2008 2009 2010 2011 2012 Honda Accord Fender Removal How to Remove Replace Install

Step by step how to remove the fender on a 2008 2009 2010 2011 2012 Honda Accord.
Bumper Removal -- • 2008- 2012 Honda Accor...
Headlight Removal -- • 2008 2009 2010 2011 20...
Wheel Well Fender Clip -- amzn.to/2E6htSL
Lower Rear Fender Clip -- amzn.to/2DCjrLj
Upper Garnish clip -- amzn.to/2CMVHBA
Clip Tool -- amzn.to/2GjMioz
Painted Replacement Fenders 2008-2012
Left Driver Side Sedan 4Dr -- amzn.to/3BLyxtq
Right Passenger Side Sedan 4Dr -- amzn.to/3IsMGy0
Left Driver Side Coupe 2Dr -- amzn.to/3BSSzlN
Right Passenger Side Coupe 2Dr (Not Painted) -- OUT OF STOCK

[@joshm3469]

The first half of the video you spent explaining plastic push clips, great job.

[@LuisRivera-rw6xz]

I definitely appreciate the video champ. I will be trying to do this today. Praying I can do it lol

[@realestateness]

Thanks for this video! The 13’ LX model was little different that there were only 4 tabs in wheel well and a bolt underneath the edge of the door and also a tab beside it. The tools helped a lot. The tabs in wheel well was a real pain to remove.

[@ashrahbari1426]

I would imagine they're a bit different because 2013 is the next gen 😅 Glad it worked though

[@franciscomelendez3398]

Great video!!!
Quick question do you.know if the outter roof panel can be removed for thos same car?

[@RigoStar1931]

Just what i needed. Thank you sir!!

[@luismoreno9188]

Dam on some no homo shit, I would like to give you a hug cause you just saved me a shit ton of money bruh 🤙🏻

[@damongupta4266]

watching the bumper cover removal and the headlight - do you actually have to remove them both? Seems like if you remove the vertical phillips head screw, and a few of the pins on the underside of the vehicle (under the bumper cover), then you can access that 10mm bolt that secures the headlight to the fender. If you remove that, and then do everything else you show for the fender, will that allow the fender to come off, or do you still have to remove the light, and thereby the bumper cover?

[@zxzhaixiang]

just did that yesterday. yes it is possible to reach the 10mm bolt without taking off the entire bumper and headlight. there are actually two 10mm needs to be removed, one attaching the headlight to the fender, one attaching the fender to the frame. it was pretty awkward to access the two bolts with the bumper on. if I would do it again, I would remove the bumper first. no need to remove the headlight for sure

[@shamilsons]

Hi, first of all thank you for the video, can you provide a link to buy pre-painted front right side fender?

[@jjparra9042]

Extreme auto body parts and paint....google it

[@TheAnnieSisters]

What are the tiny black screw/pins that are also there, I can't figure out how to remove them

[@franciscomelendez3398]

you are the man!!!

[@zacharygonzales2543]

Do I have to take it all apart or can I just find something to pop it out. With

[@AWD_T]

Does that rocker piece on the bottom of the fender come off?

[@DIYHonda]

That part is riveted to the fender so it’s part of the fender assembly. To take it off, you will need to take the whole fender off.

[@condordiving6864]

Good video. Thanks

[@GenericYouTubehandle910]

Does this car have a sunroof? Trying to locate where the drain tubes exit on a similar car.

[@Mohammad-hv3hy]

Should i completely remove the bumper and the headlight or i can just loosen them and work?

[@franchisefred4066]

Thank u sir

[@rawlbro]

Hello, can you name the clips that are on the lower part of the wheel fender liner

[@Cesar62509]

Great video . What’s the name of the tool you used with the hook you used to remove the fender well

[@oldguss]

It is usually referred to as a pick and hook set but you can buy them individually as a hook tool

[@mikelon1010]

Awesome vids.... Show me how to remove the gas door please... 10th gen. Thanks

[@lexicrawford3141]

Does anyone know what the part is called that is between the fender and the door? The plastic ones and you have to push on it to release the fender from the clips?

[@DIYHonda]

www.google.com/search?q=2008+accord+fender+close+out&ie=UTF-8&oe=UTF-8&hl=en-us&client=safari#ip=1&oshop=apv&oshopproduct=cid:16176245667289395066,oid:9752065862956023585,iid:10089024020932206480,pvt:hg&piu=ps:28&pvs=0

[@henrytaylor5047]

Same process for a 2009 TSX 4cyl?

[@dailyinspirations76]

Great! Appreciate thus video!

[@starsick7]

What about those tiny little screws bolts that also adhere the fender? You skipped those

[@TheAnnieSisters]

Did you ever find out? I am stuck on these

[@777Justin]

@@TheAnnieSisters Those are rivets and I ended up sawzawing the fender off. Usually drill those out, but I didn't have the right bit at the time.

[@lorenzoortegamiranda9152]

Gracias 😎

[@Jayztunning]

You dont have to remove the headlight nor bumper , to remove the fender

[@johnneran2916]

He needs that labor

[@j30amj]

Who thought of the Hodge Twins with the song at the end?

[@slaniejode2318]

Don't look like you need to take the headlight off to remove the fender?

[@tompayne1159]

You have to because the bottom light bracket attaches to the fender

[@billymurrell1422]

!