 10mm.
I like your optic choice. The 507K is great. I have a couple of a 19 and a P365X. Wouldn't have occurred to me to run one on a full-size device.
And the trigger. Well, I dislike it enough I ordered a Timney trigger for 2.0. Haven't installed it yet.
I'll reserve judgement for now, but it is not going to make a carry piece in factory form. And that's disappointing. Smith makes or 2.0 that are really great items.
I agree on the point of not being reliable from the factory, but in my research and personal experience most of this is remedied externally. I have a 24lb. RSA from Galloway (mine is 4.6") and I installed Springer Precision extra-strong mag springs in my mags. There are a couple of good write-ups on the main reason for failing the heavier loads - mag geometry. The bullets with thicker meplat (200/220gr hardcast) can physically push out the mag catch because the magazine channeling ribs start "too late" as compared to other M&P 2.0 models (40, 45). For me I've decided to just use Underwood Xtreme Penetrators. They are still "full house" 10mm, yet bullets are not too wide. Zero issues. I also have about 300 rounds of just range ammo through mine and it seems to also have "broken in" (I know, it's a contentious term). I need another test with the hardcasts. My other idea was a "hybrid load"- 10 rounds of Xtreme Penetrators in the mag, topped off with the 5 hardcasts, plus one in the chamber. That way the hardcasts never touch the mag catch. I tested and had no issues. And keep it cleaned. I feel like we have a really good gun with poorly designed magazines and weak stock RSA. Easy to replace the RSA but someone at S&W should be demoted for those mags. Oh, the feed lips are also too short, that's the other problem. Still "external" to the gun itself. I'm still learning to trust mine, as well as learning to use a red dot on it.
@@languagesource355 I bought the Springer Precision springs as well as a couple of their +5(?) extensions. I installed one spring in one mag. No change. I bought 22 and 24lb recoil springs from NDZ. No change.
I bought a 10mm barrel and extractor for my Glock 41 MOS (5.3"). No more problems. It's bigger than I wanted, but I was carrying it with very hot 45 Super before, so...
The 2.0 will likely never leave the safe again.
@@Swampytheroot it's not so much the power of the loads, as it is the shape of the heavier bullets, all about physical dimensions and poor mag design. Personally I think that this causes both, FTF and the mag drops, just depending on tolerances of each situation (gun/mag/ammo). I also think they went with this mag design to cram an extra round in the flush mag. Sad. M&P45 is same frame size, same mag chassis and the mag channeling ribs are proper and it all works just fine. Some even modify 45 mags for the 10mm. Still, very sad. If I was in your situation, I'd ship it back to S&W, as many times as it'd take. Let them bear the costs of their decisions.
@@languagesource355 I sent it back twice already. I'm disgusted with them. At this point, it's wasted time. I may sell the NIB Timney trigger, the mag and recoil springs and the SCS optic off just to cover half the loss. See if a pawn shop has something worthwhile they're willing to trade for a basically new S&W 10mm. Oh, also found a place selling extra factory mags for under $35 with free shipping with a $100 purchase, so those can be rehomed, too. I've spent more time on a max range rifle. I have too many other handguns that run as close to perfect from the factory to waste time on this one. I have the G40, G41, a 610 and a GP100 in 10mm. Those all work without wasting hours and hundreds of dollars trying to coax them.
Your putting weak ammo in it put true 10mm in it and it might be a different story
You don’t have to shoot expensive hot stuff all the time. I load 135s way lower than “full power” and it makes range shooting more enjoyable not getting blasted by your own gun
Also all the malfunction issues I’ve seen is the factory recoil spring. It’s got a lighter one in there but I bet they did that knowing a lot of people are buying this instead of 40, so not only are most people running something like “the fbi load” most people would think a 22 or 24 lb recoil spring is too stiff. Especially with a small thin slide like it has I bet a lot of reviews would ding it as hard to rack under pressure.. But it’s a man’s gun at the end of the day, need a chick gun go buy a bersa 380 so I get where the consternation comes from.. get you a new recoil spring and the slide won’t be moving too fast for the magazine anymore
So much recoil for no reason they sell 9mm ammo that will shoot with same or more velocity and kinetic energy than the 10mm cartridge without the extra recoil lol
Keep smoking that good sh!t bro.👍
Can you say "Stopping Power"! 10mm>9mm
Never go full retard. You went full retard. Can’t even make 9mm as powerful as properly loaded max 38 special.
@@thorshammer5134 Chrono speaks differently. I go based on facts not what a bunch of keyboard warriors say lmaoo do some research and stop with the ignorance
You have 9mm that will get over 700 foot pounds from a 4.5 inch barrel?